Table of Contents
Advertisement
Quick Links
®
Hotwire
Shelf Concentration and Processing (SCP) Card
Installation Instructions
Document Number 8400-A2-GZ40-10
October 2003
Hotwire Shelf Concentration and Processing Card
A Hotwire
assembly that comprises a parent card with an ATM switch, a backplane interface,
a processor, a cell multiplexer/demultiplexer, and an uplink childcard. The
childcard determines the type of ATM uplink supported by the SCP card.
When the SCP card is used in a Hotwire 8620 or 8820 GranDSLAM chassis, it
aggregates DSL traffic from each of the DSL port cards in the chassis on the
chassis's backplane bus and concentrates it onto an ATM interface. The following
models are available:
The SCP card supports the following line cards:
„
„
„
With a Management Communications Controller (MCC) card installed in the same
chassis, the SCP card also supports Hotwire Time Division Multiplexer (TDM)
SDSL and SHDSL cards, Models 8775, 8777, 8779, and 8799.
8400-A2-GZ40-10
®
Shelf Concentration and Processing (SCP) card is a circuit card
SCP Card Model
8411-A1-000
8412-A1-000
8413-A1-000
8414-A1-000
8416-A1-000
8417-A1-000
8955 ReachDSL ATM Card
8965 ADSL ATM Card
8985 SHDSL ATM Card
October 2003
ATM Uplink Childcard
DS3
OC3/STM1 Multimode Fiber
OC3/STM1 Single Mode Fiber Intermediate Reach (15 km)
OC3/STM1 Single Mode Fiber Long Reach (40 km)
8-Port DS1 IMA (Inverse Multiplexing over ATM)
8-Port E1 IMA
1
Advertisement
Table of Contents
Related Manuals for Paradyne 8411-A1-000
Summary of Contents for Paradyne 8411-A1-000
-
Page 1: Installation Instructions
DSL traffic from each of the DSL port cards in the chassis on the chassis’s backplane bus and concentrates it onto an ATM interface. The following models are available: SCP Card Model ATM Uplink Childcard 8411-A1-000 8412-A1-000 OC3/STM1 Multimode Fiber 8413-A1-000 OC3/STM1 Single Mode Fiber Intermediate Reach (15 km) -
Page 2: Product Documentation Online
8900-A2-GB20 Hotwire ATM Line Cards, Models 8955, 8965, and 8985, User’s Guide To order a paper copy of a Paradyne document, or to speak with a sales representative, please call 727-530-2000. Refer to the appropriate Hotwire GranDSLAM installation guide to: „... -
Page 3: Installing The Scp Card
Installing the SCP Card SCP cards can be installed in: „ Slot A, Slot B, or both, of the 8820 GranDSLAM „ Slot A of the 8620 GranDSLAM Procedure To install the Hotwire SCP Card in a GranDSLAM chassis: 1. If there is a filler plate covering the slot, remove it. 2. - Page 4 Installing Two SCP Cards in the Same DSLAM Two SCP cards may be installed in one DSLAM to provide redundancy or load sharing. There are three basic configurations for paired SCP cards: „ Y-Cable – The OC3 ports of the two SCP cards are connected to the same uplink device.
- Page 5 DS3 Uplink SCP cards with a DS3 uplink have two BNC jacks: one for the transmit direction and one for the receive direction. To cable an SCP card with an DS3 uplink: 1. Connect the input cable to the RX jack on the faceplate of the SCP card. 2.
- Page 6 OC3 Uplink SCP cards with an OC3 uplink use an SFP transceiver that accepts an LC-type connector. To cable an SCP card with an OC3 uplink: 1. Remove the plastic dustcover from the SFP socket. 2. Insert the LC connector of your fiber optic cable into the SFP socket. 3.
-
Page 7: Ima Uplink
IMA Uplink SCP cards with an IMA uplink have an RJ45M-type 50-position connector with eight Tip/Ring and eight Tip1/Ring1 connections that conforms to ANSI T1.403-1999. The following splitter cables are available: „ Feature Number 8026-F1-001 for the Model 8416 SCP card terminates in eight 8-pin modular jacks. -
Page 8: Scp Card Leds
SCP Card LEDs The following table describes the meaning and states of the LEDs on the Hotwire SCP card faceplate. Example faceplates are shown at left. Type LED is . . . Indicating . . . SYSTEM Active Green, This SCP card is the active card Slow-cycling and is functioning normally. -
Page 9: Using The Default Management Address
Using the Default Management Address The SCP card uses Transaction Language 1 (TL1) language for Command Line Interface (CLI) commands and messages. The CLI can be used to configure and maintain the system, but the web interface is recommended. You can access the web interface using the default management address or a network address you specify using the CLI (see Setting the Management Address Using the... -
Page 10: Setting The Management Address Using The Cli
Setting the Management Address Using the CLI The management address can be set using the CLI. Procedure To set the management address of the SCP card using the CLI: 1. Using the supplied cable and DB9 adapter, connect a PC with a terminal emulation program to the SERIAL SCM jack of your GranDSLAM. -
Page 11: Using The Web Interface
Using the Web Interface To access the web interface: Procedure 1. Open your web browser. (Internet Explorer Version 6 or above is recommended.) 2. Type http:// and the IP address of the SCP card into the Address field of your browser window. -
Page 12: Bnc Jacks
BNC Jacks The following table shows the connections for BNC jacks (Model 8411). Table 1. BNC Jack Connections Connector Label Connection Description Transmit Transmit signal Shell Transmit signal return Receive Receive signal Shell Receive signal return IMA Interface Pin Assignments Table 2 lists connector pin assignments for Model 8416, and the Model 8417 when used with modular connectors for a 120-ohm E1 connection. - Page 13 Table 2. Feature Number 8026-F1-001 Pin Assignments (2 of 2) 8026-F1-001 DS1 or 120 Ohm 50-Position Telco RJ48C Connector E1 Port Connector Pinouts Pinouts Function Port 5 Data Out (Tip) Data Out (Ring) Data In (Tip) Data In (Ring) Port 6 Data Out (Tip) Data Out (Ring) Data In (Tip)
- Page 14 Table 3. Feature Number 8027-F1-001 Pin Assignments (2 of 2) 50-Position Telco 75 Ohm E1 Port Function Connector Pinouts BNC Connector Port 3 Data In Shell (Ring) Pin (Tip) Data Out Shell (Ring) Pin (Tip) Port 4 Data In Shell (Ring) Pin (Tip) Data Out Shell (Ring)
-
Page 15: Equipment List
The following feature numbers may be used to order SCP cards, line cards, and related cables. Table 4. Feature Numbers Description Feature Number Cards SCP Card: DS3 8411-A1-000 SCP Card: OC3/STM1 Multimode Fiber 8412-A1-000 SCP Card: OC3/STM1 Single Mode Fiber Intermediate Reach 8413-A1-000 SCP Card: OC3/STM1 Single Mode Fiber Long Reach 8414-A1-000... -
Page 16: Scp Card Technical Specifications
SCP Card Technical Specifications Table 5. SCP Card Technical Specifications (1 of 2) Specifications Criteria Size Length: 10.4 inches (26.42 cm) Height: 11.15 inches (28.32 cm) Width: 1.0 inches (2.54 cm) Weight Approximately 1.7 lbs. (0.76 kg) Approvals Safety Certifications Refer to the equipment’s label for approvals on product. -
Page 17: Important Safety Instructions
Class 1 laser product (Appareil à Laser de Classe 1). If the Class 1 laser device is not purchased from Paradyne Corp., the customer is responsible to insure that the Class 1 AEL (Allowable Emissions Limit) per EN/IEC 60825 is not exceeded after the laser transceivers have been installed. -
Page 18: Warranty, Sales, Service, And Training Information
Document Feedback We welcome your comments and suggestions about this document. Please mail them to Technical Publications, Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773, or send e-mail to userdoc@paradyne.com. Include the number and title of this document in your correspondence. Please include your name and phone number if you are willing to provide additional clarification.