Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for X10 PUR08
Summary of Contents for X10 PUR08
- Page 1 PUR08 EARNING EMOTE ’ WNER ANUAL...
- Page 2 IRST FCC C AUTION AFETY ONSIDERATIONS THIS DEVICE COMPLIES WITH PART 15 OF Remember to exercise good common Remember to exercise good common THE FCC RULES. sense when using your X-10 PRO sense when using your X-10 PRO OPERATION IS SUBJECT TO THE home automation remote - home automation remote - FOLLOWING TWO CONDITIONS:...
-
Page 3: Table Of Contents
ONTENTS NTRODUCTION Congratulations on your purchase of the ..........5 NTRODUCTION X-10 PRO Learning Remote......... 6 ETTING TARTED Make your lights and appliances go Make your lights and appliances go ....6 ONTROLLERS AND ODULES to work for you..to work for you.. -
Page 4: Getting Started
ETTING TARTED Because we know that you are eager to OUSE ODES AND ODES get started, we’ve kept this introduction as short as possible, but it contains very valuable information, so you should read through it very carefully. UNIT CODE DIAL ONTROLLERS AND ODULES... -
Page 5: Installing The Components
NSTALLING THE 1. Set the House OMPONENTS Code to ‘A’ and the Unit Code to ‘2.’ RANSCEIVER ODULE The Transceiver Module receives radio frequency (RF) commands from remotes to operate a lamp or appliance plugged into 2. Plug a lamp into it. -
Page 6: Remote
ETTING CHANNEL EMOTE Works like your original remote. Also used to turn X-10 Pro modules on and off. UTTON ESCRIPTIONS MUTE INDICATOR LIGHT Works the same as your original remote. The indicator light flashes when the Also turns All Modules Off, when in X-10 remote is operating. -
Page 7: Clearing The Memory
CLEARING THE MEMORY You can also clear the memory for just a particular mode (TV, VCR, etc.). It is recommended that you clear the memory in the Learning Remote before you 1. Press and hold start programming it: SETUP until the LED indicator lights steadily. -
Page 8: Setting Up For Tv, Vcr
TV, VCR, If the LED blinks rapidly when you If the LED blinks rapidly when you ETTING UP FOR enter the code, you may have entered an enter the code , CD, ABLE ATELLITE invalid code. Recheck the code in the code ECEIVER list and try again. - Page 9 GE ........013,016,017,022,035,065,067,068 ............................100,176,177,178,179,180,181,194 PANASONIC ..........016,067,075,183 GIBRALTER ..............017,164 PHILCO ......... 016,017,018,021,022,025 GOLDSTAR .......... 017,018,022,025,069 ........075,081,082,087,088,090,196,197 ............070,071,168,169,184,185 PHILIPS ......016,017,019,021,022,025,075,081 GRUNDY ............051,059,184 ........082,087,088,089,099,100,101,102 ....................PILOT ................017,184 HALLMARK ..............017,022 PIONEER ....... 017,022,103,104,105,192,198 HARVARD ................
-
Page 10: Vcr Codes
VIDTECH .............. 017,018,022 HI-Q ..................036 VIKING ................. 187 ........................................INSTANT REPLAY ............. 034 WARDS ......... 013,014,017,018,022,037,046 ..............................059,065,075,081,082,087,088 JCL ..................034 ........089,096,100,101,108,132,133,197 JC PENNEY ......022,023,024,026,027,034,035 ..............................068,069,071,072,073,120,131 YAMAHA ............017,018,022 JENSEN ................124 YUPITERU ................055 JVC ......... -
Page 11: Cable Codes
SANKY ................014,117 MEMOREX ................039 SANSUI ............023,105,124,136 MOVIE TIME ............015,040,041 SANYO ..............024,026,036 ....................SCOTT ............025,028,038,045 NSC ................015,040 ..............051,078,106,129 ....................SEARS ........... 024,027,034,036,061 OAK ..............015,029,042 .............. 062,063,064,068,069 ......................................120,131 PANASONIC ............013,061,064 SHARP ........ - Page 12 GENERAL INSTRUMENTS ....017,018,019,046,047,048 ........................................DENON ..............023,024 JANEIL ................049 ....................EMERSON ............014,025,026 JEROLD ................050 ........................................KENWOOD ............... 051 FISHER ......... 020,027,028,029,030,071 ........................................LUXOR ................052 GE ..................078 ....................GENEXXA ............ 025,026,031,072 MACOM STATE ..............053 GOLDSTAR ..............
-
Page 13: Using Aux To Control
....................4. Press and release TEAC ..........029,042,052,062,063,064 the mode button TECHNICS ............069,086,089 THETA DIGITAL ............... 084 that matches the TOSHIBA ................074 A/V equipment you ....................want to control. VECTOR RESEARCH ..........017,032 The LED blinks VICTOR ................035 .................... -
Page 14: Searching For Codes
EARCHING ODES DENTIFYING ODES FOUND USING THE EARCH ROCEDURE 1. Press and hold 1. Turn on the device SETUP until the you want to LED indicator control. lights steadily. Release Setup button. 2. Press the mode 2. Press and hold button that SETUP until the matches the... -
Page 15: Setting The Sleep Timer
EARNING ETTING THE LEEP IMER Your PUR08 Learning Remote has the codes for most TVs, VCRs, etc. in its code The Sleep Timer automatically turns off the library. However, if the code for your TV after the time you set. Press the TV... - Page 16 Press VCR on the PUR08 and the appro- remote you are learning from. priate key on the PUR08 to access the first Use buttons L1 and L2 to learn codes for VCR.
-
Page 17: Controlling X-10 Pro Modules
X-10 P ONTROLLING 2. Press and hold ODULES TIMER until the LED indicator lights steadily. If you have already installed a PAT01 Release TIMER Transceiver Module, (sold separately) you button. can control it and other X-10 Pro modules as follows: 3. -
Page 18: Controlling An Ir Mini Controller
2. Press and hold 3. Enter 014 to SETUP until the control an IR Mini LED indicator Controller, 013 for lights steadily. standard Release the Setup X-10 PRO control. button. The LED turns off after the last digit entered. 3. Use the number buttons to enter Note: In most cases, you will not need to Note:... -
Page 19: Troubleshooting
ROUBLESHOOTING ARRANTY 24 MONTH LIMITED WARRANTY The Transceiver Module doesn’t The Transceiver Module doesn’t X-10 PRO (X-10) WARRANTS ITS PRODUCTS TO BE FREE FROM DEFECTIVE MATERIAL AND respond to the remote: respond to the remote: WORKMANSHIP FOR A PERIOD OF TWO (2) YEARS FROM THE ORIGINAL DATE OF •...