BCM IXBDN-D510 User Manual

Intel atom d510/d410 nano-itx motherboard

Advertisement

IXBDN-D510/D410
Intel® Atom™ D510/D410 Nano-ITX Motherboard
User's Manual
Ver. 1.0
30GS090000409
June 2010

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IXBDN-D510 and is the answer not in the manual?

Questions and answers

Summary of Contents for BCM IXBDN-D510

  • Page 1 IXBDN-D510/D410 Intel® Atom™ D510/D410 Nano-ITX Motherboard User’s Manual Ver. 1.0 30GS090000409 June 2010...
  • Page 2: Table Of Contents

    IXBDN-D510/D410 Contents Before you Proceed ....................11 Motherboard Overview ..................12 1.2.1 Placement Direction ........................12 1.2.2 Screw Holes ..........................12 Motherboard Layout ..................... 13 1.3.1 Layout Content List ........................14 System Memory ..................... 15 1.4.1 DIMM Sockets Location ....................... 15 1.4.2...
  • Page 3 User’s Manual IXBDN-D510/D410...
  • Page 4: Safety Information

    IXBDN-D510/D410 Safety Information Electrical safety To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.
  • Page 5: Safety Declaration

    CAUTION: Information to prevent damage to the components when trying to complete a task. IMPORTANT: Instructions that you MUST follow to complete a task. NOTE: Tips and additional information to help you complete a task. IXBDN-D510/D410...
  • Page 6: Packing List

    IXBDN-D510/D410 Packing List Before you begin installing your single board, please make sure that the following materials have been shipped: 1 x IXBDN-D510/D410 MIni-ITX Motherboard 1 x CD-ROM contains the followings: • User’s Manual in PDF file • Drivers 1 x Cable Kit •...
  • Page 7: Revision History

    User’s Manual Revision History Revision Revision History Date V 1.0 First version for PCB 1.0 May, 2010 IXBDN-D510/D410...
  • Page 8: Specifications Summary

    IXBDN-D510/D410 Specifications Summary Specifications System Intel Atom Processor D510 Dual Core1.6GHz /D410 Single Core 1.6GHz 400/533 MHz AMI 16Mb SPI BIOS BIOS System Chipset ICH9R I/O Chipset Winbond W83627DHG-A Memory 2 x 240-pin UDIMM socket supports up to 4 GB DDR2 667/800 SDRAM...
  • Page 9: Block Diagram

    User’s Manual Block Diagram IXBDN-D510/D410...
  • Page 10 IXBDN-D510/D410 This chapter describes the main board features and the new technologies it supports. Product Product introduction introduction...
  • Page 11: Before You Proceed

    Before you install or remove any component, ensure that the ATX power supply is switched off or the power cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard, peripherals, and/or components. IXBDN-D510/D410...
  • Page 12: Motherboard Overview

    IXBDN-D510/D410 1.2 Motherboard Overview Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. Refer to the chassis documentation before installing the motherboard. Make sure to unplug the power cord before installing or removing the motherboard.
  • Page 13: Motherboard Layout

    User’s Manual 1.3 Motherboard Layout IXBDN-D510/D410...
  • Page 14: Layout Content List

    IXBDN-D510/D410 1.3.1 Layout Content List Slots Label Function Note Page XMM1 & 2 240-pin DDR2 DIMM slot MINIPCIE1 Mini PCI-e Slot PCIEX1_1 PCI Express x1 Slot Compact Flash Card (Rear side) Jumpers Label Function Note Page CLRTC1 Clear CMOS 3 x 1 header, pitch 2.54mm CLRTC2 Backlight 3.3V/5V Select...
  • Page 15: System Memory

    A DDR2 module has the same physical dimensions as a DDR DIMM but has a 240-pin footprint compared to the 184-pin DDR DIMM. DDR2 DIMMs are notched differently to prevent installation on a DDR DIMM socket. The following figure illustrates the location of the sockets: IXBDN-D510/D410...
  • Page 16: Memory Configurations

    IXBDN-D510/D410 1.4.2 Memory Configurations You can install 256MB, 512MB, 1GB and 2GB DDR2 SDRAM DIMMs into the DIMM sockets using the memory configurations in this section. Installing DDR2 DIMM other than the recommended configurations may cause memory sizing error or system boot failure.
  • Page 17: Removing A Ddr2 Dimm

    1. Press the two ejector tabs on the slot outward simultaneously, and then pull out the DIMM module. Support the DIMM lightly with your fingers when pressing the ejector tabs. The DIMM might get damaged when it flips out with extra force. IXBDN-D510/D410...
  • Page 18: Expansion Slots

    IXBDN-D510/D410 1.5 Expansion slots 1.5.1 MiniPCE Express Location In the future, you may need to install expansion cards. The following sub-sections describe the slots and the expansion cards that they support. Make sure to unplug the power cord before adding or removing expansion cards.
  • Page 19: Minipci Express Slot

    PCI Slots IX45GM has one PCI slots. The PCI slots support cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specifications. The figure shows a LAN card installed on a PCI slot. IXBDN-D510/D410...
  • Page 20: Jumpers

    IXBDN-D510/D410 1.6 Jumpers 1.6.1 Clear CMOS (CLRTC1) This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords.
  • Page 21: Com1, Com2 Ri/+5V/+12V Select (Jcompwr1, Jcompwr2)

    User’s Manual 1.6.2 COM1, COM2 RI/+5V/+12V Select (JCOMPWR1, JCOMPWR2) RI (Default) +12V 1.7 Connectors 1.7.1 Rear Panel Connectors IXBDN-D510/D410...
  • Page 22: Cpu Fan Connector (Fan1)

    IXBDN-D510/D410 Label Function Description VGA11 VGA Connector This 15-pin port is for a VGA monitor or other VGA-compatible devices. LAN_USB1, LAN (RJ-45) connector This port allows Gigabit connection to a LAN_USB2 Local Area Network (LAN) through a network hub. Refer to the table below for the LAN port LED indications.
  • Page 23: Lvds Connector (Jlvds)

    Do not forget to connect the fan cable to the fan connector. Insufficient air flow inside the system may damage the motherboard components. This is not a jumper! DO NOT place a jumper cap on the fan connector. 1.7.3 LVDS Connector (LVDS1) This motherboard supports 18-bit single channel LVDS panel. IXBDN-D510/D410...
  • Page 24: Lcd Inverter Connector (Jbkl)

    IXBDN-D510/D410 1.7.4 LCD Inverter Connector (BKL1) This function will support the control of internal LVDS brightness.
  • Page 25: System Panel Connector (F_Panel)

    LCD brightness through the VR signal. Vadj=0.75V ~ 4.25V (Recommended: 4.7K , > 1/16W) ENBKL LCD backlight ON/OFF control signal 1.7.5 System Panel Connector (F_PANEL1) This connector supports several chassis-mounted functions, and provides additional USB 5 & 6 ports. IXBDN-D510/D410...
  • Page 26 IXBDN-D510/D410 System Power LED (2-pin PWRLED) This 2-pin connector is for the system power LED. Connect the chassis power LED cable to this connector. The system power LED lights up when you turn on the system power, and blinks when the system is in sleep mode.
  • Page 27: Serial Port Connector (Com1 & Com2 )

    These 2 connectors are for serial (COM) port. Connect the serial port module cable to this connector, and then install the module to a slot opening at the back of the system chassis. COM 1&2 1.7.7 Digital I/O Connector (JDIO) This connector supports 8-bit General purpose I/O function. IXBDN-D510/D410...
  • Page 28: Sata Data Connector (Sata1&2)

    IXBDN-D510/D410 1.7.8 SATA Data Connector (SATA1, SATA2, SATA 3) These connectors are for the SATA signal cables to link SATA hard disk drives. SATA 1 SATA 2 SATA1 SATA3 SATA2 SATA5 SATA4 SATA 3 This connector is for the provided SATA power cable. This power supply cable is designed to fit this connector in only one orientation.
  • Page 29 This USB connector complies with USB 2.0 specification that supports up to 480 Mbps connection speed. Never connect a 1394 cable to the USB connectors. Doing so will damage the motherboard! The USB module is purchased separately. IXBDN-D510/D410...

This manual is also suitable for:

Ixbdn-d410

Table of Contents