Blue Seal E43 Installation And Operation Manual
  1. Manuals
  2. Brands
  3. Blue Seal Manuals
  4. Fryer
  5. Fast-Fri E43
  6. Installation and operation manual

Blue Seal E43 Installation And Operation Manual

Evolution series electric fryers
Hide thumbs Also See for E43:
Table of Contents

Advertisement

Quick Links

See also: Service Manual
I N S T A L L A T I O N A N D O P E R A T I O N M A N U A L
ELECTRIC FRYERS
E 4 3
E 4 3 E
E 4 4
E 4 4 E
For use in GB & IE
229099-10

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the E43 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Blue Seal E43

Summary of Contents for Blue Seal E43

  • Page 1 I N S T A L L A T I O N A N D O P E R A T I O N M A N U A L ELECTRIC FRYERS E 4 3 E 4 3 E E 4 4 E 4 4 E For use in GB &...
  • Page 2 Moffat Limited PO Box 10001 Christchurch New Zealand (03) 389 1007 Fax: (03) 389 1276 WORLD-WIDE BRANCHES UNITED KINGDOM Blue Seal 67 Gravelly Business Park Gravelly Park Birmingham West Midlands B24 8TQ (121) 327 5575 Fax: (121) 327 9711 UNITED STATES...

  • Page 3: Table Of Contents

    Assembly Electrical Connection Commissioning Operation....................11 Operation Guide ‘Over Temperature’ Control System Description of the Controls (E43 & E44) Description of the Controls (E43E & E44E) Operation of the Appliance Before Use Filling the Tank(s) Setting the Operating Temperature Frying Guide...
  • Page 4 Contents Controller Basic Programming Mode ............30 Programming the Password Protection. Programming the Timers. Programming the Temperature. Programming the Keypad Lock - Unlock. To Exit the Programming Mode. Controller Advanced Programming Mode ..........33 Timing Mode. Temperature Offset. Temperature Display Mode. Programming the Melt Cycle.

  • Page 5: Introduction

    Introduction We are confident that you will be delighted with your BLUE SEAL Electric Deep Fryer, and it will become a most valued appliance in your commercial kitchen. To ensure you receive the utmost benefit from your new Blue Seal Electric Deep Fryer, there are two important things you can do.

  • Page 6: Specifications

    The fat / oil drained off is thus returned directly to the fryer tank. Electrical Supply Requirements Power Supply Amps Total Power Model Input Voltage Type Frequency E43 / E43E 400-415Vac 3 P+N+E 50 / 60Hz 17kW 23.6 23.6 23.6 E44 / E44E 400-415Vac...

  • Page 7: Dimensions

    Dimensions E43 FRYER...
  • Page 8 Dimensions E44 FRYER...
  • Page 9 Dimensions E43E FRYER...
  • Page 10 Dimensions E44E FRYER...

  • Page 11: Installation

    Installation shall comply with local electrical and health and safety requirements. Blue Seal Deep Fryers are designed to provide years of satisfactory service, and correct installation is essential to achieve the best performance, efficiency and trouble-free operation. This appliance must be installed in accordance with National installation codes and in addition, in accordance with relevant National / Local codes covering electrical, fire safety and health and safety.

  • Page 12: Electrical Connection

    Installation Electrical Connection NOTE: ALL ELECTRICAL CONNECTIONS MUST ONLY BE CARRIED OUT BY A QUALIFIED PERSON. Each fryer should be connected to an adequately protected power supply and isolation switch mounted adjacent to, but not behind the fryer. This switch must be clearly marked and readily accessible in case of fire.

  • Page 13: Operation

    Only authorised service persons are to carry out installation, or servicing op- erations. Blue Seal Deep Fryers have been designed to provide simplicity of operation and 100% safety protection. A commercial heavy duty, electric fryer using high performance elements and is available in 4 model types;-...

  • Page 14: Description Of The Controls (E43 & E44)

    Operation Description of the Controls (E43 and E44 Fryers) E44 Manual Controls - Twin Tank Temperature Control Knob Temperature Graduations 60°C to 200°C. Power ‘ON’ Indicator. (When Neon Indicator main power switch is ‘ON’). (White) Heating ‘ON’ Indicator. (When Neon Indicator...

  • Page 15: Description Of The Controls (E43E & E44E)

    Operation Description of the Controls (E43E and E44E) Control Panel Functions Each control panel comprises the following:- One 4 digit, seven segment display with a 0.5” high, bright green LED display. Three green LED indicator lights located under each of the 3 Timer Controls. 6 Touch Control Keys;- ‘ON’...

  • Page 16: Operation Of The Appliance

    HOT. WHILST THE FRYER IS STILL E43 and E44 Models. Turn ‘ON’ the mains power at the mains supply, ensure that the Temperature Cut-Out Reset Switch has been reset (which is located behind the front access door, one for each tank on twin tank fryers E44 and E44E).
  • Page 17 Operation Idle Mode: After the appliance has exited the Melt Cycle Mode, or on Start-Up if the Melt Cycle Mode was by-passed, the appliance will go to the Idle Mode. If the temperature is more than 10° below its Set Temperature, the display will show ’HEAt’ and the heating element is ‘ON’.

  • Page 18: Before Use

    • The E43 single tank fryer will hold 27 to 29 litres of oil (22 - 23kg of shortening). • The E44 twin tank fryer will hold 14 litres of oil per pan (11kg of shortening per tank).

  • Page 19: Setting The Operating Temperature

    220°C, should there be a thermostat failure. Blue Seal E44 and E44E Fryers feature a split tank allowing distinctive products to be cooked in individual pans and at different temperatures. This allows products to be fried separately to prevent flavour contamination between products and allow products to be cooked at their optimum frying temperature.

  • Page 20: Care Of Frying Fats And Oils

    Operation With a little experience you can determine what amount of food may be added to the fryer without causing an excessive drop in temperature. If the temperature drop is excessive, either the food is too cold or there is too much food in the fryer.

  • Page 21: Frying Temperature Guide And Care Of Frying Medium

    Operation Frying Temperature Guide and Care of Frying Medium Table of Smoking Temperatures of Frying Mediums Based on work by the American Meat Institute. Medium Smoking Temperature Hydrogenated Fats. 190°C to 225°C. Compounds. 194°C to 223°C. Lards - Team-rendered. 165°C to 225°C. Refined deodorised lard.

  • Page 22: Cleaning And Maintenance

    Cleaning and Maintenance WARNING: DO NOT USE FLAMMIBLE SOLVENTS AND CLEANING AIDS ON OR IN CLOSE PROXIMITY TO THE FRYER HOT. WHILST THE FRYER IS STILL AUTIO N Always turn off the electrical supply before cleaning the appliance. This appliance is not water proof. Do not use water jet spray to clean interior or exterior of this appliance.

  • Page 23: Daily Cleaning

    Cleaning and Maintenance Locking Slide Locking Slide Fig 5 Fig 4 Daily Cleaning AUTIO N HOT OIL WILL BURN - DO NOT RUSH THIS JOB. At the end of each day or at the end of each shift, if the frying schedule is heavy, the frying medium should be drained and filtered into a receptacle.

  • Page 24: Weekly Cleaning

    Cleaning and Maintenance Weekly Cleaning NOTE: If the fryer usage is very high, we recommend that the weekly cleaning procedure is carried out on a more frequent basis. Proceed as for 'Daily Cleaning' to drain and filter the tank. Do not refill the tank with frying medium until it has been cleaned as shown below.

  • Page 25: Fault Finding

    Fault Finding Guide to Cooking Problems with Fryer This section provides an easy reference guide to the more common problems that may occur during the operation of your equipment. The fault finding guide in this section is intended to help you correct, or at least accurately diagnose problems with your equipment.
  • Page 26 Fault Finding Fault Possible Cause Remedy Rapid oil breakdown. Inadequate frying oil turnover. Adjust procedures to fry more food in the fryer to increase the turnover. Overheating of oil. Check the setting of the thermostat with a 'Mercury Glass' thermometer thermocouple.

  • Page 27: Fault Finding The Electrical System

    Fault Finding Fault Finding the Electrical System Fault Possible Cause Remedy Elements do not heat up. Check the mains power is supplied Turn on the power. Reset the to the unit and that a circuit circuit breaker or replace the breaker or fuse has not tripped / blown fuse.

  • Page 28: Wiring Schematics

    Wiring Schematics E43 Single Tank ELEMENTS THERMOSTAT THERMOSTAT PANEL HEAT SELECTOR POWER SWITCH MICROSWITCH OVERTEMP OVERTEMP PANEL GEAR TRAY EARTH...
  • Page 29 Wiring Schematics E44 Twin Tank ELEMENTS CONTROL PANEL THERMOSTAT HEAT HEAT SELECTOR SELECTOR POWER POWER SWITCH SWITCH MICROSWITCH OVERTEMP THERMOSTAT PANEL EARTH GEAR TRAY...
  • Page 30 Wiring Schematics E43E Single Tank ELEMENTS BROWN BROWN CONTROL PANEL BROWN BROWN MICROSWITCH OVERTEMP OVERTEMP PANEL GEAR TRAY...
  • Page 31 Wiring Schematics E44E Twin Tank...

  • Page 32: Controller Basic Programming Mode

    Controller Basic Programming Mode Controller Basic Programming Mode: NOTE: • 'Timer 1', 'Timer 2' and ‘Timer 3' keys on each control panel can be programmed with 3 different cook times for each tank. • The user may not enter Programming Mode whilst a timer is running. An alarm will sound indicating the key press, but the unit will not enter the Programming Mode.

  • Page 33: Programming The Timers

    Controller Basic Programming Mode Programming the Timers To change the settings, press either 'Timer 1 - Up’ key or 'Timer 3 - Down' key. Press the Programme Key ‘P’ to enter the ‘Programme Mode’. Once in the ‘Programme Mode’ the following ‘options can be cycled through by pressing the Programme Key again.

  • Page 34: Programming The Temperature

    Controller Basic Programming Mode Programming the 'Temperature'. Factory Default Settings The stored set ‘Temperature’ is displayed (default 350°F - 176.5°C 350°F - 176.5°C) with a flashing ‘F’ or ‘C’ for Fahrenheit or Celsius. To change the temperature, press either; i. 'Timer 1 - Up ’ to increase the time. ii.

  • Page 35: Controller Advanced Programming Mode

    Controller Advanced Programming Mode Controller Advanced Programming Mode: With mains power to the fryer turned ‘On’, press the ‘ON / OFF’ key to turn ‘On’ the appliance. Enter the ‘Advanced Programming Mode’, by pressing the Programme Key ‘P’ and 'Timer 1' key Press Together simultaneously.

  • Page 36: Temperature Display Mode

    Controller Advanced Programming Mode Temperature Display Mode Factory Default Settings The temperature display can be set for two temperature display modes:- 't -1’ - Display will show the oil temperature as an actual temperature. ’t - 0’ - The display will show the following temperature status; ‘HEAt’...

  • Page 37: Setting The Temperature Units

    Controller Advanced Programming Mode Setting the ‘Temperature Units’. The user may select from ‘F’ (Fahrenheit) or ‘C’ (Celsius). To change the 'Temperature Units', press either 'Timer 1 - Up’ key or 'Timer 3 - Down' key to change the selection. Press the Programme Key ‘P’, the change will be accepted and the display will revert to the ‘Idle Mode’.

  • Page 38: Replacement Parts List

    Replacement Parts List Replacement Parts List IMPORTANT: Only genuine authorized replacement parts should be used for the servicing and repair of this appliance. The instructions supplied with the parts should be followed when replacing components. For further information and servicing instructions, contact your nearest authorized service branch (contact details are as shown on the reverse of the front cover of this manual).

This manual is also suitable for:

E43eE44E44e

Table of Contents

Save PDF