Yamaha PM5D Brochure & Specs page 11

PM5D, PM5D-RH Specifications
GENERAL SPECIFICATIONS
All faders are nominal when measured. Output impedance of signal generator:150Ω
Internal Signal Processing 32-bit (Accumulator 58-bit)
Sampling Frequency Internal 44.1kHz, 48kHz, 88.2kHz, 96kHz
External Normal rate: 44.1kHz (-10%) — 48kHz (+6%)
Double rate: 88.2kHz (-10%) — 96kHz (+6%)
Signal Delay Less Than 2.3ms INPUT to STEREO A, B (@ Fs = 48kHz)
Less Than 1.15ms INPUT to STEREO A, B (@ Fs = 96kHz)
Fader Moterized, Stroke: 100mm All Faders
Fader Resolution +10 — -138, -∞dB (1024 steps) All Faders
Total Harmonic Distortion Less Than 0.05 % 20Hz — 20kHz @+4dBu into 600Ω
INPUT 1 — 48 ch to STEREO A,B OUT (@Sampling frequency = 44.1kHz or 48kHz)
Input Gain = Min. Less Than 0.05 % 20Hz — 40kHz @+4dBu into 600Ω
INPUT 1 — 48 ch to STEREO A,B OUT (@Sampling frequency = 96kHz)
Frequency Response PM5D 0.5, -1.5dB 20Hz — 20kHz @1kHz into 600Ω
INPUT 1 — 48 ch to STEREO A,B OUT
(@Sampling frequency = 44.1kHz or 48kHz)
0.5, -2dB 20Hz — 40kHz @1kHz into 600Ω
INPUT 1 — 48 ch to STEREO A,B OUT
(@Sampling frequency = 96kHz)
PM5D-RH 1.0, -3.0dB 20Hz — 20kHz @1kHz into 600Ω
INPUT 1 — 48 ch to STEREO A,B OUT
(@Sampling frequency = 44.1kHz or 48kHz)
1.0, -3.0dB 20Hz — 40kHz @1kHz into 600Ω
INPUT 1 — 48 ch to STEREO A,B OUT
(@Sampling frequency = 96kHz)
Dynamic Range 110 typ. DA Converter (STEREO A, B OUT)
(Max. level to noise level) (@Sampling frequency = 44.1kHz or 48kHz)
108 typ. AD + DA (to STEREO A, B OUT),
GAIN: Min., PAD: ON (@Sampling frequency = 44.1kHz or 48kHz)
110 typ. DA Converter (STEREO A, B OUT) (@Sampling frequency = 96kHz)
106 typ. AD + DA (to STEREO A, B OUT),
GAIN: Min., PAD: ON (@Sampling frequency= 96kHz)
Hum & Noise -128dBu Equivalent Input Noise (20Hz — 20kHz) STEREO A, B OUT
Rs = 150Ω -86dBu Residual Output Noise, ST Master Off.
Input Gain = Max.
Input Pad = 0dB
Input sensitivity = -60dB
Maximum Voltage Gain 84dB INPUT 1 — 48 to STEREO A, B OUT, Rs = 150Ω, Input Gain: Max., PAD: Off
@1kHz 84dB INPUT 1 — 48 to MIX OUT/MATRIX OUT/CUE OUT/MONITOR OUT
(via STEREO Bus)
* Input Gain = Min.
* Hum & Noise is measured with a 6dB/octave filter @12.7kHz; equivalent to a 20kHz filter with infinite
dB/octave attenuation.
* Total Harmonic Distortion is measured with a 18dB/octave filter @80kHz
* Dynamic range is measured with a 6dB/octave filter @12.7kHz; equivalent to a 20kHz filter with infinite
dB/octave attenuation.
ANALOG INPUT CHARACTERISTICS (PM5D)
Actual Load
Input Terminals PAD GAIN For Use With Nominal GAIN SW
Impedance
-60dB
0
INPUT 1 – 48 3kΩ 50-600Ω Mics & 600Ω Lines —
-16dB
26
-34dB
STEREO INPUT 1 – 4 [L, R] 4kΩ 600Ω Lines —
10dB
INSERT IN 1 – 48 10kΩ 600Ω Lines —
+24dB (default)
2TR IN ANALOG 1, 2 [L, R] 10kΩ 600Ω Lines
+18dB
TALKBACK 3kΩ 50-600Ω Mics & 600Ω Lines —
ANALOG INPUT CHARACTERISTICS (PM5D-RH)
Actual Load
Input Terminals GAIN For Use With Nominal GAIN SW
Impedance
-62dB
INPUT 1 – 48 3kΩ 50-600Ω Mics & 600Ω Lines —
+10dB
-62dB 3kΩ
STEREO INPUT 1 – [L, R] 50-600Ω Mics & 600Ω Lines —
+10dB
+24dB (default)
2TR IN ANALOG 1, 2 [L, R] 10kΩ 600Ω Lines
+18dB
TALKBACK 3kΩ 50-600Ω Mics & 600Ω Lines —
*1. Sensitivity is the lowest level that will produce an output of +4dBu (1.23V) or the nominal output level when the unit is set to maximum gain. (All faders and level controls are maximum position.)
*2. XLR-3-31 type connectors are balanced. (1 = GND, 2 = HOT, 3 = COLD)
*3. Phone jacks are balanced. (Tip = HOT, Ring = COLD, Sleeve = GND)
*4. There are switches inside the body to preset the maximum input level.
• In these specifications, 0dBu = 0.775 V rms.
• All input AD converters are 24bit linear, 128times (@48kHz) oversampling.
• +48V DC (phantom power) is supplied to INPUT (1 – 48) XLR type connectors via each individual switch.
Crosstalk -80dB Ajacent Input 1 — 48
@1kHz -80dB Input to Output
Power Requirements PM5D 480W DC 24V 20A (Use PW800W Only)
PM5D-RH 600W DC 24V 25A (Use PW800W Only)
Dimensions W x D x H (mm) 1551 x 950 x 283
Net Weight PM5D: 98 kg, PM5D-RH: 97 kg
Operation free-air Temperature Range 10 — 35 ˚C
Storage Temperature Range -20 — 60 ˚C
LIBRARIES
Name Number
Scene Memory Preset 1 + User 500
Input Patch Library Preset 1 + User 99
Output Patch Library Preset 1 + User 99
Input Channel Library Preset 1 + User 199
Output Channel Library Preset 1 + User 199
Input EQ Library Preset 40 + User 159
Output EQ Library Preset 3 + User 196
GATE Library Preset 4 + User 195
COMP Library Preset 36 + User 163
Effect Library Preset 54 + User 145
GEQ Library Preset 1 + User 199
HA Library Preset 1 + User 199
Input Level
*4
Connector
Sensitivity *1 Nominal Max. Before Clip
-80dBu (0.0775mV) -60dBu (0.775mV) -40dBu (7.75mV)
-36dBu (12.3mV) -16dBu (123mV) +4dBu (1.23V) XLR-3-31 Type (Balanced)
-10dBu (245mV) +10dBu (2.45V) +30dBu (24.51V)
-54dBu (1.55mV) -34dBu (15.5mV) -14dBu (155mV)
XLR-3-31 Type (Balanced)
-10dBu (245mV) +10dBu (2.54V) +30dBu (24.51V)
-16dBu (123mV) +4dBu (1.23V) +24dBu (12.28V) Phone Jack (TRS) (Balanced)
-6dBu (388mV) +4dBu (1.23V) +24dBu (12.28V)
XLR-3-31 Type (Balanced)
-12dBu (195mV) -2dBu (0.616V) +18dBu (6.16V)
-60dBu (0.775mV) -50dBu (2.45mV) -30dBu (24.5mV) XLR-3-31 Type (Balanced)
Input Level
*4 Connector
Sensitivity *1 Nominal Max. Before Clip
-82dBu (61.6µV) -62dBu (0.616mV) -42dBu (6.16mV)
XLR-3-31 Type (Balanced)
-10dBu (245mV) +10dBu (2.45V) +30dBu (24.5V)
-82dBu (61.6µV) -62dBu (0.616mV) -42dBu (6.16mV)
XLR-3-31 Type (Balanced)
-10dBu (245mV) +10dBu (2.45V) +30dBu (24.5V)
-6dBu (388mV) +4dBu (1.23V) +24dBu (12.28V)
XLR-3-31 Type (Balanced)
-12dBu (195mV) -2dBu (0.616V) +18dBu (6.16V)
-60dBu (0.775mV) -50dBu (2.45mV) -30dBu (24.5mV) XLR-3-31 Type (Balanced)
ANALOG OUTPUT CHARACTERISTICS
Actual Source
Output Terminals
Impedance
STEREO A, B [L, R]
MONITOR OUT [L, R, C]
CUE OUT [L, R]
MATRIX OUT 1 – 8
MIX OUT 1 – 24
INSERT OUT 1 – 48
PHONES (x2)
DIGITAL INPUT CHARACTERISTICS
Total
501
Terminal Format
100
2TR IN 1 AES/EBU AES/EBU
100
DIGITAL 2 AES/EBU
AES/EBU
200
(*2)
3 COAXIAL IEC-60958
200
CASCADE IN —
199
199
*1. XLR-3-31 type connectors are balanced. (1 = GND, 2 = HOT, 3 = COLD)
199 *2. With Sampling Rate Converter
199
199
200
SLOT (1-4) CHARACTERISTICS
200
Each I/O SLOT accepts a Digital Interface card.
Only SLOT1 has a Serial Interface.
Card Name Function Input
MY4-AD ANALOG IN 4 IN
MY8-AD24 ANALOG IN 8 IN
MY8-AD96 ANALOG IN 8 IN
MY4-DA ANALOG OUT —
MY8-DA96 ANALOG OUT —
MY8-AE96 AES/EBU 8 IN
MY8-AE96S AES/EBU 8 IN
MY8-AT ADAT 8 IN
MY8-TD TASCAM 8 IN
MY8-AE AES/EBU 8 IN
MY16-AT ADAT 16 IN
MY16-TD TASCAM 16 IN
MY16-AE AES/EBU 16 IN
MY16-C CobraNet ™ 16 IN
*2
Dimensions
*2
*3
PM5D
*2
*2
*2
*2
*2
*2
1450
1551
Output Level
For Use With Nominal GAIN SW *4
Nominal Max. Before Clip
+24dB (default) +4dBu (1.23 V) +24dBu (12.28 V)
150Ω 600Ω Lines
+18dB -2dBu (616mV) +18dBu (6.16V)
+24dB (default) +4dBu (1.23 V) +24dBu (12.28 V)
150Ω 600Ω Lines
+18dB -2dBu (616mV) +18dBu (6.16V)
+24dB (default) +4dBu (1.23 V) +24dBu (12.28 V)
150Ω 600Ω Lines
+18dB -2dBu (616mV) +18dBu (6.16V)
150Ω 600Ω Lines +24dB (default) +4dBu (1.23 V) +24dBu (12.28 V)
+18dB -2dBu (616mV) +18dBu (6.16V)
150Ω 600Ω Lines +24dB (default) +4dBu (1.23 V) +24dBu (12.28 V)
+18dB -2dBu (616mV) +18dBu (6.16V)
150Ω 10kΩ Lines — +4dBu (1.23 V) +24dBu (12.28 V)
15Ω 8Ω Phones — 75mW (*6) 150mW
40É∂ Phones — 65mW (*6) 150mW
DIGITAL OUTPUT CHARACTERISTICS
Data Length Level Connector Terminal
24bit RS422 XLR-3-31 Type (Balanced) *1 2TR OUT
1 AES/EBU
DIGITAL
24bit RS422 XLR-3-31 Type (Balanced) *1
(*3)
24bit 0.5Vpp/75Ω RCA Pin Jack 2 AES/EBU
— RS422 D-Sub Half Pitch Connector 68P (Female)
3 COAXIAL
CASCADE OUT
*1. Dither :word length 16/20/24 bit
*2. XLR-3-32 type connectors are balanced. (1 = GND, 2 = HOT, 3 = COLD)
*3. With Sampling Rate Converter
The Number Of
Output
Usable Cards
— 4
— 4
— 4
4 OUT (MIX, STEREO, DIRECT, EXT INSERT, MONIOTR, CUE, OSC, TB) 4
8 OUT (MIX, STEREO, DIRECT, EXT INSERT, MONIOTR, CUE, OSC, TB) 4
8 OUT (MIX, STEREO, DIRECT, EXT INSERT, MONIOTR, CUE, OSC, TB) 4
8 OUT (MIX, STEREO, DIRECT, EXT INSERT, MONIOTR, CUE, OSC, TB) 4
8 OUT (MIX, STEREO, DIRECT, EXT INSERT, MONIOTR, CUE, OSC, TB) 4
8 OUT (MIX, STEREO, DIRECT, EXT INSERT, MONIOTR, CUE, OSC, TB) 4
8 OUT (MIX, STEREO, DIRECT, EXT INSERT, MONIOTR, CUE, OSC, TB) 4
16 OUT (MIX, STEREO, DIRECT, EXT INSERT, MONIOTR, CUE, OSC, TB) 4
16 OUT (MIX, STEREO, DIRECT, EXT INSERT, MONIOTR, CUE, OSC, TB) 4
16 OUT (MIX, STEREO, DIRECT, EXT INSERT, MONIOTR, CUE, OSC, TB) 4
16 OUT (MIX, STEREO, DIRECT, EXT INSERT, MONIOTR, CUE, OSC, TB) 4
PM5D-RH
283
271
260
*1. XLR-3-32 type connectors are
Connector
balanced. (1 = GND, 2 = HOT,
3 = COLD)
*2. Phone jack are balanced.
*1
XLR-3-32 Type (Balanced)
(Tip = HOT, Ring = COLD,
Sleeve = GND)
XLR-3-32 Type (Balanced) *1 *3. PHONES stereo phone jack is
unbalanced. (Tip = LEFT,
Ring = RIGHT, Sleeve = GND)
*1
XLR-3-32 Type (Balanced)
*4. There are switches inside the
body to preset the maximum
output level.
XLR-3-32 Type (Balanced) *1
*5. INSERT OUTs are only provided
for PM5D
*1 *6. The position of the level control is
XLR-3-32 Type (Balanced)
10dB lowered from Max.
Phone Jack (TRS) (Balanced) *2 *5 • In these specifications,
0dBu = 0.775 Vrms.
Stereo Phone Jack (TRS)
• All output DA converters are 24bit,
*3
(Unbalanced)
128times (@48kHz) oversampling.
Format Data Length Level Connector
AES/EBU
24bit *1 RS422 XLR-3-32 Type (Balanced) *2
Professional Use
AES/EBU
24bit *1 XLR-3-32 Type (Balanced) *2
Professional Use
IEC-60958
24bit *1 0.5Vpp/75Ω RCA Pin Jack
Consumer Use
— — RS422 D-Sub Half Pitch Connector 68P (Female)
PW800W Specifications
GENERAL SPECIFICATIONS
Power Requirements 100 – 240V, 50/60Hz
1000W (Max.)
Dimensions W x H x D (mm) 480 x 132 (=3U) x 355
DC Output Voltage 24V
Current 23A (Max.)
Net Weight 10 kg
10 – 35 °C
Operation Temperature Range
-20 – 60 °C
Storage Temperature Range
OUTPUT CHARACTERISTICS
OUTPUT TERMINAL FORMAT LEVEL CONNECTOR
DC OUTPUT — DC 24V JL05-2A22-14PC 24pin (Male)
Specifications and appearance are subject to change without notice.
All trademarks and registered trademarks are property of their respective owners.
283
271
260
1450
1551