Related Manuals for Altinex MULTI-TASKER MT108-102
Summary of Contents for Altinex MULTI-TASKER MT108-102
- Page 1 MULTI-TASKER MT108-102 is shown above. MANUAL PART NUMBER: 400-0162-002 MT108-102/MT108-103 1-IN, 4-OUT STEREO AUDIO DISTRIBUTION AMPLIFIER CARDS FOR MULTI-TASKER™ USER’S GUIDE...
-
Page 2: Table Of Contents
PRECAUTIONS / SAFETY WARNINGS ... 2 1.1 GENERAL... 2 1.2 INSTALLATION ... 2 1.3 CLEANING... 2 1.4 FCC / CE NOTICE ... 2 ABOUT YOUR MT108-102/(103) ... 3 TECHNICAL SPECIFICATIONS ... 3 DESCRIPTION OF MT108-102/(103) ... 4 APPLICATION DIAGRAM ... 4 INSTALLING YOUR MT108-102/(103)... 6 OPERATION (FOR MT108-103 ONLY) ... -
Page 3: Precautions / Safety Warnings
Please read this manual carefully before using your MT108-102/(103) Distribution Amplifier. Keep this manual handy for future reference. These safety instructions are to ensure the long life of your MT108-102/(103) and to prevent fire and shock hazard. Please read them carefully and heed all warnings. 1.1 GENERAL... -
Page 4: About Your Mt108-102/(103)
ABOUT YOUR MT108-102/(103) MT108-102/(103) 1-in 4-out Stereo Audio Distribution Amplifier Cards The MT108-102 and MT108-103 are Stereo, Audio Distribution Amplifier Cards designed for use with the Multi-Tasker system. When installed in a Multi-Tasker , these cards allow the connection of a single stereo, audio source to four receiving devices. -
Page 5: Description Of Mt108-102/(103)
MULTI-TASKER DESCRIPTION OF MT108-102/(103) APPLICATION DIAGRAM Application 1... - Page 6 MULTI-TASKER Application 2 Internal View of the MT108-102/(103) Card...
-
Page 7: Installing Your Mt108-102/(103)
MT108-102/(103) card is plugged into the Enclosure and note that it is for RS-232 control. OPERATION (for MT108-103 only) 7.1 RS-232 CONTROL The outputs of the MT108-102 are always enabled; therefore, no RS-232 control is necessary. When used Multi-Tasker™... - Page 8 Ui = Unit ID (i = # from 0 to 9) (refer to the MT100-100 user’s guide for explanation) Example: If one MT108-103 card is plugged in slot #2 of unit 3: Sending the command yield following feedback Multi-Tasker™ MT108-103 690-0127-007 MT108-103 = card type 690-0127-007 = software version...
- Page 9 Example: [ON1G5U1]: Turns ON output 1 for each card in group 5 of unit 1. [ONG5U1]: Turns ON all outputs for each card in group 5 of unit 1. [ON…P]: sets path This command will set the path for the output, but it is not active until the switch command, [SW], is executed.
- Page 10 Example: If 2 cards are in slots 6 and 7 of unit 3: To disable outputs 1 and 2 of card 6 and outputs 3 and 4 of card 7 simultaneously, use the following commands: [OFF12C6U3P] [OFF34C7U3P] [SW] If "F" is included use the [OFFmCnUiPF] command or the [OFFmCnUiFP] command.
-
Page 11: Summary Of Commands
14. [G] This command is used to request group data. With the command, the user can identify which input or output of a particular group is on. Command Format: [GkUi] = group number (k = # from 1-9) = unit number (i = # from 0-9) Example: If group 1 has DA Cards with outputs 1 and 2 on, while group 2 has SW Cards with input 2 on:... -
Page 12: Troubleshooting Guide
8.3 SOUND DISTORTION Cause 1: Solution: Cause 2: Solution 1: Make sure that the source signal source correct. Solution 2: Call ALTINEX at (714) 990-2300. MULTI-TASKER The card output is turned OFF. used. RS-232 accessible commands in section 7. If no sound is present, see Solution 2. -
Page 13: Altinex Policy
Note: Test the system by removing the MT108-102/(103) card from between the source and the destination amplifier. If the problem persists, call ALTINEX at (714)-990-2300. MULTI-TASKER ALTINEX POLICY 9.1 LIMITED WARRANTY/RETURN POLICY...