Related Manuals for Altinex MULTI-TASKER MT108-100
Summary of Contents for Altinex MULTI-TASKER MT108-100
- Page 1 MULTI-TASKER MT108-100 is shown above. MANUAL PART NUMBER: 400-0094-005 MT108-100/MT108-101 1-IN, 6-OUT STEREO AUDIO DISTRIBUTION AMPLIFIER CARDS FOR MULTI-TASKER USER’S GUIDE...
-
Page 2: Table Of Contents
7.2 DESCRIPTION OF COMMANDS ....6 7.3 SUMMARY OF COMMANDS....10 TROUBLESHOOTING GUIDE......11 8.2 LED IS BLINKING RED ......11 8.3 NO SOUND ..........11 8.4 SOUND DISTORTION......12 8.5 SOUND LEVEL IS LOW......12 ALTINEX POLICY..........12... -
Page 3: Precautions / Safety Warnings
1.1 GENERAL generates, uses, and can radiate radio frequency energy and, if not installed and • Qualified ALTINEX service personnel, or their used in accordance with the instruction authorized representatives must perform all manual, may cause harmful interference to service. -
Page 4: About Your Mt108-100/(101)
MULTI-TASKER ABOUT YOUR MT108-100/(101) TECHNICAL SPECIFICATIONS MT108-100/MT108-101 FEATURES/DESCRIPTION MT108-100/(101) GENERAL 1-in 6-out Stereo Audio Distribution Inputs Amplifier Cards One 3.5mm stereo mini Input Connector Female audio jack The MT108-100 and MT108-101 are Stereo Audio Outputs Distribution Amplifier Cards designed for use with Left/Right the Multi-Tasker™... -
Page 5: Description Of Mt108-100/(101)
MULTI-TASKER DESCRIPTION OF MT108-100/(101) APPLICATION DIAGRAM Application 1... - Page 6 MULTI-TASKER Application Diagram 2: Internal View of the MT108-100/(101)
-
Page 7: Installing Your Mt108-100/(101)
MULTI-TASKER INSTALLING YOUR MT108-100/(101) 1. Square brackets “[ ]” are part of the command. Step 1. Slide MT108-100/(101) into 2. Use uppercase letters for all commands. available slot in the Multi-Tasker™ Basic After processing a command, an OK or ER string Enclosure in order to connect to the bus. - Page 8 MULTI-TASKER...
- Page 9 MULTI-TASKER = Unit ID number (i = 0 to 9) [ONG5U1]: Turns ON all outputs for each card in group 5 of unit 1. Turns OFF all outputs of the card [OFFCnUi]: [ON...P]: sets path Example: This command will set the path for the output, If card #5 of Unit 3 has outputs 1, 2 and 3 but it is not active until the switch command, [SW], is executed.
- Page 10 MULTI-TASKER other cards in the MT100-100. The system will Example: return feedback as Two (2) cards are in slots 6 and 7 of unit 3. Use the following commands to simultaneously 11. [WR] disable outputs 1 and 2 of card 6 and outputs 3 This command groups multiple cards in the and 4 of card 7.
-
Page 11: Summary Of Commands
MULTI-TASKER will return feedback as 7.3 SUMMARY OF COMMANDS [G1]: [On12G1]. will return feedback as [G2]: [On2G2]. [VER] Receives software version 14. [RD] [Ci] Receives status of the card This command displays the members in each [CiS] Saves card configuration group. -
Page 12: Troubleshooting Guide
If there is still an error, see • 8.3 NO SOUND Solution 3. • 8.4 SOUND DISTORTION Solution 3: Call ALTINEX at (714) 990-2300. • 8.5 SOUND LEVEL IS LOW Cause 2: The MT108-100/(101) and its serial 8.1 LED IS NOT LIT device are not communicating. -
Page 13: Sound Distortion
If there is still (714)-990-2300. no sound, see Solution 2 Solution 2: Set the volume of the destination amplifier to a reasonable level. If there is still no sound, call ALTINEX ALTINEX POLICY at (714) 990-2300. 9.1 LIMITED WARRANTY/RETURN POLICY 8.4 SOUND DISTORTION...
Need help?
Do you have a question about the MULTI-TASKER MT108-100 and is the answer not in the manual?
Questions and answers