1. Manuals
  2. Brands
  3. Hunter Manuals
  4. Fan
  5. Type 3 Models
  6. Installation and operation manual

Hunter TYPE 3 Models Installation And Operation Manual

Ceiling fans
Hide thumbs Also See for TYPE 3 Models:
Table of Contents

Advertisement

Quick Links

See also: Owner's Manual & Installation Manual , Instruction and Installation Manual
For Your Records and Warranty
Assistance
Model Name: _____________________
Catalog/Model No.: ________________
Serial No.: ________________________
Date Purchased: ___________________
Where Purchased: _________________
For reference also attach your receipt or a
copy of your receipt to the manual.
installation and
operation manual
for Hunter
Ceiling Fans
TYPE 3 Models
42753-01 • 06/11/07

Advertisement

Table of Contents
loading

Related Manuals for Hunter TYPE 3 Models

Summary of Contents for Hunter TYPE 3 Models

  • Page 1 For Your Records and Warranty Assistance Ceiling Fans Model Name: _____________________ Catalog/Model No.: ________________ Serial No.: ________________________ Date Purchased: ___________________ Where Purchased: _________________ TYPE 3 Models For reference also attach your receipt or a copy of your receipt to the manual. 42753-01 • 06/11/07...

  • Page 2: Table Of Contents

    • To reduce the risk of fire, electrical shock, or motor damage, do not 10 • Operating the Remote Control and Mounting the Holder ....15 use a solid-state speed control with this fan. Use only Hunter speed controls. 11 • Operating and Cleaning Your Ceiling Fan .........
  • Page 3 Support Brace Hunter’s patented 3-position mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of three ways, depending on ceiling height and your preference: Low Profile, Standard, or Angle mounting. The steps in this manual include Ceiling instructions for all three Installer’s Choice mounting methods.

  • Page 4: Getting Ready

    • Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: •...

  • Page 5: Installing The Ceiling Plate

    Do not over tighten. Flat Washer 3” Wood Screw For Angled Ceilings: Be sure to orient the ceiling plate so that the arrows printed on the ceiling plate are pointing towards the ceiling peak. 42753-01 • 06/11/07 • Hunter Fan Company...

  • Page 6: Assembling And Hanging The Fan

    Assemble securely with three low profile screws. 3-7. Raise the fan and place the hook on the ceiling plate through the U-shaped hole in the rim. Low Profile Screw Step 3-7 U-shaped Hole 42753-01 • 06/11/07 • Hunter Fan Company...

  • Page 7: Support System

    4-8. Return to the fan so you can complete the fan wiring. Step 4-1 Steps 4-6 – 4-7 Steps 4-2 – 4-3 Steps 4-4 – 4-5 3mm (1/8") Support Brace Outlet Box Braided Ceiling Cable 42753-01 • 06/11/07 • Hunter Fan Company...

  • Page 8: Setting The Remote Transmitter And Receiver

    CAUTION: The remote control device complies with part 15 of the FCC rules. Changes or modifications not expressly approved by Hunter Fan Company could void your authority to operate this equipment. Operation is subject to the following two conditions: 1.

  • Page 9: Wiring The Fan

    6-7. Run the white antenna wire from the receiver through one of the Small Wire slots in the ceiling plate so that it rests between the ceiling plate Connector and the ceiling. Push it to the edge of the ceiling plate for clear reception. 42753-01 • 06/11/07 • Hunter Fan Company...

  • Page 10: Installing The Canopy And Canopy Trim Ring

    2. Press firmly on opposite sides of the ring towards the canopy. The tabs will flex out releasing the trim ring from the canopy. Step 7-3 Steps 7-4 – 7-5 Canopy Screw 42753-01 • 06/11/07 • Hunter Fan Company...

  • Page 11: Assembling The Blades

    8 • Assembling the Blades Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan). 8-1. Your fan may include blade grommets. If your fan has grommets, Step 8-1 (Detail) insert them by hand into the holes on the blades.

  • Page 12: Completing Your Installation With A Light Fixture

    9 • Completing Your Installation With a Bowl Light Fixture Your Hunter fan comes with an integrated light fixture assembly. WARNING: Use only the light fixture supplied with this fan model. 9-1. To attach the upper switch housing, partially install two housing assembly screws into the switch housing mounting plate.
  • Page 13 Align the side screw holes in the upper and lower switch housings. Attach the lower switch housing to the upper switch housing with three housing assembly screws. Lower Switch Housing Plug Connector Detail Housing Assembly Screw 42753-01 • 06/11/07 • Hunter Fan Company...
  • Page 14 9-9. Screw the finial onto the threaded rod end until tight. Light Bulbs (B10 Candelabra Base 60 Watt Maximum) Metal Rod Metal Disk Glass Bowl Cover Plate Finial 42753-01 • 06/11/07 • Hunter Fan Company...

  • Page 15: Operating The Remote Control And Mounting The Holder

    10-6. You can mount the remote holder to any toggle switch plate with the screws already in the switch plate. Or, you can simply mount the remote holder on the wall. Steps 10-1 – 10-4 Step 10-5 Step 10-6 42753-01 • 06/11/07 • Hunter Fan Company...

  • Page 16: Operating And Cleaning Your Ceiling Fan

    To Change Airflow Direction Turn the fan off and let it come to a complete stop. Slide the reversing switch on the fan to the opposite position. Restart fan. Reversing Switch 42753-01 • 06/11/07 • Hunter Fan Company...

  • Page 17: Troubleshooting

    If you need parts or service assistance, please call 866-268-1936 or visit us at our Web site at http://www.hunterfan.com. Hunter Fan Company 2500 Frisco Avenue Memphis, Tennessee 38114 42753-01 • 06/11/07 • Hunter Fan Company...

Table of Contents