Related Manuals for Christie 38-FP0001-01
Summary of Contents for Christie 38-FP0001-01
- Page 1 38-FP0001-01 MODEL (with Video Card) 38-FP0001-02 (without Video Card) User's Manual...
-
Page 2: Table Of Contents
Table of contents Precautions ....................2 Before First Use Names and Functions (Monitor) ............3-4 Check Accessories ................. 3 Outer Dimension.................. 5-6 Installation ................... 7-8 Names and Functions (Remote Controller) ........9-10 Preparation for remote control .............. 11 LCD Monitor Instructions Adjusting the Screen................ -
Page 3: Precautions
Precautions Important matters • Plug the included AC Power Cord to the power supply and voltage as mentioned in the rating label. IF NOT, DAMAGE TO THE AC POWER CORD IS A SAFETY RISK AND CAN CAUSE A FIRE. Placement precautions •... -
Page 4: Before First Use
Before First Use Names and Functions (Monitor) Front View Display Screen NOTE ¡ When you move the LCD monitor, please unplug AC cables connected to AC-IN and disconnect the cables connected to the external equipment. ¡ When you carry the LCD monitor, please be careful not to shock it. To avoid damaging the LCD panel, be sure not to touch the LCD panel when carrying the monitor. -
Page 5: Rear View
Rear View Ventilators Ventilators Ventilators RGB Connector DVI Connector External Control Power Switch ( Connector Turns the power to the monitor on and off. AC-IN... -
Page 6: Outer Dimension
Before First Use Outer Dimension Ventilators POWER External Control AC-IN... - Page 7 Ventilators Ventilators Ventilators 4-M6 (Depth : Min.12mm/Max.20mm) Ventilators Ventilators Mounting Area Ventilators Ventilators When you install the LCD Monitor, please take care the following: • Use the M6 screws only for installation. • The maximum length of the screw put through a L: 12mm(min.) 20mm(max.) hole is 20mm on the surface of a metal chassis...
-
Page 8: Installation
Before First Use Installation Connect the Computers Before doing anything, make sure the Power Switch on the monitor and a computer is turned off. Plug the cable(s) into the connector on the monitor securely and fix them in place with two screws (each). Plug the other end of the cable(s) into the connector on a computer. - Page 9 How to secure the monitor on a wall Note: The following figure is only recommended. M6 bolt (4 places) Vertical Depth: Min. 12mm Max. 20mm Bracket (not included) Side view of the monitor Rear view of the monitor Horizontal M6 bolt (4 places) Depth: Min.
-
Page 10: Names And Functions (Remote Controller)
Before First Use Names and Functions (Remote Controller) Operating Range (when there is no obstacle) Horizontal Vertical... - Page 11 Standby key Standby ON/OFF. Menu key Show Main menu. Used to move cursor leftward while displaying the menu. Wide key Set the scale mode in wide. Numeric keys (see page 72) Used to switch each input signal. [0], [8] and [9] keys are not used. [1] Analog RGB1 selection [2] Digital RGB selection [3] Composite VIDEO selection...
-
Page 12: Preparation For Remote Control
Before First Use Preparation for remote control Remove the battery compartment lid with pushing O P E N Be sure and put two AA dry batteries into the remote controller. Make sure of the direction of them as indicated inside the remote controller. -
Page 13: Lcd Monitor Instructions
LCD Monitor Instructions Adjusting the Screen This LCD monitor decodes the signal from a computer automatically, and displays the image on a screen in accordance with the preset mode. Unless a display mode has been in preset table, the image is displayed under the similar mode in preset table. In this case, the adjustment for this LCD monitor must be done in accordance with a computer connected with. -
Page 14: Adjustment Items
LCD Monitor Instructions Adjustment Items Adv pip(Advanced picture in picture) Menu (refer to page 29-30) H POSITION Select the horizontal position of pip V POSITION Select the vertical position of pip VIDEO FORMAT Select the video format (ntsc/pal/secam) Note Adv pip Menu can be used when inputting Composite Video or S-Video signal and also selecting [small] or [medium] or [large] in [size] menu. -
Page 15: Mode
Mode You can change or indicate the signal input type following the steps. Change or indicate the input signal While the OSD (On Screen Display) is not displayed, it is possible to change or indicate the current mode. Press [Source] key to indicate the current mode in the lower right corner of the screen. -
Page 16: Adjustment Procedure
LCD Monitor Instructions Adjustment Procedure Before Adjustment The signal timing for a computer which this LCD monitor supports is listed in "Table of Preset Data" on Page 39, the recommended value of Vertical Frequency for this model is 60Hz. (Unlike CRT Monitors, the display becomes stable when Vertical Frequency is low.) It is recommend to set Vertical Frequency of a computer connected at 60Hz by "refresh rate setting"... - Page 17 Move the cursor to Sub menu After Main menu item is selected, press [Menu ] key. Press [ Menu] key to return to Main menu from Sub menu. Brightness Picture Contrast Advanced H position V position (Ex.) Adv pip Phase Options Frequency 1056...
- Page 18 LCD Monitor Instructions Adjustment Procedure For the adjustment item like "brightness", press [ ] or [ ] key to change levels of selected item. Brightness Picture Contrast Advanced H position V position (Ex.) Adv pip Phase Options Frequency 1056 Utilities Scaling Wide Main menu...
-
Page 19: Adjustment For Computer Screen
Adjustment for computer screen (Picture Menu) Manual Adjustment If you wish to adjust the screen finely or in case the result adjusted by Auto Adjust (see page 34) sequence is not sufficient enough, adjust the screen manually. A. Picture Menu Adjust the brightness Select [Picture] on the Main menu and press [Menu ] key. - Page 20 LCD Monitor Instructions Adjustment Procedure (Picture Menu) Use [ ] and/or [ ] key to adjust. (Interval: 0~100) By pressing [ ] key, the contrast (difference between bright and dark) becomes darker. By pressing [ ] key, the contrast (difference between bright and dark) becomes lighter.
-
Page 21: Adjustment For Computer Screen
Adjustment for computer screen Select [V position] on the Sub menu with pressing [ ] or [ ] key. The selected item of [V position] turns blue. Use [ ] and/or [ ] key to adjust. (Interval: 0~100) Press [ ] key to shift the screen to the top. - Page 22 LCD Monitor Instructions Adjustment Procedure (Picture Menu) Use [ ] and/or [ ] key to adjust. By pressing [ ] key, the horizontal width becomes wider. By pressing [ ] key, the horizontal width becomes narrower. Adjust the scaling Select [Picture] on the Main menu and press [Menu ] key.
-
Page 23: Advanced Menu
Adjustment for computer screen (Advanced Menu) B. Advanced Menu You can adjust the color temperature for the screen manually. Three preset values of color temperature are set up at the time of factory shipments. Besides, you can set your preferable values. Adjust the color temperature (Preset) Select [Advanced] on the Main menu and press [Menu ] key. - Page 24 LCD Monitor Instructions Adjustment Procedure (Advanced Menu) Color Warm Neutral Cold user User red Picture User green Advanced User blue (Ex.) Sub menu Adv pip Options Utilities Main menu Select [Color] on the Sub menu with pressing [ ] or [ ] key.
-
Page 25: Picture In Picture Menu
Adjustment for computer screen (Pip Menu) C. Picture in picture Menu If you wish to adjust a pip(picture in picture), you can adjust the size, position, source, brightness, contrast, color, tint and sharpness manually. Adjust the size Select [Pip] on the Main menu and press [Menu ] key. - Page 26 LCD Monitor Instructions Adjustment Procedure (Pip Menu) Select [Pos] on the Sub menu with pressing [ ] or [ ] key. The selected item of [Pos] turns blue. Use [ ] and/or [ ] key to select the position. When pressing [ ] key, the position of pip(picture in picture) can be selected according to the order in sequence.
-
Page 27: Adjustment For Computer Screen
Adjustment for computer screen Adjust the brightness (Video signal only) You can adjust this item when selecting [small] or [medium] or [large] in [Size] menu (see page 24). Select [Pip] on the Main menu and press [Menu ] key. You can see the cursor moving to the Sub menu. Size small medium large... - Page 28 LCD Monitor Instructions Adjustment Procedure (Pip Menu) Use [ ] and/or [ ] key to adjust. (Interval: 0~100) By pressing [ ] key, the contrast (difference between bright and dark) becomes darker. By pressing [ ] key, the contrast (difference between bright and dark) becomes lighter.
-
Page 29: Adjustment For Computer Screen
Adjustment for computer screen Size small medium large Picture Advanced Source auto comp s-video Brightness (Ex.) Adv pip Contrast Options Color Utilities Tint Main menu Sharpness Sub menu Select [Tint] on the Sub menu with pressing [ ] or [ ] key. -
Page 30: Advanced Picture In Picture Menu
LCD Monitor Instructions Adjustment Procedure ( Advanced Pip Menu D. Advanced picture in picture Menu This menu can be used when inputting Composite Video or S-Video signal and also selecting [small] or [medium] or [large] in [Size] menu (see page 24). You can adjust the horizontal/vertical position for pip and select the video format if you select this menu. -
Page 31: Adjustment For Computer Screen
Adjustment for computer screen Use [ ] and/or [ ] key to adjust. (Interval: 0~100) Press [ ] key to shift the screen to the bottom. Press [ ] key to shift the screen to the top. Select the video format Select [Adv pip] on the Main menu and press [Menu ] key. -
Page 32: Options Menu
LCD Monitor Instructions Adjustment Procedure (Options Menu) E. Options Menu You can change the osd position, osd timeout, osd background and backlight and select portrait or landscape, language used in osd and see the resolution at the time if you select this menu. Select the osd position Select [Options] on the Main menu and press [Menu ] key. - Page 33 Adjustment for computer screen Use the [ ] and/or [ ] key to select [Normal] or [Rotated]. Select "Normal" to display LANDSCAPE. Select "Rotated" to display PORTRAIT. Change the osd timeout Select [Options] on the Main menu and press [Menu ] key.
-
Page 34: E. Options Menu
LCD Monitor Instructions Adjustment Procedure (Options Menu) Select language used in OSD (On Screen Display) Select [Options] on the Main menu and press [Menu ] key. You can see the cursor moving to the Sub menu. Rotation Normal Rotated Picture Osd timeout 10 seconds Advanced... -
Page 35: Utilities Menu
Adjustment for computer screen (Utilities Menu) F. Utilities Menu You can adjust the screen by Auto Adjust (Automatic Adjustment), reset the osd setting, and display the osd version if you select this menu. Automatic Adjustment (Analog mode only) Select [Utilities] on the Main menu and press [Menu ] key. - Page 36 LCD Monitor Instructions Adjustment Procedure (Utilities Menu) Display the osd version Select [Utilities] on the Main menu, the osd version is always displayed in [Internal Firmware] on the Sub menu. Auto Adjust press <right> to select Picture Reset Internal Firmware Rom Version Advanced 1024 x 768 / 60 Hz Mode: 88...
-
Page 37: Additional Functions
Additional Functions Power Management System This is the function to reduce the monitor's power consumption, when a computer has not been used for long, even when the power to this LCD monitor is "ON". In order to activate this system, it must be connected and used with a computer that conforms to DPMS (Display Power Management Signaling) Standard of the VESA (Video Electronics Standards Association). -
Page 38: Maintenance
Maintenance Always unplug the AC cable from the outlet before maintenance. Also unplug the signal cables from the computer. Soak a soft cloth in water or neutral detergent, wring well, and wipe the cabinet gently. Never use solvents such as Cabinet paint thinner or benzene as they will damage the surface of the cabinet. -
Page 39: Troubleshooting
Troubleshooting Fault Finding Please check the following items before requesting repair. When this LCD monitor still does not work properly after checking in following way, stop using it, turn off the power switch, unplug the power plug from the AC Outlet, and contact the store where it was purchased. -
Page 40: Specifications
Specifications Table of Preset Data Fifteen signal timing patterns indicated in the tables below are preset when the monitor is shipped from the factory. The timing pattern is automatically determined and displayed according to the synchronous signals of the computer being used. The monitor will use the closest timing pattern for display when a perfectly matched one is not available. -
Page 41: Cable Pin Arrangement
Cable Pin Arrangement Analog Video Input : mini D-Sub (15pin) Signal name Signal name Signal name R GND No Connect G GND DDC data line* B GND Hor. Sync. No Connect No Connect Vert. Sync. DDC GND* DDC clock line* * DDC Standard (VESA) Cable Pin Arrangement (female) Digital Video Input : DVI-D (24pin) -
Page 42: Monitor Specifications
Specifications Monitor Specifications Liquid Crystal Panel Display Size 39.6'' Pixel Configuration 1,280 x 768 Pixel Pitch 0.6735 x 0.6735 mm Brightness 470 cd/m typ. Response Time Black to White: 14 ms White to Black: 8 ms Gray to Gray: 8 ms Contrast 600 : 1 typ. -
Page 43: Table Of Contents
Adjustment for Composite Video/S-Video/Component Video Table of contents Table of contents ..................42 Before First Use Names and Functions..............43-46 Outer Dimension................47,48 Installation ..................49-51 How to Use ................... 52 Adjustment for Composite Video / S-Video / Component Video Adjustment Items .................. -
Page 44: Names And Functions
Adjustment for Composite Video/S-Video/Component Video Names and Functions (Monitor) Front View Display Screen NOTE ¡ When you move the LCD monitor, please unplug AC cables connected to AC-IN and disconnect the cables connected to the external equipment. ¡ When you carry the LCD monitor, please be careful not to shock it. To avoid damaging the LCD panel, be sure not to touch the LCD panel when carrying the monitor. - Page 45 Rear View Connector B/Cb R/Cr Ventilators Ventilators Ventilators RGB Connector DVI Connector External Control Power Switch ( Connector Turns the power to the monitor on and off. S-Video Connector AC-IN Composite Video Connector...
- Page 46 Adjustment for Composite Video/S-Video/Component Video Names and Functions (Remote Controller) Operating Range (when there is no obstacle) Horizontal Vertical...
- Page 47 Standby key Standby ON/OFF. Menu key Show Main menu. Used to move cursor leftward while displaying the menu. Wide key Set the scale mode in wide. Numeric keys (see page 72) Used to switch each input signal. [0], [8] and [9] keys are not used. [1] Analog RGB1 selection [2] Digital RGB selection [3] Composite VIDEO selection...
-
Page 48: Outer Dimension
Adjustment for Composite Video/S-Video/Component Video Outer Dimension Ventilators HD/CSYNC B/Cb R/Cr VIDEO S-VIDEO POWER AC-IN External Control... - Page 49 Ventilators Ventilators Ventilators 4-M6 (Depth : Min.12mm/Max.20mm) Ventilators Ventilators Mounting Area Ventilators Ventilators When you install the LCD Monitor, please take care the following: • Use the M6 screws only for installation. • The maximum length of the screw put through a L: 12mm(min.) 20mm(max.) hole is 20mm on the surface of a metal chassis...
-
Page 50: Installation
Adjustment for Composite Video/S-Video/Component Video Installation Connect the Video deck, DVD player etc. Turn off the power for the monitor and AV equipment before the connection. Plug the cable(s) into the connector on the monitor securely. Plug the other end of the cable(s) into the connector on AV equipment. - Page 51 Connect the Computers Before doing anything, make sure the Power Switch on the monitor and a computer is turned off. Plug the cable(s) into the connector on the monitor securely and fix them in place with two screws (each). Plug the other end of the cable(s) into the connector on a computer. Plug the AC Power Cord into the AC-IN on the monitor.
- Page 52 Adjustment for Composite Video/S-Video/Component Video Installation How to secure the monitor on a wall Note: The following figure is only recommended. M6 bolt (4 places) Vertical Depth: Min. 12mm Max. 20mm Bracket (not included) Side view of the monitor Rear view of the monitor Horizontal M6 bolt (4 places) Depth: Min.
-
Page 53: How To Use
How to Use Use this monitor with following procedure. Watch Video/DVD Use Computers Connect video cable from Connect video cable from Video computer to this monitor. deck or DVD player to the monitor. Choose "Composite Video" or Choose "Analog" or "Digital" "S-Video"... -
Page 54: Adjustment For Composite Video/S-Video/Component Video
Adjustment for Composite Video/S-Video/Component Video Adjustment Items Please follow the OSD (On Screen Display) menu to adjust screen settings using Remote Controller (see page 45). Adjustment Items for Composite Video, S-Video and Component Video screen Picture Menu (refer to page 58-62) BRIGHTNESS Adjust the brightness for video screen CONTRAST... -
Page 55: Mode
Mode You can change or indicate the signal input type following the steps. Change or indicate the input signal While the OSD (On Screen Display) is not displayed, it is possible to change or indicate the current mode. Press [Source] key to indicate the current mode in the lower right corner of the screen. -
Page 56: Adjustment Procedure
Adjustment for Composite Video/S-Video/Component Video Adjustment Procedure Before Adjustment The signal timing for a computer which this LCD monitor supports is listed in "Table of Preset Data" on Page 39, the recommended value of Vertical Frequency for this model is 60Hz. (Unlike CRT Monitors, the display becomes stable when Vertical Frequency is low.) It is recommend to set Vertical Frequency of a computer connected at 60Hz by "refresh rate setting"... - Page 57 Move the cursor to Sub menu After Main menu item is selected, press [Menu ] key. Press [ Menu] key to return to Main menu from Sub menu. Brightness Picture Contrast Advanced H position V position (Ex.) Adv pip Phase Options Frequency 1056...
- Page 58 Adjustment for Composite Video/S-Video/Component Video Adjustment Procedure For the adjustment item like "brightness", press [ ] or [ ] key to change levels of selected item. Brightness Picture Contrast Advanced H position V position (Ex.) Adv pip Phase Options Frequency 1056 Utilities Scaling...
-
Page 59: Picture Menu
(Picture Menu) A. Picture Menu The adjustment of brightness, contrast, horizontal position, vertical position, color, tint, sharpness and scaling for the picture are available. Adjust the brightness Select [Picture] on the Main menu and press [Menu ] key. You can see the cursor moving to the Sub menu. Brightness Contrast Picture... - Page 60 Adjustment for Composite Video/S-Video/Component Video Adjustment Procedure (Picture Menu) Use [ ] and/or [ ] key to adjust. (Interval: 0~100) By pressing [ ] key, the contrast (difference between bright and dark) becomes lighter. By pressing [ ] key, the contrast (difference between bright and dark) becomes darker.
-
Page 61: Adjust The Color
Select [V position] on the Sub menu with pressing [ ] or [ ] key. The selected item of [V position] turns blue. Use [ ] and/or [ ] key to adjust. (Interval: 0~100) By press [ ] key to shift the screen to the top. By press [ ] key to shift the screen to the bottom. - Page 62 Adjustment for Composite Video/S-Video/Component Video Adjustment Procedure (Picture Menu) Select [Tint] on the Sub menu with pressing [ ] or [ ] key. The selected item of [Tint] turns blue. Use [ ] and/or [ ] key to adjust. (Interval: 0~100) By pressing [ ] key, the skin color becomes more greenish.
- Page 63 Adjust the scaling Select [Picture] on the Main menu and press [Menu ] key. You can see the cursor moving to the Sub menu. Brightness Contrast Picture H position Advanced (Ex.) V position Video Color Options Tint Utilities 1 2 3 4 5 6 7 8 Sharpness Main menu Scaling...
-
Page 64: Advanced Menu
Adjustment for Composite Video/S-Video/Component Video Adjustment Procedure (Advanced Menu) B. Advanced Menu You can adjust the color temperature for the screen manually if you select this menu. Three preset values of color temperature are set up at the time of factory shipments. Besides, you can set your preferable values. - Page 65 Adjust the color temperature (User) If you wish to set user settings of color temperature, follow the steps. (Ex.) In case adjusting the [User red], [User green] and [User blue] in sequence. Select [Advanced] on the Main menu and press [Menu ] key.
-
Page 66: Video Menu
Adjustment for Composite Video/S-Video/Component Video Adjustment Procedure (Video Menu) C. Video Menu When video signal is input, you can select the video format (NTSC/PAL/SECAM) manually. Select the video format Select [Video] on the Main menu and press [Menu ] key. You can see the cursor moving to the Sub menu. -
Page 67: Options Menu
(Options Menu) D. Options Menu You can change the osd position, osd timeout, osd background and backlight and select portrait or landscape, language used in osd and see the resolution at the time if you select this menu. Select the osd position Select [Options] on the Main menu and press [Menu ] key. - Page 68 Adjustment for Composite Video/S-Video/Component Video Adjustment Procedure (Options Menu) Use the [ ] and/or [ ] key to select [Normal] or [Rotated]. Select "Normal" to display LANDSCAPE. Select "Rotated" to display PORTRAIT. Change the osd timeout Select [Options] on the Main menu and press [Menu ] key.
- Page 69 Select language used in OSD (On Screen Display) Select [Options] on the Main menu and press [Menu ] key. You can see the cursor moving to the Sub menu. Picture Rotation Normal Rotated Osd timeout Advanced 10 seconds (Ex.) Osd background opaque translucent Video Options...
-
Page 70: Utilities Menu
Adjustment for Composite Video/S-Video/Component Video Adjustment Procedure (Utilities Menu) E. Utilities Menu You can reset the osd setting and display the osd version if you select this menu. Delete the data saved at the current display mode Select [Utilities] on the Main menu and press [Menu ] key. -
Page 71: Additional Functions
Additional Functions Shortcut Menu You can shortcut to adjust the brightness and contrast of the whole screen and size of picture in picture. When the OSD (On Screen Display) is not displayed, it is possible to display the Shortcut Menu. The adjustment flow is described in below: Display the Shortcut Menu While the OSD (On Screen Display) is not displayed, it is possible to display the Shortcut Menu. - Page 72 Adjustment for Composite Video/S-Video/Component Video Additional Functions Use [ ] and/or [ ] key to adjust. (Interval: 0~100) By pressing [ ] key, the contrast (difference between bright and dark) becomes darker. By pressing [ ] key, the contrast (difference between bright and dark) becomes lighter.
-
Page 73: Zoom Menu
To search other input signal connected to the monitor, press [Source] key of remote control again while the input signal type is displayed. The searching order of other input signal is as follows. [Analog RGB1] [Analog RGB2] [Digital RGB] [Composite Video] [S-Video] [Component Video] [RGB+C Sync]... -
Page 74: Power Management System
Adjustment for Composite Video/S-Video/Component Video Additional Functions Power Management System This is the function to reduce the monitor's power consumption, when a computer has not been used for long, even when the power to this LCD monitor is "ON". In order to activate this system, it must be connected and used with a computer that conforms to DPMS (Display Power Management Signaling) Standard of the VESA (Video Electronics Standards Association). -
Page 75: Troubleshooting
Troubleshooting Fault Finding Fault Finding Please check the following items before requesting repair. When this LCD monitor still does not work properly after checking in following way, stop using it, turn off the power switch, unplug the power plug from the AC Outlet, and contact the store where it was purchased. -
Page 76: Specifications
Specifications Monitor Specifications Liquid Crystal Panel Display Size 39.6'' Pixel Configuration 1,280 x 768 Pixel Pitch 0.6735 x 0.6735 mm Brightness 470 cd/m typ. Response Time Black to White: 14 ms White to Black: 8 ms Gray to Gray: 8 ms Contrast 600 : 1 typ. - Page 77 Federal Communications Commission (FCC) Statement This device has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 80 CHRISTIE DIGITAL SYSTEMS, Inc. CHRISTIE DIGITAL SYSTEMS, Inc. CHRISTIE DIGITAL SYSTEMS, Inc. CHRISTIE DIGITAL SYSTEMS, Inc. CHRISTIE DIGITAL SYSTEMS, Inc. 809 Wellington Street North 10550 Camden Drive ViewPoint Willicher Damm 129 627A Aljunied Road D-41066 M nchengladbach Germany Kitchener, Ontario...