Table of Contents
Advertisement
This Remote Start/Alarm System is designed to be used with Automatic Transmission- Fuel Injection Gas or
Diesel Vehicles Only!
INSTALLATION OF THE MAJOR COMPONENTS:
CONTROL MODULE:
Select a mounting location inside the passenger compartment (up behind the dashboard). The mounting
location selected must be within 24" of the ignition switch wiring harness to allow connection of the 6 pin main
wiring harness. Be certain that the chosen location will not interfere with proper operation of the vehicle. Avoid
mounting the module to or routing the wiring around the steering shaft/column, as the module or wiring may wrap
around or block the steering wheel preventing proper control of the vehicle. The module will be secured after all
wiring is completed which will allow complete access until the job is done.
Do Not Mount The Module In The Engine Compartment, as it is not waterproof.
HOOD PIN SWITCH:
The pin switch included in this package is intended for protecting the hood area of the vehicle. In all cases, the
switch must be mounted to a grounded metal surface. When the pin switch is activated, (hood open), it will
supply a ground to the input wire activating the alarm. In addition, the hood switch is required for the safety shut
down of the remote start unit. If the vehicle is being worked on, this hood switch prevents the remote start
activation even if the RF command to start is issued. This switch must be installed in all applications. Failure
to do so may result in personal injury or property damage.
THE PUSH-BUTTON PROGRAM SWITCH/LED/RECEIVER/ANTENNA:
The Superheterodyne Receiver Antenna Assembly provided with this unit allows routing from below the dash
board for maximum operating range. Choose a location above the belt line (dashboard) of the vehicle for best
reception. Special considerations must be made for windshield glass as some newer vehicles utilize a metallic
shielded window glass that will inhibit or restrict RF reception. In these vehicles, route the antenna toward a rear
window location for best reception. Secure the antenna with double stick tape provided.
DO NOT PLUG THE SIX PIN MAIN POWER HARNESS OR THE MULTI PIN INPUT / OUTPUT HARNESS INTO THE
CONTROL MODULE UNTIL ALL CONNECTIONS TO THE VEHICLE HAVE BEEN MADE. AFTER SELECTING
YOUR TARGET WIRES AS DEFINED BELOW, DISCONNECT THE NEGATIVE BATTERY CABLE FROM THE
VEHICLE BATTERY PRIOR TO MAKING ANY CONNECTIONS.
Note: Do not remove the fuse holders from this wire harness. Fuses must be used and located as close
as possible to the power source for adequate protection of the vehicle.
WIRING THE 6 PIN MAIN POWER HARNESS:
Note: Do not remove the fuse holders from this wire harness. Fuses must be used and located as close
as possible to the power source for adequate protection of the vehicle.
1 VIOLET Wire: Accessory Output
Connect this wire to the Accessory wire from the ignition switch. This wire will show + 12 volts when the ignition
switch is turned to the "ACCESSORY" or "ON" and "RUN" positions, and will show 0 volts when the key is turned
to the "OFF" and "START" or "CRANK" positions.
2 BLUE Wire: Ignition 1 Output
Connect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when the ignition key
is turned to the "ON" or "RUN" and the "START" or CRANK" positions, and will have 0 volts when the key is turned
to the "OFF" and "ACCESSORY" positions.
For Diesel Applications, this wire must be connected to the ignition circuit that powers the glow plugs if the vehicle
requires glow plug pre-heating. (See selectable feature Bank 3 #11)
3 Fused RED WIRE: + 12 Volt Battery 2 Source
Locate the vehicle battery wire(s) at the ignition switch. Verification: These wires will register voltage in all
positions of the ignition switch. Connect the Red wire to the vehicle's battery wire. This wire provides power for
the start relay and the accessory relay.
4 Fused RED/WHITE WIRE: + 12 volt Battery 1 Source
Locate the vehicle battery wire(s) at the ignition switch. Verification: These wires will register voltage in all
positions of the ignition switch. Connect the Red w/White wire to the vehicle's battery wire. This wire provides
power for the control circuit as well as the ignition 1 and ignition 2 relays.
PART # 1365038
PART # 1363699
IMPORTANT!
PART # 1123742
4
PART # 1181202
128-8801b
4 of 20
Hide quick links:
Advertisement
Table of Contents
