Alliance Laundry Systems HCD020GD2 Manual
  1. Manuals
  2. Brands
  3. Alliance Laundry Systems Manuals
  4. Washer
  5. HCD020GD2
  6. Manual
Alliance Laundry Systems HCD020GD2 Manual

Alliance Laundry Systems HCD020GD2 Manual

Hide thumbs Also See for HCD020GD2:
Table of Contents

Advertisement

Quick Links

Washer-Extractor
Refer to Page 7 for Model Numbers
CHM495R_SVG
Original Instructions
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. F8208501ENR10
www.alliancelaundry.com
March 2017

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HCD020GD2 and is the answer not in the manual?

Questions and answers

Related Manuals for Alliance Laundry Systems HCD020GD2

Summary of Contents for Alliance Laundry Systems HCD020GD2

  • Page 1 Washer-Extractor Refer to Page 7 for Model Numbers CHM495R_SVG Original Instructions Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) Part No. F8208501ENR10 www.alliancelaundry.com March 2017...
  • Page 3 Any problems or conditions not understood should be reported to the dealer, distributor, service agent or the manufacturer. © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...

  • Page 4: Table Of Contents

    Power Save Mode..................14 © Copyright 2017, Alliance Laundry Systems LLC All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher.
  • Page 5 Rapid Advance rAPd..................30 Exit Manual Mode End..................30 Production Test Cycle................32 To Enter Production Test Cycle..............32 To Exit Production Test Cycle................ 33 Error Codes..................36 © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...
  • Page 6 Power Fail Recovery................38 Default Cycles..................39 © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...

  • Page 7: Model Identification

    HCN040GE2 HCU040GX2 SCN040GC2 SCU040GNF UCU040GNF HCN040GN2 HCU040GY2 SCN040GD2 SCU040GNV UCU040GNV HCN040GNF ICN040GNF SCN040GE2 SCU040GX2 VCU040GN2 HCN040GNV SCB040GNF SCN040GN2 SCU040GY2 HCN040GX2 SCD040GD2 SCN040GNF UCH040GNF Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...
  • Page 8 SCU080GNF HCN080GNF HCU080GXF SCN080GNF SCU080GXF HCN080GXF HCU080GYF SCN080GXF SCU080GYF HCN080GYF ICN080GNF SCN080GYF UCH080GNF 100 Pound HCH100GNF ICN100GNF SCN100GNF UCL100GNF UCN100GNF HCL100GNF SCH100GNF UCH100GNF HCN100GNF SCL100GNF © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...

  • Page 9: Introduction

    For technical assistance, contact your local distributor or contact: Alliance Laundry Systems Shepard Street P.O. Box 990 Ripon, WI 54971-0990 U.S.A. www.alliancelaundry.com Phone: +1 (920) 748-3121 Ripon, Wisconsin © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...

  • Page 10: Preliminary Information

    Start Mode and require pressing the START switch. If the power failure is greater than five (5) seconds and OPL Mode is enabled, the cycle can not be resumed. © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...

  • Page 11: Control Identification

    5. LED Status Lights 6. Spin 7. Door 8. Wash 9. Bleach 10. Rinse 11. Hot 12. Warm 13. Cold 14. Delicate Cold 15. Start Figure 1 © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...

  • Page 12: Display Identification

    During diagnostic testing or manual programming of the control, these digits will display descriptive codes and values (as described in Entering the Manual Mode). © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...

  • Page 13: Machine Operation

    (0), the display will show FrEE. After pressing the START switch, the door will lock and the cy- cle will begin. © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...

  • Page 14: Special Features

    This feature allows the user to start a cycle without satisfying the vend price. For details on enabling OPL Mode, refer to Programming the DIP Switch . © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...

  • Page 15: Opening The Top Cover

    The top cover is located on the top of the machine. CHM1357R_SVG 1. Top Cover Lock 2. Top Cover 3. Top Cover Hinge 4. Peg Figure 2 © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...

  • Page 16: Programming The Dip Switch

    Default OPL Mode OPL Mode Off OPL Mode On Heater Heater Off Heater On Drain Option Gravity Drain Pump Drain Gravity Drain Unused Table 2 © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...

  • Page 17: Entering The Manual Mode

    2. Right Programming Button (as you are facing the machine) 3. Left Programming Button (as you are facing the machine) 4. DIP Switch Figure 3 © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...

  • Page 18: Programming Control

    Ready Mode. NOTE: The codes in the Option Display column of are what will show in the display when that option is se- lected. © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...

  • Page 19: Programmable Options Available

    Cycle Enable Slow Drain Detection Adjust- 0-255 SdAd ment Number of Balance Retries bALr (Design 2 and 3 models) Leak Detection Test Table 3  continues... © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...
  • Page 20 DC Bus Display Test (Design dCbt 2 and 3 models) DIP Switch Test DIPt Rapid Advance rAPd Exit Manual Mode *Read only - cannot be cleared. Table 3 © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...

  • Page 21: Programming Flowcharts

    Programming Control Programming Flowcharts © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...
  • Page 22 Total # of Rapid Advance Cycles “PLEU” Prewash Fill Level “ALEU” Wash Fill Level “rLEU” Rinse #1, #2 and #3 Fill Level Continued CHM1387R_SVG Figure 4 © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...
  • Page 23 Cycle Pause Enable (Gravity Drain Models Only) “LdEn” Leak Detection During Cycle Enable “SdEn” Slow Drain Detection During Cycle Enable “SdAd” Slow Drain Detection Adjustment Continued CHM1386R_SVG Figure 5 © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...
  • Page 24 Balance Weight Test (Design 2 and 3 Models) (F-Speed Design 1 Models) “dIPt” DIP Switch Test “rAPd” Rapid Advance “End” Exit Manual Mode CHM1559R_SVG Figure 6 © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...

  • Page 25: Vend Price Ats

    Programming buttons at the same time. The current Coin Au- set for 0100, the vend price displayed will decrease by 1.00 for dio Beep status will appear in the display. each dollar coin entered. © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...

  • Page 26: Card Display Option Card

    4. Press the Right or Left Programming button to change the This option allows the owner to access Rapid Advance Cycle current status. counter audit information. © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...

  • Page 27: Rinse #1, #2 And #3 Fill Level Rleu

    1. Control must be in Manual Mode. Refer to Entering the Man- NOTE: The default value is on. ual Mode. 4. Press the Right or Left Programming button to change the current status. © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...

  • Page 28: Rinse #2 Enable R2En

    This option allows the owner to program the warm cycle temper- tate step in the cycle, the control monitors the water level for 60 ature for models equipped with temperature sensing capabilities. © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...

  • Page 29: Slow Drain Detection During Cycle Enable Sden

    2. Press the Right or Left Programming button to scroll through control will alternate the display between FAIL and FILL. The the programmable options until SdAd appears in the display. © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...

  • Page 30: Balance Weight Test Balt (F-Speed Design 1 Models Only)

    2. Press the Right or Left Programming button to scroll through This option allows the owner to exit the Manual Mode. the programmable options until dCbt appears in the display. © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...
  • Page 31 2. When End appears in the display, press the Right and Left Programming buttons at the same time. The control will re- vert back to the previous control mode. © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...

  • Page 32: Production Test Cycle

    Production Test Cycle. 5. Remove jumper harness from control and reconnect to Frame Balance Switch Harness. Refer to Figure 7 . CHM528R_SVG 1. Jumper Harness Figure 7 © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...

  • Page 33: To Exit Production Test Cycle

    CoIn or oPL Control Type Coin or OPL Drain Type Drain or pump drAn or PUnP Table 5  continues... © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...
  • Page 34 Warm Fill to Standard Low Level All water outputs turned off when standard bFIL water level is reached. Table 5  continues... © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...
  • Page 35 SP 2 Medium Speed Extract Step skipped on F-speed models. SP 3 Power Down Turn Power off. Remove factory test har- Prdn ness. Table 5 © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...

  • Page 36: Error Codes

    If control senses a drop in water level during machine cycle, control shows error after completed cycle, for one minute, when door is opened. Table 6  continues... © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...
  • Page 37 The drive received an invalid motor movement command. Cycle Ed11** will continue, no user input required. *Design 1 models only. **Design 2 and 3 models only. Table 6 © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...
  • Page 38 The control will display PAUS until the coast down timer is zero. © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...
  • Page 39 Heat (if enabled) Drain Time for Drain Design 1 (2 speed) (min.) Design 1 (F- speed) 1:44 1:44 1:44 1:44 Design 2 and 3 Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...
  • Page 40 1:44 1:44 1:44 1:44 Design 2 and 3 1:10 1:10 1:10 1:10 Spin (2 speed/F-speed) Spin/Medium Spin/Medium Spin/Medium Spin/Low Time for Spin (min.) Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...
  • Page 41 F-speed (Design 1) 00:30:31 00:30:31 00:30:31 00:30:00 F-speed (Design 2 00:25:42 00:25:42 00:25:42 00:25:32 and 3) * Total cycle time includes final spin coast down time. © Copyright, Alliance Laundry Systems LLC - Part No. F8208501ENR10 DO NOT COPY or TRANSMIT...

This manual is also suitable for:

Hch020gnfHcl020gc2Hcl020gd2Hcl020gn2Hcl020gnfHcn020gc2 ... Show all

Table of Contents