Treadmill Operation - Horizon Fitness CLUB SERIES CST3.5-4.5 User Manual

TENSIONING THE RUNNING BELT
NOTE: Running belt should NOT be moving during
adjustments
If you can feel a slipping sensation when running on
the treadmill, the running belt must be tightened.
In most cases, the belt has stretched from use,
causing the belt to slip. This is a normal and common
adjustment. To eliminate this slipping, turn the
treadmill off and tension BOTH THE REAR ROLLER
BOLTS using the supplied Allen wrench, turning them
1/4 TURN to the right as shown. Turn the treadmill
on and check for slipping. Repeat if necessary, but
NEVER TURN the roller bolts more than 1/4 turn at
a time. Belt is properly tensioned when the slipping
sensation is gone.
Belt is too far to the right side
Belt is too far to the left side
14
CST3.5-4.5 Treadmill Rev0.2.indd 14-15
CENTERING THE RUNNING BELT
The running belt has been properly adjusted at the
factory before it was shipped. At times the belt can
move off-center during shipment. Before operating the
treadmill, make sure the belt is centered and remains
centered to maintain smooth operation.
CAUTION: Do not run belt faster than 1/2 mph while
making adjustments. Keep fingers, hair and clothing
away from belt at all times.
If the running belt is too far to the right side:
With the treadmill running at 1/2 mph, turn the right
adjustment bolt clockwise 1/4 TURN at a time (using
the supplied Allen wrench). Check the belt alignment.
Allow belt to run a full cycle to gauge if more adjustment
is needed. Repeat if necessary, until the belt remains
centered during use.
If the running belt is too far to the left side:
With the treadmill running at 1/2 mph, turn the right
adjustment bolt counter-clockwise 1/4 TURN at a time
(using the supplied Allen wrench). Check the belt
alignment. Allow belt to run a full cycle to gauge if more
adjustment is needed. Repeat if necessary, until the belt
remains centered during use.
TREAD MIL L O PERATIO N
� � � � �
� � � � � � � � � � � � � � � � ���
�
���
�
��� �
��
�
� � � � ��
�
�� �
��
�
�� �������������
�
��
� � � � � � � � �
� ���
�� � �
��
�
��
�
� � � � � � � � � �
�����������
��������������
� �
� �
�
Note: There is a thin protective sheet of clear plastic on the overlay of the console and should be removed.
A) MONITOR DISPLAY: Speed, Time, Pulse, Distance, Incline, Calories and Program Profiles.
B) ADDITIONAL DISPLAY WINDOWS: Time and Speed (CST4.5 only)
C) STOP: Press to pause/end your workout. Hold for 3 seconds to reset the treadmill.
D) START: Simply press to begin exercising or starts your program.
E) ENTER: Used to select Program, Level and Time. Press to change display feedback during workout, Hold to scan.
F) ONE-TOUCH INCLINE KEYS: Used to reach desired incline more quickly.
G) ONE-TOUCH SPEED KEYS: Used to reach desired speed more quickly.
H) 1/2 KEYS: One-touch keys for increasing speed (0.5 mph increments) and incline (0.5% increments).
I) BACK-LIT INCLINE INDICATORS: Illuminate to indicate current incline.
J) BACK-LIT SPEED INDICATORS: Illuminate to indicate current speed.
K) SAFETY KEY POSITION: Enables treadmill when safety key is inserted.
L) WATER BOTTLE / CD / MP3 HOLDERS: Holds personal workout equipment.
M) READING RACK: Holds reading material. (Remove sales sticker before use)
� �
�
��� � � � � � � � � � � � � � �
���
���
���
���
���
��
���
�� � � � � �
���
�������
��
���
��
� � � � � � ���
� � � � � �
� � � � ��
� � �� � ���
��
���
� ����
��
� �� ���
��
���
��
���
� � � �
�������������
�
� �
15
4/21/05 11:22:50 AM