Rear Panel; Inputs - Extron electronics MTPX Plus 816 Setup Manual

Installation

Rear Panel

2 7 4
LOCAL INPUTS LOCAL OUTPUT
RGB
RGB
1
RGB RGB
LOCAL
ON
2
3
1 2 3
RJ - 45

INPUTS

INPUTS
AUDIO AUDIO INPUT SELECT
1 2 3
1 2 3 4
1 2 3 4
R R R R
L L L L
9 10 11 12
MONO AUDIO OUTPUTS
1
12 3 8
Figure 2-1 — MTPX Plus 1616 rear panel
N The MTPX Plus 816 and MTPX Plus 168 are housed in
the same 2U enclosure as the MTPX Plus 1616, but have
fewer TP input or output connectors to accommodate their
smaller matrix sizes.
4 5 2 7
LOCAL INPUTS LOCAL INPUTS
1 2
INPUT
SELECT
LISTED 1 2 3
US 1T23 LOCAL
®
I.T.E.
RJ-45 4 5 6
17 18
RS-232 OUTPUT INSERTION
LOCAL OUTPUTS
1 2 3 4 5 6 7 8
1 2
Tx Rx Tx Rx Tx Rx Tx Rx Tx Rx Tx Rx Tx Rx Tx Rx
1
9 10 11 12 13 14 15 16
2
Tx Rx Tx Rx Tx Rx Tx Rx Tx Rx Tx Rx Tx Rx Tx Rx 17 18
AUDIO INPUTS
L 1 R L 2 R L 3 R L 4 R L 5 R L 6 R L 1
12 3
Figure 2-2 — MTPX Plus 3232 rear panel
N The MTPX Plus 1632 and MTPX Plus 3216 are housed
in the same 3U enclosure as the MTPX 3232, but have
fewer TP input or output connectors to accommodate their
smaller matrix sizes.
LOCAL INPUTS
LOCAL INPUTS INPUTS INPUTS
100-240V 0.8A
L 1 R L 2 R
1 2 5 6 7 8
3 4
L 3 R L 4 R
50-60Hz 9 10 11 12
12 2 3 1
Figure 2-3 — MTPX Plus 128 rear panel
2-2 MTPX Plus Series • Installation
Refer also to the MTPX Plus User's Manual at www.extron.com.
1 5
CONTROL
RS - 232 OUTPUT INSERT
1 2 3 4 5 6 7 8
Tx Rx Tx Rx Tx Rx Tx Rx Tx Rx Tx Rx Tx Rx Tx Rx
OUTPUTS OUTPUTS
5 6 7 8 1 2 3 4 5 6 7 8
13 14 15 16 9 10 11 12 13 14 15 16
6 11 9
1
INPUTS INPUTS
3 4 5 6 7 8 9 10 11 12 13 14 15
19 20 21 22 23 24 25 26 27 28 29 30 31
OUTPUTS
3 4 5 6 7 8 9 10 11 12 13 14 15
19 20 21 22 23 24 25 26 27 28 29 30 31
CONTROL CONTROL
MONO AUDIO OUTPUTS
ETHERNET
R L 2 R L 3 R L 4 R L 5 R L 6 R L 7 R L 8 R
RESET
ACT LINK
8 11 9
LOCAL OUTPUTS LOCAL OUTPUTS OUTPUTS RS-232 OUTPUT INSERT RS-232 OUTPUT INSERT
1 R
L 1 2 3 4
1
1 2 3 4 LAN
Tx Rx Tx Rx Tx Rx Tx Rx REMOTE REMOTE
2
5 6 7 8
L 2 R RS-232 RS-232
5 6 7 8
ACT LINK
Tx Rx
7 8 6 5 10 11
Inputs
16
32
16
6
32
C Turn off power to the input and output devices, and
disconnect their power cords.
a
TP inputs — Connect up to 8, 16, or 32 (depending on
the matrix size) compatible TP inputs to the Inputs
RJ-45 connectors.
N Configure the switcher for the appropriate input (RS-232
or audio) for each TP input. See "Defining the Audio/
RS-232 Wire Pair (and Configuring the Remote Port)" on
page 3-6.
b
Local RGB (VGA) inputs — Connect analog
computer video sources to the Local Inputs
15-pin HD female connectors.
These connectors can also accept HD component video,
N
component video, S-video, or composite video.
c
Connect balanced or unbalanced
Local audio inputs —
stereo audio inputs to the Audio 5-pole captive screw
connectors.
Tip
Sleeve
Tip
Sleeve
Do not tin
the wires! Unbalanced Input
(high impedance)
Figure 2-4 — Audio input connector wiring
d
Input Select switches (switchers other than the
MTPX Plus 128) — Set the Input Select DIP switches
for each input that can be either local or on TP cable
from an MTP transmitter.
RJ-45 (down) for an input from an MTP transmitter (
Local (up) for a local (RGB video and audio) input (
N MTPX Plus 1616 and smaller have Input Select DIP
switches for inputs 1 through 3.
MTPX Plus 1632 and larger have Input Select DIP
switches for inputs 1 through 6.
MTPX Plus Series • Installation
Refer also to the MTPX Plus User's Manual at www.extron.com.
Tip
Ring
Sleeve (s)
Tip
Ring
Balanced Input
(high impedance)
LOCAL
ON
1 2 3
RJ - 45
INPUT SELECT
a )
b c )
and
2-3