Related Manuals for FieldServer FS-8700-60 Gardner Denver
Summary of Contents for FieldServer FS-8700-60 Gardner Denver
- Page 1 A Sierra Monitor Company Driver Manual (Supplement to the FieldServer Instruction Manual) FS-8700-60 Gardner Denver Auto Sentry ES/RS2000 APPLICABILITY & EFFECTIVITY Effective for all systems manufactured after May 1, 2001...
-
Page 2: Table Of Contents
Party Configuration ..............2 2.1.4. Optional Items ....................2 Hardware Connections ..................3 1.03 Hardware Connection Tips / Hints..............3 Configuring the FieldServer as a Gardner Denver Auto Sentry ES/RS2000 Client ..........................4 1.04 Data Arrays/Descriptors ................... 4 1.05 Client Side Connection Descriptions ..............5 1.06... -
Page 3: Gardner Denver Auto Sentry Es/Rs2000 Description
Page 1 of 11 Gardner Denver Auto Sentry ES/RS2000 Description The Gardner Denver Auto Sentry ES/RS2000 driver allows the FieldServer to transfer data from devices over either RS-232 or RS-485 using Gardner Denver Auto Sentry ES/RS2000 protocol. The driver can be configured to communicate with ES Controllers with software versions V2.0X, V2.1X and RS2000 Controllers with software versions... -
Page 4: Driver Scope Of Supply
RS-232 or RS-485 communications to an external monitoring system. Please refer to manufacturer’s setup instructions. 2.1.4. Optional Items PART # Vendor/Manufacturer Description 485LDRC B&B Electronics RS-232/RS-485 converter FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: support@fieldserver.com... -
Page 5: Hardware Connections
FS-8700-60 Gardner Denver Manual Page 3 of 11 Hardware Connections The FieldServer is connected to the ES/RS2000 Controller as shown in the connection drawing below: Configure the ES/RS2000 Controller according to manufacturer’s instructions. 1.03 Hardware Connection Tips / Hints If inter-controller communications are set up for the controller, connect to the RS-232 port only. -
Page 6: Configuring The Fieldserver As A Gardner Denver Auto Sentry Es/Rs2000 Client
Gardner Denver Auto Sentry ES/RS2000 Controller. 1.04 Data Arrays/Descriptors The configuration file tells the FieldServer about its interfaces, and the routing of data required. In order to enable the FieldServer for Gardner Denver Auto Sentry ES/RS2000 communications, the driver independent FieldServer buffers need to be declared in the “Data Arrays”... -
Page 7: Client Side Connection Descriptions
Not all ports shown are necessarily supported by the hardware. Consult the appropriate Instruction manual for details of the ports available on specific hardware. FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: support@fieldserver.com... -
Page 8: Client Side Node Descriptors
Starting location in Data 0 to maximum specified in Data_Array_Offset Array “Data Array” section above Function of Client Map Function RDBC, Passive_Client Descriptor FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: support@fieldserver.com... -
Page 9: Driver Related Map Descriptor Parameters
Values Rate at which data is polled. Note that the Scan_Interval Poll_Delay Connection parameter affects the ≥0.1s effective scan interval. FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: support@fieldserver.com... -
Page 10: Map Descriptor Example 1 - Polling All Available Controller Data
16 for temperature in degrees F ES V2.0X Controllers do not respond with this field ES V2.0X Controllers do not respond with this field FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: support@fieldserver.com... -
Page 11: Map Descriptor Example 2 - Polling Only Specific Data Items
Gar_cmd as the Gar_cmd and Node_Name fields match. Operating data. active map descriptor. RS2000 V4.0X Controllers set this field to zero FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: support@fieldserver.com... -
Page 12: Appendix 1. Advanced Topics
RDBC active map descriptor, the driver still gets all data of Gar_cmd type from the controller in a single poll, but only stores the data item in question. FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: support@fieldserver.com... -
Page 13: Appendix 2. Revision History
Redrew connection diagram. 7/16/04 1.03a Reformatted document. Replaced connection diagram with 8/24/04 1.03a original created by Deon. 12/29/04 JD 1.03a Releasing FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: support@fieldserver.com...
Need help?
Do you have a question about the FS-8700-60 Gardner Denver and is the answer not in the manual?
Questions and answers