Related Manuals for Code Alarm CA 4051
Summary of Contents for Code Alarm CA 4051
-
Page 1: Remote Start
PROFESSIONAL SERIES Remote Start Installation Guide CA 4051 2010 Audiovox Electronics Corporation. All rights reserved. -
Page 2: Table Of Contents
Programming Feature Banks ..............13 Tach Programming .................. 14 Smart Tachless Mode ................14 Feature Descriptions ................15 Transmitter Button Functions ............. 17 Remote Start Shutdown Diagnostics ..........17 System Layout ..................18 2010 Audiovox Electronics Corporation. All rights reserved. -
Page 3: Before You Begin
Use a Digital Multi Meter for testing and verifying circuits. DO NOT USE A TEST LIGHT, OR "COMPUTER SAFE PROBE" as these can set off air bags or damage vehicle computers. Technical Support (800) 421-3209 or go to http://techservices.codesystems.com 2010 Audiovox Electronics Corporation. All rights reserved. -
Page 4: Pin Main Harness
FACTORY DISARM / PULSE BEFORE START ( - ) LT BLUE FACTORY ARM / PULSE AFTER START ( - ) GREEN/WHITE PULSE AFTER SHUTDOWN ( - ) BLACK/YELLOW PULSE DURING CRANK ( - ) 2 Pin Lock Output Harness 2010 Audiovox Electronics Corporation. All rights reserved. -
Page 5: Pin Main Harness
Jump To PINK BLUE/BLACK Active Output Accessory Output Wire Ignition Output Wire Wire From Wire From Control Module Control Module To Vehicle's 2nd or 3rd Accessory Wire To Vehicle's 2nd or 3rd Ignition Wire 2010 Audiovox Electronics Corporation. All rights reserved. - Page 6 Locate the vehicle’s brake light wire at the brake pedal mounted switch. Verification: This wire registers positive voltage when the brake pedal is pressed. Connect the BROWN/RED wire to the vehicle’s brake light wire. 2010 Audiovox Electronics Corporation. All rights reserved.
- Page 7 Connect the WHITE wire to the parking light output wire. Negative switching Parking Lights: Connect the WHITE/RED wire to a good chassis ground. Connect the WHITE wire to the parking light output wire. 2010 Audiovox Electronics Corporation. All rights reserved.
-
Page 8: Pin Start Harness
RUN) position, but not the ACC (Accessory) position. The voltage does not drop out when the key is turned to the START (or CRANK) position. Connect the PINK/WHITE wire to the vehicle’s ignition 2 wire. Programmable output: IGN, ACC, Start. 2010 Audiovox Electronics Corporation. All rights reserved. -
Page 9: Pin Alternate Output Harness
This wire will supply a ( - ) 200mA pulse upon a successful completion of the remote start activation sequence and is typically used to re-lock the vehicle’s doors upon remote start if necessary. 2010 Audiovox Electronics Corporation. All rights reserved. -
Page 10: Pin Door Lock Output Harness
To Vehicle's 2nd S tarter W ire 2 Pin Lock Output Harness BLUE UNLOCK ( - ) The door unlock output wire provides an output only while the remote start feature is active. 2010 Audiovox Electronics Corporation. All rights reserved. -
Page 11: Additional Ports
Diesel Glow Plug Input Door Lock Control Passlock / Passkey Interface (GM Only) Dome Light Supervision Transponder Interface Activation Factory Alarm Arm / Disarm Manual Arm / Disarm Inputs (factory keyless controls system) 2010 Audiovox Electronics Corporation. All rights reserved. -
Page 12: Set Up & Programming
Press the BRAKE to change the desired feature. The LED will flash indicating the changed feature. NOTE: The system will remain in feature programming mode as long as the ignition is on, there is no time limit. To exit programming turn the IGNITION OFF. 2010 Audiovox Electronics Corporation. All rights reserved. -
Page 13: Transmitter Programming
Feature Bank 3 - 5 Flashes 1 LED Flash 2 LED flash 3 LED Flash 4 LED Flash 5 LED Flash 6 LED Flash Output Control Double Pulse 1 Second 1 Extended Lock Pulse 3.5 Seconds Unlock 2010 Audiovox Electronics Corporation. All rights reserved. -
Page 14: Tach Programming
Within the 7 flash time period, press and hold the button. One extended parking light flash (1.5 seconds) will indicate the system is now in tachless mode. 2010 Audiovox Electronics Corporation. All rights reserved. -
Page 15: Feature Descriptions
Hybrid (Crank Average / No Voltage) - Determines crank time by averaging the last 8 times the vehicle was started with the key. DBI Port - Monitors the vehicle’s tach rate through an interface module connected to the DBI port. 2010 Audiovox Electronics Corporation. All rights reserved. - Page 16 Start / Crank - Crank output during remote start. 11 - 2 or 3 Hour Start: When activated, the remote start will activate and run for the programmed time and shut down every 2 or 3 hours. 2010 Audiovox Electronics Corporation. All rights reserved.
-
Page 17: Transmitter Button Functions
3 seconds. FLASHES TRIGGER ZONE 3 Flashes Hood Input Brake Input 4 Flashes Remote Start Valet Mode 7 Flashes Tach not learned / Crank Average not learned 2010 Audiovox Electronics Corporation. All rights reserved. - Page 18 2010 Audiovox Electronics Corporation. All rights reserved.
- Page 19 2010 Audiovox Electronics Corporation. All rights reserved.
- Page 20 2. This device must accept any interference received, including any interference that may cause undesired operation. Warning! Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 2010 Audiovox Electronics Corporation. All rights reserved.
Need help?
Do you have a question about the CA 4051 and is the answer not in the manual?
Questions and answers