Related Manuals for Altinex Multi-Tasker MT103-104
Summary of Contents for Altinex Multi-Tasker MT103-104
- Page 1 MULTI-TASKER MT103-104 is shown above. MANUAL PART NUMBER: 400-0090-004 MT103-104/MT103-109/MT103-110 6-OUT VGA DISTRIBUTION AMPLIFIER EXPANSION CARDS FOR MULTI-TASKER ENCLOSURES USER’S GUIDE...
-
Page 2: Table Of Contents
INSTALLING YOUR MT VGA DA EXPANSION CARD ..............8 OPERATION (FOR MT103-104 ONLY)....8 7.1 RS-232 CONTROL...........8 7.2 RS-232 INTERFACE........8 7.3 DESCRIPTION OF COMMANDS.....8 7.4 SUMMARY OF COMMANDS ......1 2 TROUBLESHOOTING GUIDE......13 ALTINEX POLICY..........14... -
Page 3: Precautions / Safety Warnings
1.1 GENERAL frequency energy and, if not installed and • Qualified ALTINEX service personnel, or their used in accordance with the instruction authorized representatives must perform all manual, may cause harmful interference to service. -
Page 4: About Your Mt Vga Da Expansion Card
15-pin Crosstalk -39dB @ 15MHz HD connectors to 5 BNC connectors using DC Offset +/-20V max, input = 0V ALTINEX adapter cables. Output Sync Signal Horizontal, Vertical TTL (+/-) For high performance applications, the MT103-104 Impedance... -
Page 5: Product Description
MULTI-TASKER PRODUCT DESCRIPTION APPLICATION DIAGRAM Application 1... - Page 6 MULTI-TASKER Application 2: Internal View of the MT VGA DA Expansion Cards...
- Page 7 MULTI-TASKER Application 3: RGBHV Switching Use the MT103-104/(109)(110) card for RGBHV signals to display more than 6 monitors. You need one MT103-104/(109)(110) Expansion card and one MT103-102/(103) MT VGA DA card.
- Page 8 MULTI-TASKER Application 4: Connection of MT103-102/103 to MT103-104/109/110...
-
Page 9: Installing Your Mt Vga Da Expansion Card
MULTI-TASKER computer control system or any other device INSTALLING YOUR MT VGA DA EXPANSION capable of sending RS-232 commands. CARD 7.2 RS-232 INTERFACE Step 1. Connect the 10-pin IDC cable from the MT VGA DA Card (MT103-103/102) to The RS-232 commands for the MT103-104 are control port, in a simple ASCII character format. - Page 10 MULTI-TASKER without Ui (use command ; see user’s If there is no card in slot #2 of unit 3, there will [SETU0] guide for the MT100-100). be no feedback. Example: 3. [CiS] [VERC3]: for unit ID zero This command saves the current status of the [VERC3Ui]: for unit ID other than zero card's input to output configuration.
- Page 11 MULTI-TASKER To enable output 1 of card 6 and output 3 of Example: card 7 simultaneously, use the following Turns ON only outputs 1 and [ON12C5U3]: commands: 2 of the MT103-104 card located in slot #5 [ON1C6U3P] of the MT100-100 Enclosure with unit ID3. [ON3C7U3P] Turns ON only output 3 of the [ON3C5U3]:...
- Page 12 MULTI-TASKER end of a command string or if the unit ID is [OFFmGkUiS]: for a group of cards zero. This command disables output "m" for each Example: card in group "k" of unit "i". m = card output (m = # from 1-6) [OFF1C2U3F]: if path is not set [OFF1C2U3PF]: if path is set Gk = group number (k = # from 1-9)
-
Page 13: Summary Of Commands
MULTI-TASKER (1-8 for MT100-101 or 1-4 for MT100-106) Example: Example: To group cards #1, 2, and 3 as group 5 of unit #1, send the command [WRC1C2C3G5U1]. To read member data for group 1 of unit 1, After executing this command, cards 1, 2, and 3 send the [RD] command. -
Page 14: Troubleshooting Guide
If the LED is still Solution 3: Call ALTINEX at (714) 990-2300. blinking red, see Solution 3. Cause 2: The MT103-104/(109)(110) card Solution 3: Call ALTINEX at (714) 990- 2300. and its serial device are not communicating. Cause 2: The MT103-104/(109)(110) card... -
Page 15: Altinex Policy
Cause 4. TEL: 714 990-2300 Cause 4: The display has a problem. TOLL FREE: 1-800-ALTINEX Solution 1: Make sure that the display is powered. If there is still no display, WEB: www.altinex.com call ALTINEX at (714) 990-2300. E-MAIL: solutions@altinex.com...