Page 1
CCD-TR618/TR618E/TR718E/TR728E/TR818 CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/ TRV78/TRV78E/TRV88/TRV98/TRV98E RMT-708 US Model SERVICE MANUAL CCD-TR818/TRV58/TRV68/TRV88/TRV98 Canadian Model CCD-TR818/TRV58/TRV68/TRV98 AEP Model UK Model CCD-TR718E/TR728E/TRV58E/ TRV59E/TRV78E/TRV98E E Model Ver 1.4 2002. 05 CCD-TR618/TR618E/TR818/TRV49/ TRV49E/TRV58/TRV68/TRV78/ TRV78E/TRV88/TRV98/TRV98E Australian Model CCD-TR618E/TRV49E/TRV78E/TRV98E Hong Kong Model CCD-TR618E/TRV49/TRV49E/TRV78/ TRV78E/TRV98/TRV98E Tourist Model CCD-TRV49/TRV49E/TRV78/ TRV78E/TRV98/TRV98E Chinese Model...
Page 2
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
Page 3
• SUPPLIED ACCESSORIES Check that the following accessories are supplied with your camcorder. • Abbreviation HK : Hong Kong model : Tourist model : Brazilian model — 3 —...
TABLE OF CONTENTS SERVICE NOTE 2-5. CABINET (R) SECTION (CF-077 BOARD) (TR MODEL) ·································································· 2-6 POWER SUPPLY DURING REPAIRS ····························· 8 2-6. CABINET (R) SECTION [CONTROL SWITCH TO TAKE OUT A CASSETTE WHEN NOT EJECT BLOCK (CF-1000)] (TRV MODEL) ······························ 2-7 (FORCE EJECT) ································································...
Page 7
7-2. REC C Current Check (VC-251 board) ························ 5-45 7-3. REC AFM Current Adjustment (VC-251 board) ·········· 5-46 7-4. Processing after completed adjustment ························· 5-46 3-5. IR TRANSMITTER ADJUSTMENTS (CCD-TRV98) ··· 5-47 IR Video Carrier Frequency Adjustment (MI-041 board) · 5-47 IR Video Deviation Adjustment (MI-041 board) ···········...
SERVICE NOTE POWER SUPPLY DURING REPAIRS In this unit, about 10 seconds after power is supplied (8.4V) to the battery terminal using the service power cord (J-6082-223-A), the power is shut off so that the unit cannot operate. This following method is available to prevent this. Method: Use the DC IN terminal.
SELF-DIAGNOSIS FUNCTION Self-diagnosis Function Self-diagnosis Display When problems occur while the unit is operating, the counter of the When problems occur while the unit is operating, the self-diagnosis function starts working, and displays on the viewfinder or LCD or viewfinder or LCD or Display window shows a 4-digit display Display window what to do.
Self-diagnosis Code Table Self-diagnosis Code Block Detailed Symptom/State Correction Function Code Non-standard battery is used. Use the InfoLITHIUM battery. Condensation. Remove the cassette, and insert it again after one hour. Video head is dirty. Clean with the optional cleaning cassette. LOAD direction.
Page 11
Self-diagnosis Code Block Detailed Symptom/State Correction Function Code Inspect the lens block focus reset sensor (Pin qs of CN301 of VC- Difficult to adjust focus 251 board) when focusing is performed when the control dial is (Cannot initialize focus.) rotated in the focus manual mode and the focus motor drive circuit (IC301 of VC-251 board) when the focusing is not performed.
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E SECTION 1 This section is extracted from instruction manual. (CCD-TRV49E/TRV58E/TRV59E/ GENERAL TRV78E/TRV98E model)
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E SECTION 2 DISASSEMBLY The following flow chart shows the disassembly procedure. 2-1. Video light (Video light model) PD-131 board service position 2-2. LCD section (PD-131 board) (TRV model) MI-040/041 board service position 2-3. Front panel section, MI-040/041 board Mechanism deck service position 2-4.
[CONNECTION OF EQUIPMENTS] (TR MODEL) CPC connector Info lithium battery Two claws (L series) CPC lid Adjustment remote commander (RM-95) AC power AC IN adaptor CPC-jig for BX/BK (J-6082-521-A) (TRV MODEL) CN713 Info lithium battery (L series) Adjustment remote commander (RM-95) Two claws AC power AC IN...
2-3. FRONT PANEL SECTION, MI-040/041 BOARD 1 Open the jack cover 3 MI screw 4) (H) 2 Two MI screws 4) (H) 4 Two MI screws 4) (H) 5 Claw 6 FP-263 flexible board (24P) 7 Front panel section 1 Two tapping screws (B2 2 Two tapping screws (B2...
2-4. CABINET (L) SECTION 3 Cassette lid assembly 2 Two MI screws 4 MI screw 4) (H) 4) (H) 6 Two MI screws 4) (H) 8 Cabinet (L) section 5 MI screw 4) (H) 7 MI screw 4) (H) [MECHANISM DECK SERVICE POSITION] Note: Use the parts only which can be removed easily from outside of the mechanism deck.
[SERVICE POSITION TO CHECK THE VTR SECTION] Connection to Check the VTR Section To check the VTR section, set the VTR to the "Forced VTR power ON" mode. Operate the VTR functions using the adjustment remote commander (with the HOLD switch set in the OFF position). Setting the “Forced VTR Power ON”...
Page 48
[SERVICE POSITION TO CHECK THE CAMERA SECTION] Connection to Check the Camera Section To check the camera section, set the camera to the "Forced camera power ON" mode. Setting the “Forced Camera Power ON” mode Exiting the “Forced Camera Power ON” mode 1) Select page: 0, address: 01, and set data: 01.
2-12.MECHANISM DECK 4 Control switch block (FK-1000) 2 MD frame A 1 Screw lock ace, p2 1 Three screws lock ace, p2 2 Two claws 1 Claw 2 Slide it in the direction of the arrow A and disengage the claws B Remove the LS lid assembly in the direction of the arrow C .
BACK LIGHT BACK LIGHT REMOTE COMMANDER MODEL : CCD-TR728E/TRV49/TRV49E/TRV59E/TRV78/TRV78E/TRV98/TRV98E DRIVE DRIVE LASER LINK MODEL : CCD-TRV98 IR ON, IC4601 IC5601,5602 (4-32) (4-21) XSIRCS SIG STEADY SHOT MODEL : CCD-TR818/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E SIRCS PWM B/W EVF MODEL : CCD-TR618/TR618E/TR718E/TR728E/TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E COLOR EVF MODEL : CCD-TR818...
3-2. OVERALL BLOCK DIAGRAM (2/2) ( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram. TRV MODEL : CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E TR MODEL : CCD-TR618/TR618E/TR718E/TR728E/TR818 VIDEO LIGHT MODEL : CCD-TR618/TR618E/TR718E/TR728E/TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E COLOR EVF MODEL : CCD-TR818 FP-257 VC-251 BOARD...
(IC402 TR MODEL : CCD-TR618/TR618E/TR718E/TR728E/TR818 VC SO (IC402 A 4.75V D 2.8V 0.52Vp-p A 4.75V A 4.75V 1/6 CCD MODEL : CCD-TR618/TR618E/TR718E/TR728E/TRV49/TRV49E/TRV58/TRV58E VC SI (IC402 1/4 CCD MODEL : CCD-TR818/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E V JACK IN (IC503 R0.4Vp-p MODE NTSC MODEL : CCD-TR618/TR818/TRV49/TRV58/TRV68/TRV78/TRV88/TRV98...
OUT 2B (IC151 DIR0A VM1 VM23 VM4 VDD EVF DO ON POWER D 2.8V MT 4.75V TRV MODEL : CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E TR MODEL : CCD-TR618/TR618E/TR718E/TR728E/TR818 VIDEO LIGHT MODEL : CCD-TR618/TR618E/TR718E/TR728E/TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E STEADY SHOT MODEL : CCD-TR818/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E COLOR EVF MODEL : CCD-TR818 3-11 3-12...
TRV MODEL : CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/ BATT SIG TRV88/TRV98/TRV98E TR MODEL : CCD-TR618/TR618E/TR718E/TR728E/TR818 CAM DD ON CHARGE INH DC PACK SW POWER VIDEO LIGHT MODEL : CCD-TR618/TR618E/TR718E/TR728E/TRV49/TRV49E/TRV58/TRV58E/ INIT CHARGE ON INIT CHARGE ON (SEE PAGE 3-26) LANC OUT TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E LANC OUT FAST CHARGE...
Q354 AUDIO L I/O J201 (TRV MODEL) A/V OUT VIDEO I/O TRV MODEL : CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/ TRV88/TRV98/TRV98E VC RF SWP (IC402 TR MODEL : CCD-TR618/TR618E/TR718E/TR728E/TR818 XCS AU (IC402 VTR/CAMERA VC SI (IC402 LASER LINK MODEL : CCD-TRV98 CONTROL VC SO (IC402...
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E 3-10.B/W EVF BLOCK DIAGRAM ( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram. VF-129 BOARD (B/W EVF MODEL) T902 Q903 Q904 VIDEO VIDEO DRIVE V901 IC901 qh NOT USED...
Page 63
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E 3-11.COLOR EVF BLOCK DIAGRAM ( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram. IC4501 rk IC4501 w; VF-141 BOARD (COLOR EVF MODEL) 7.2Vp-p 0.50Vp-p IC4501 ws VCC1 EVF 2.8V EVF 13.3V...
Page 64
SWITCHING L002 TRV78/TRV78E/TRV88/TRV98/TRV98E L012 EVF PANEL 4.75V EVF PANEL 4.75V TR MODEL : CCD-TR618/TR618E/TR718E/TR728E/TR818 L013 AU 4.75V AU 4.75V B/W EVF MODEL : CCD-TR618/TR618E/TR718E/TR728E/TRV49/TRV49E/ OUTPUT-2 L014 A 4.75V A 4.75V TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E OUTPUT MONITOR-2 L016 RP 4.75V RP 4.75V COLOR EVF MODEL : CCD-TR818...
Page 65
(TR MODEL) REMOTE COMMANDER MODEL : CCD-TR728E/TRV49/TRV49E/TRV59E/TRV78/TRV78E/TRV98/TRV98E CD-281 BOARD VF 129 BOARD LASER LINK MODEL : CCD-TRV98 (TRV MODEL) VIDEO LIGHT MODEL : CCD-TR618/TR618E/TR718E/TR728E/TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E (B/W EVF MODEL) STEADY SHOT MODEL : CCD-TR818/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E VIDEO LIGHT J202 B/W EVF MODEL : CCD-TR618/TR618E/TR718E/TR728E/TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E...
EVF_VG EVF_G XTALLY_LED EVF_R EVF_BL_4.75V EVF_2.8V ND4601 EVF_BL_GND BACK LIGHT EVF_2.8V LB-062 BOARD CN4601 EVF_BL_GND EVF_BL_4.7.5V BL-HIGH TR MODEL :CCD-TR618/TR618E/TR718E/TR728E/TR818 XTALLY_LED TRV MODEL :CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E BL-LOW TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E LED_K CONTROL SWITCH BLOCK CN711 (SS-1000) XCAM+STBY_SW S001 S002 XVTR_MODE_SW PLAYER REG_GND (EXCEPT TR818)
Page 68
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) (For printed wiring boards) (Measuring conditions voltage and waveform) •...
Page 69
C194 LND191 1608 this diagram isn’t mounted in this model. NTSC MODEL :CCD-TR618/TR818/TRV49/TRV58/TRV68/TRV78/TRV88/TRV98 PAL MODEL :CCD-TR618E/TR718E/TR728E/TRV49E/TRV58E/TRV59E/TRV78E/ TRV98E 1/6 CCD MODEL :CCD-TR618/TR618E/TR718E/TR728E/TRV49/TRV49E/TRV58/TRV58E/ TRV59E 1/4 CCD MODEL :CCD-TR818/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E TRV MODEL :CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/ TRV88/TRV98/TRV98E TR MODEL :CCD-TR618/TR618E/TR718E/TR728E/TR818 Precautions Upon Replacing CCD imager • The CD-281/286 board mounted as a repair part is not equipped with a CCD imager.
Page 70
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E MI-040/041 (STEADY SHOT, MIC AMP, IR DRIVE) PRINTED WIRING BOARD — Ref. No. MI-040/041 Board; 10,000 Series — For printed wiring board CD-286 (TR model) • Refer to page 4-70 for parts location. CD-281 (TRV model) • MI-040/041 board consists of multiple layers. However, (CCD IMAGER) only the sides (layers) A and B are shown.
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E For Schematic Diagram • Refer to page 4-9 for printed wiring board. MI-040 BOARD(1/2) (TR MODEL) MI-041 BOARD(1/2) (TRV MODEL) C810 STEADY SHOT,MIC AMP (STEADY SHOT MODEL) -REF.NO.:10000 SERIES- XX MARK:NO MOUNT C772 C777 R785 C762 0.056u 0.056u...
Page 72
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E For Schematic Diagram • Refer to page 4-9 for printed wiring board. • Refer to page 4-66 for waveforms. MI-040 BOARD(2/2) (TR MODEL) NO MARK:REC/PB MODE MI-041 BOARD(2/2) (TRV MODEL) R :REC MODE SIGNAL PATH P :PB MODE...
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E PD-131 (RGB, TIMING GENERATOR, BACK LIGHT) PRINTED WIRING BOARD — Ref. No. PD-131 Board; 10,000 Series — For printed wiring board CD-286 (TR model) • Refer to page 4-70 for parts location. CD-281 (TRV model) • PD-131 board consists of multiple layers. However, only (CCD IMAGER) the sides (layers) A and B are shown.
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E For Schematic Diagram • Refer to page 4-15 for printed wiring board. PD-131 BOARD(2/2) (TRV MODEL) BACK LIGHT Note : Note : The components identified by Les composants identifiés par -REF.NO.:10000 SERIES- L5601 R5601 R5604 mark 0 or dotted line with mark...
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E For Schematic Diagram • Refer to page 4-66 for waveforms. VF-129 BOARD CCD-TR618/TR618E/TR718E/TR728E T902 CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/ TRV78E/TRV88/TRV98/TRV98E B/W EVF -REF.NO.:1000 SERIES- XX MARK:NO MOUNT Q904 2SD1819A-QRS-TX VIDEO DRIVE NO MARK:REC/PB MODE -12.3 R :REC MODE P :PB MODE L902...
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E VF-141 (COLOR EVF) PRINTED WIRING BOARD — Ref. No. VF-141 Board; 10,000 Series — For printed wiring board LB-062 (TR818) • Refer to page 4-71 for parts location. (EVF BACK LIGHT) • VF-141 board consists of multiple layers. However, only the sides (layers) A and B are shown.
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E For Schematic Diagram • Refer to page 4-27 for printed wiring board. • Refer to page 4-67 for waveforms. VF-141 BOARD (CCD-TR818 ONLY) RGB DRIVER/TG -REF.NO.:1000 SERIES- FB4502 C4514 C4513 XX MARK:NO MOUNT 3.3u 0.1u NO MARK:REC/PB MODE...
Page 83
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E CF-077 (SWITCH) PRINTED WIRING BOARD — Ref. No. CF-077 Board; 1,000 Series — For printed wiring board • Refer to page 4-71 for parts location. • CF-077 board consists of multiple layers. However, only the sides (layers) A and B are shown.
Page 84
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E For Schematic Diagram • Refer to page 4-67 for waveform. CF-077 BOARD (CCD-TR618/TR618E/TR718/TR718E/TR818) SWITCH,INDICATOR DRIVE -REF.NO.:1000 SERIES- XX MARK:NO MOUNT S006 RB001 NO MARK:REC/PB MODE SEL/PUSH EXEC R :REC MODE P :PB MODE CN001 KEY_AD2 KEY_AD3 KEY_AD4 BL_GND...
VCC_2 C472, C473, R466, R467, R470, R480 :NTSC MODEL VCC_1 4700P 0.022 :PAL MODEL REG_GND DEW_AD DEW SENSOR NTSC MODEL :CCD-TR618/TR818/TRV49/TRV58/TRV68/TRV78/TRV88/TRV98 PAL MODEL :CCD-TR618E/TR718E/TR728E/TRV49E/TRV58E/TRV59E/TRV78E/TRV98E R462 TR MODEL :CCD-TR618/TR618E/TR718E/TR728E/TR818 FP-356 Q001 1608 FLEXIBLE TRV MODEL :CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/ TAPE TOP R464 TRV98E R461...
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E For Schematic Diagram • Refer to page 4-39 for printed wiring board. • Refer to page 4-69 for waveforms. VC-251 BOARD(7/11) MODE CONTROL(MC BLOCK) -REF.NO.:10000 SERIES- XX MARK:NO MOUNT NO MARK:REC/PB MODE R :REC MODE P :PB MODE...
TALLY_LED IR_FSC EXCEPT TR818 CN715 CN703 TO VF-129 BOARD SIGNAL PATH BW_EVF_4.75V CN901 R3.0/P0 EVF_GND THROUGH THE FFC-256 VIDEO SIGNAL TR MODEL :CCD-TR618/TR618E/TR718E/TR728E/TR818 BW_EVF_Y FLEXIBLE AUDIO TRV MODEL :CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/ XTALLY_LED (SEE PAGE CHROMA Y/CHROMA SIGNAL R0/P0.5 Q701 TRV78/TRV78E/TRV88/TRV98/TRV98E 4-25) LED DRIVE...
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E FP-257 (VIDEO LIGHT, S VIDEO) FLEXIBLE BOARD — Ref. No. FP-257 Flexible board; 10,000 Series — FP-257 FLEXIBLE (VIDEO LIGHT) J201 S VIDEO J202 RFU DC 1-680-198- CONTROL SWITCH BLOCK (SS-1000) FP-257 FP-260 VIDEO LIGHT, S VIDEO 4-65...
Ver 1.1 2001. 04 Before starting adjustment 1-1. Adjusting items when replacing main parts and boards. When replacing main parts, adjust the items indicated by in the following table. Replaced parts Block replacement Parts replacement Adjustment Adjustment Section Initialization of D, Initialization of D, E, F, 7 page data E, F, 7 page data Modification of D, E, F, 7 page data...
Page 109
2, address: A2 to A4 to “00”. Board (Refer to “Record of Use check” of “5-4. SERVICE replacement MODE”) *2: Color EVF model (CCD-TR818) *3: B/W EVF model (CCD-TR618/TR618E/TR718E/ TR728E/TRV49/TRV49E/TRV58/TRV58E/TRV59E/ TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E) *4: TRV model: (CCD-TRV49/TRV49E/TRV58/TRV58E/ TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/ Adjustment...
5-1. CAMERA SECTION ADJUSTMENT 1-1. PREPARATIONS BEFORE ADJUSTMENT (CAMERA SECTION) 1-1-1. List of Service Tools • Oscilloscope • Color monitor • Vectorscope • Regulated power supply • Digital voltmeter Ref. No. Name Parts Code Usage Auto white balance adjustment/check Filter for color temperature correction (C14) J-6080-058-A White balance adjustment/check ND filter 1.0...
Note2: When performing only the adjustments, the lens block and boards need not be disassembled. Note3: CF-077 board, MI-040 board: TR model CF-1000 block, MI-041 board: TRV model TR model: CCD-TR618/TR618E/TR718E/TR728E/TR818 TRV model: CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/ TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E 1.5 m Connect the equipment for adjustments according to Fig. 5-1- 4, 5-1-5.
Page 112
TR model (CCD-TR618/TR618E/TR718E/TR728E/TR818) Note: Use either a AC power adaptor or a Info-LITHIUM battery as the power supply of the CPC jig for BX/BK. CPC jig for BX/BK (J-6082-521-A) AC power adaptor (8.4Vdc) AC-L10 AC-VQ800 etc LANC Terminated at 75...
Page 113
TRV model (CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E) Note: Use either a AC power adaptor or a Info-LITHIUM battery as the power supply of the CPC jig for BX/BK. CPC jig for BX/BK (J-6082-521-A) AC power adaptor (8.4Vdc) AC-L10 AC-VQ800 etc LANC Terminated at 75 jack L series Info LITHIUM...
Note1: Fixed data-1: Initialized data. (Refer to “1. Initializing the D, E, F, 7 Page Data”.) Adjustment page Fixed data-1: Modified data. (Refer to “2. Modification of D, E, F, Adjustment Address 00 to FF 7 Page Data”.) Note: NTSC model: CCD-TR618/TR818/TRV49/TRV58/TRV68/ Initial value Address Remark TRV78/TRV88/TRV98 NTSC PAL PAL model: CCD-TR618E/TR718E/TR728E/TRV49E/TRV58E/...
Page 116
4. F Page table Note1: Fixed data-1: Initialized data. (Refer to “1. Initializing the D, E, F, Initial value Address Remark 7 Page Data”.) NTSC PAL Fixed data-2: Modified data. (Refer to “2. Modification of D, E, F, Fixed data-1 7 Page Data”.) Fixed data-2 55 to 57...
Page 117
Initial value Initial value Address Remark Address Remark NTSC PAL NTSC PAL Flange back adj. Color reproduction adj. DB to DD Fixed data-1 Fixed data-2 F0 to F2 Fixed data-1 Fixed data-2 Fixed data-1 Angular velocity sensor sens. adj. Fixed data-2 F7 to FF Fixed data-1 Fixed data-1...
Page 118
5. E Page Table Note: Fixed data-1: Initialized data. (Refer to “1. Initializing the D, E, F, 7 Initial value Address Remark Page Data”.) NTSC PAL Fixed data-2: Modified data. (Refer to “2. Modification of D, E, F, 7 Fixed data-2 Page Data”.) (Modified data.
CAMERA SYSTEM ADJUSTMENTS Before perform the camera system adjustments, check that the specified values of “VIDEO SYSTEM ADJUSTMENTS” are satisfied. Note: NTSC model: CCD-TR618/TR818/TRV49/TRV58/TRV68/TRV78/TRV88/TRV98 PAL model: CCD-TR618E/TR718E/TR728E/TRV49E/TRV58E/TRV59E/TRV78E/TRV98E 1. Lens Type Input 2. HALL Adjustment Distinguish the type of the lens being used for the camcorder, and For detecting the position of the lens iris, adjust AMP gain and input data corresponding to the type.
3. Flange Back Adjustment (Using Minipattern Box) The inner focus lens flange back adjustment is carried out automatically. In whichever case, the focus will be deviated during auto focusing/manual focusing. Subject Siemens star chart with ND filter for the minipattern box (Note1) Measuring Instrument Adjustment remote commander Adjustment Page...
4. Flange Back Adjustment (Using Flange Back Adjustment Chart and Subject More Than 500m Away) The inner focus lens flange back adjustment is carried out automatically. In whichever case, the focus will be deviated during auto focusing/manual focusing. 4-1. Flange Back Adjustment (1) 4-2.
5. Flange Back Check Subject Siemens star (2.0m from the front of the lens) (Luminance : approx. 200 lux) Measurement Point Check operation on TV monitor Measuring Instrument Specified Value Focused at the TELE end and WIDE end. Note: When the auto focus is ON, the lens can be checked if it is focused or not by observing the data on the page 1 of the adjustment remote commander.
6. Picture Frame Setting Subject Color bar chart (Color reproduction adjustment frame) (1.5m from the front of the lens) Measurement Point Video output terminal Measuring Instrument Oscilloscope and TV monitor Specified Value A=B, C=D, E=F Switch setting: 1) NIGHT SHOT (Lens block) ..........OFF 2) DIGITAL ZOOM (Menu display) ........
Adjustment Address 47, 49, D7, D8 Specified Value All color luminance points should settle within each color reproduction frame. Note: NTSC model: CCD-TR618/TR818/TRV49/TRV58/TRV68/ TRV78/TRV88/TRV98 PAL model: CCD-TR618E/TR718E/TR728E/TRV49E/TRV58E/ TRV59E/TRV78E/TRV98E Switch setting: NIGHT SHOT (Lens block) ..........OFF DIGITAL ZOOM (Menu display) ........OFF STEADY SHOT (Menu display) ........
8. Auto White Balance & LV Standard Data Input Adjust the white balance reference at 3200K, and adjust the normal coefficient of the light value. Subject Clear chart (Color reproduction adjustment frame) Measurement Point Display data of page 1 (Note3) Measuring Instrument Adjustment remote commander Adjustment Page...
Page 127
5E: 1/6 CCD NTSC model B ratio: 5D20 to 5DE0 62: 1/6 CCD PAL model 5D: 1/4 CCD NTSC model Note1: 1/6 CCD NTSC model: CCD-TR618/TRV49/TRV58 5D: 1/4 CCD PAL model 1/6 CCD PAL model: CCD-TR618E/TR718E/TR728E/TRV49E/ TRV58E/TRV59E Write down the data.
10. White Balance Check Subject Clear chart (Color reproduction adjustment frame) Filter Filter C14 for color temperature correction ND filter 1.0 and 0.4 and 0.1 Measurement Point Video output terminal Measuring Instrument Vectorscope Specified Value Fig. 5-1-13. A to B Switch setting: 1) NIGHT SHOT (Lens block) ..........
11. Angular Velocity Sensor Sensitivity Adjustment (CCD-TR818/TRV68/TRV78/TRV78E/TRV88/TRV98/ TRV98E) Precautions on the Parts Replacement There are two types of repair parts. Type A: ENC03JA Type B: ENC03JB Replace the broken sensor with a same type sensor. If replace with other type parts, the image will vibrate up and down or left and right during hand-shake correction operations.
Page 130
1-4. COLOR ELECTRONIC VIEWFINDER SYSTEM ADJUSTMENT (CCD-TR818) Note1: The back light (fluorescent tube) is driven by a high voltage AC power supply. Therefore, do not touch the back light holder to avoid electrical shock. Note2: When replacing the LCD unit, be careful to prevent damages caused by static electricity.
1. RGB AMP Adjustment (VF-141 board) 2. Contrast Adjustment (VF-141 board) Set the D range of the RGB driver used to drive the LCD to the Set the level of the VIDEO signal for driving the LCD to the specified specified value.
3. Backlight Consumption Current Adjustment 4. White Balance Adjustment (VF-141 board) (LB-062 board) Correct the white balance. Set the backlight luminance and color temperature. If deviated, the reproduction of the EVF screen may degenerate. If deviated, the image may become dark or bright. Mode Camera Mode...
1-5-4. Aberration Adjustment 1-5-5. Horizontal Amplitude Adjustment (VF-129 board) Mode VTR stop Mode Playback Signal Dot pattern Signal Alignment tape : For checking operation Specified Value 2 a1 (WR5-5NSP (NTSC)) 0.8 a2 (WR5-5CSP (PAL)) Monoscope section Adjusting method: 1) Adjust the aberration adjustment ring so that the tracing of the Adjusting Element C909 (SOL901) dot satisfies the specified value.
1-6. LCD SYSTEM ADJUSTMENT 1. LCD Type Check By measuring the resistor value between Pin 6 of CN5502 and (CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/ GND, the type of LCD can be discriminated. TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E) Resistor LCD type CCD- Note 1: The back light (fluorescent tube) is driven by a high voltage AC value power supply.
2. VCO Adjustment (PD-131 board) 3. RGB AMP Adjustment (PD-131 board) Set the VCO free-run frequency. If deviated, the LCD screen will Set the D range of the RGB decoder used to drive the LCD to the be blurred. specified value. If deviated, the LCD screen will become blackish or saturated (whitish).
4. Contrast Adjustment (PD-131 board) 5. COM AMP Adjustment (PD-131 board) Set the level of the VIDEO signal for driving the LCD to the specified Set the common electrode drive signal level of LCD to the specified value. If deviated, the screen image will be blackish or saturated value.
Ver 1.1 2001. 04 6. V-COM Adjustment (PD-131 board) 7. White Balance Adjustment (PD-131 board) Set the DC bias of the common electrode drive signal of LCD to the Correct the white balance. specified value. If deviated, the reproduction of the LCD screen may degenerate. If deviated, the LCD display will move, producing flicker and Mode VTR stop...
2-3. TAPE PATH ADJUSTMENT 5-2. MECHANISM SECTION ADJUSTMENT 1. Preparations for Adjustment Mechanism Section adjustments, checks, and replacement of 1) Clean the tape path face (tape guide, capstan shaft, pinch roller). mechanism parts, refer to the separate volume “8mm Video 2) Connect the adjustment remote commander.
5-3. VIDEO SECTION ADJUSTMENTS 3-1. PREPARATIONS BEFORE ADJUSTMENTS Use the following measuring instruments for video section adjustments. 3-1-1. Equipment to Required TV monitor Oscilloscope (dual-phenomenon, band width above 30 MHz with delay mode) (Unless specified otherwise, use a 10 : 1 probe.) Frequency counter Pattern generator with video output terminal...
1) Connect the adjustment remote commander to CN713 of VC- TR model: 251 board or CPC connector of FP-262 flexible via CPC jig CCD-TR618/TR618E/TR718E/TR728E/TR818 for BX/BK (J-6082-521-A). To operate the adjustment remote Color EVF model: commander, connect the AC power adapter to the DC IN jack...
3-1-3. Adjusting Connectors Some of the adjusting points of the video section are concentrated [TRV model] in CN713 of VC-251 board or CPC connector of FP-262 flexible. CN713 Connect the Measuring instruments and the adjustment remote commander via the CPC jig for BX/BK (J-6082-521-A) to CN713 or CPC connector.
3-1-5. Alignment Tape The following table lists alignment tapes which are available. Use the tape specified in the signal column for each adjustment. If the type of tape to be used for checking operations is not specified, use whichever type. Alignment tape Name Recording mode...
3-1-6. Output Level and Impedance 3-1-7. Recording Mode (Standard 8/Hi8) switching Video output The record mode (Standard 8/Hi8) of this unit switches as shown in Stereo minijack, the following table. The playback mode (Standard 8/Hi8) switches 1Vp-p, 75 , unbalanced, sync negative automatically according to the recording mode of the tape played S video output back.
(VC-251 board) Set the frequency of the clock for synchronization. Video system adjustments must be performed in the following order. If deviated, the synchronization will be disrupted and the color will Note: NTSC model:CCD-TR618/TR818/TRV49/TRV58/TRV68/TRV78/ TRV88/TRV98 become inconsistent. PAL model: CCD-TR618E/TR718E/TR728E/TRV49E/TRV58E/...
2. AFC fo Adjustment (VC-251 board) 3. Filter fo Adjustment (VC-251 board) Adjust the pull-in range of the A/D converted clock generator during Adjust the fo frequency of the IC151 built-in filter. playback. Mode VTR stop Mode VTR stop Signal No signal Signal No signal...
4. Y OUT Level Adjustment (VC-251 board) 5. C OUT Level Adjustment (VC-251 board) Set the Y signal output level. (Adjust the D/A converter out put Set the chroma signal output level. (Adjust the D/A converter out level of IC151.) put level of IC151.) Mode VTR stop...
Ver 1.1 2001. 04 6. REC Y Current Adjustment (VC-251 board) Adjusting method: Adjust the Y FM signal recording current. Order Page Address Data Procedure Mode VTR recording (SP mode) Set to the stop mode. Signal No signal Set the data. Measurement Point REC RF (Pin qg of CN713 or Pin qg Write down the data.
7. REC C/AFM Current Adjustment 7-2. REC C Current Check (VC-251 board) Check the recording current level of the REC Chroma signal. If it is 7-1. Preparations too low, chroma signal noise in played back picture will be increased. If too high, Y signal noises will increase and white modulation noises will be produced.
7-3. REC AFM Current Adjustment (VC-251 board) 7-4. Processing after completed adjustment Set the recording levels of the REC AFM signal. If the level is too Order Page Address Data Procedure low, the audio S/N will be deteriorated. If too high, color beets will Set the data.
3-5. IR TRANSMITTER ADJUSTMENTS (CCD- TRV98) Adjust using the IR receiver jig (J-6082-383-A). Note: If the distance between the IR receiver jig and the camcorder is below 1m, cover the LASER LINK emitter with a ND filter. (For example, when the distance is 30cm to 50cm, cover the LASER LINK emitter with a ND filter 1.0.) Switch setting: LASER LINK ........
3. IR Audio Deviation Adjustment (MI-041 board) Mode Playback Signal Alignment tape: For checking operation (WR5-5NSP(NTSC)) Measurement Point AUDIO L terminal and AUDIO R terminal of IR receiver jig (Terminated at 47k ) Measuring Instrument Audio level meter Adjustment Page Adjustment Address Specified Value Signal level: –7.5 ±...
3-6. AUDIO SYSTEM ADJUSTMENTS 1. 1.5MHz Deviation Adjustment (VC-251 board) Adjust to the optimum 1.5MHz audio FM signal deviation. If the adjustment is not correct, its playback level will differ from [Connecting the measuring instruments for the audio] that of other units. Connect the audio system measuring instruments in addition to the video system measuring instruments as shown in Fig.
5-4. SERVICE MODE 4-1. ADJUSTMENT REMOTE COMMANDER 2. Precautions Upon Using the Adjustment Remote Commander The adjustment remote commander is used for changing the calculation coefficient in signal processing, EVR data, etc. The Mishandling of the adjustment remote commander may erase the correct adjustment data at times.
4-2. DATA PROCESS The calculation of the DDS display and the adjustment remote commander display data (hexadecimal notation) are required for obtaining the adjustment data of some adjustment items. In this case, after converting the hexadecimal notation to decimal notation, calculate and convert the result to hexadecimal notation, and use it as the adjustment data.
4-3. SERVICE MODE Note: After the completion of the all adjustments, cancel the service mode by either of the following ways. 1) Unplug the main power supply and remove the lithium battery. (In this case, date and time and menu setting have been set by users are canceled.
2. Emergency Memory Address 2-1. EMG code (Emergency code) The codes shown in the following table which correspond to errors that occur are recorded in addresses 10, 14, and 18. Page F Address 10 to 1B Code Type of Emergency Address Contents No error...
2-2. MSW codes • The lower parts of the data of addresses 12, 16 and 1A represent the MSW codes (mode switch, mechanism position) when errors occurs. • The upper parts of the data of addresses 12, 16 and 1A represent, when the mechanism position is to be moved, the MSW codes at the start of movement (when moving the loading motor).
3. Bit Value Discrimination Bit values must be discriminated using the display data of the Display on the Bit values adjustment remote commander for the following items. Us the table adjustment bit3 bit2 bit1 bit0 below to discriminate if the bit value is “1” or “0”. remote commander bit7...
REVERSE NORMAL (IC4803 ok) (PR-10500) *3 (PR-10500) *3 *1: LASER LINK model (CCD-TRV98) *2: Video light model (CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/ TRV78E/TRV88/TRV98/TRV98E) *3: TRV model (CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E) *4: CF-1000 block: TRV model CF-077 board: TR model 8. Record of Use check Note: When replacing the drum assembly, initialize the data of address: A2 to A4.
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E SECTION 6 REPAIR PARTS LIST 6-1. EXPLODED VIEWS NOTE: • -XX, -X mean standardized parts, so they may • Abbreviation The components identified by mark 0 or have some differences from the original one. CND : Canadian model dotted line with mark 0 are critical for safety.
(See page 6-8 to 6-10) (See page 6-3) BT901 Color EVF model Color EVF section (See page 6-4) Lens section (See page 6-7) TR model :CCD-TR618/TR618E/TR718E/TR728E/TR818 TRV model :CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E B/W EVF model :CCD-TR618/TR618E/TR718E/TR728E/ TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E Color EVF model :CCD-TR818 Ref. No.
: BT001(Lithium battary) CF board on the mount position. (See page 4-36/TR model) [In the TRV model, the printed wiring board of the control switch block (CF-1000) on which lithium battery is mounted, is not shown.] TR model :CCD-TR618/TR618E/TR718E/TR728E/TR818 TRV model :CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E 2.5 inch LCD model...
6-1-6. LCD SECTION (TRV MODEL) (TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E) 2.5 inch LCD model LCD901 ND901 3.0 inch LCD model 3.5 inch LCD model LCD901 ND901 LCD901 ND901 2.5 inch LCD model :CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E 3.0 inch LCD model :CCD-TRV88 3.5 inch LCD model :CCD-TRV98/TRV98E Ref. No. Part No.
CD-286 CD-281 CF-077 6-2. ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • RESISTORS When indicating parts by reference number, parts list may be different from the parts All resistors are in ohms. please include the board name. specified in the diagrams or the components METAL: metal-film resistor The components identified by mark 0 or...
Page 190
FOR CAMERA COLOR REPRODUCTION ADJUSTMENT For NTSC model CCD-TR618/TR818/TRV49/TRV58/ Take a copy of CAMERA COLOR TRV68/TRV78/TRV88/TRV98 REPRODUCTION FRAME with a clear sheet for use. For PAL model CCD-TR618E/TR718E/TR728E/TRV49E/ TRV58E/TRV59E/TRV78E/TRV98E — 239 —...
Page 192
CCD-TR618/TR618E/TR718E/TR728E/TR818 CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/ TRV78/TRV78E/TRV88/TRV98/TRV98E RMT-708 US Model CCD-TR818/TRV58/TRV68/TRV88/TRV98 Canadian Model CCD-TR818/TRV58/TRV68/TRV98 AEP Model UK Model CCD-TR718E/TR728E/TRV58E/ SERVICE MANUAL TRV59E/TRV78E/TRV98E E Model CCD-TR618/TR618E/TR818/TRV49/ TRV49E/TRV58/TRV68/TRV78/ TRV78E/TRV88/TRV98/TRV98E Australian Model CCD-TR618E/TRV49E/TRV78E/TRV98E 2001. 11 Hong Kong Model CCD-TR618E/TRV49/TRV49E/TRV78/ TRV78E/TRV98/TRV98E Tourist Model CCD-TRV49/TRV49E/TRV78/ TRV78E/TRV98/TRV98E Chinese Model CCD-TR618E/TRV49E/TRV98E...
Page 193
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E Discrimination of the CCD imager type TABLE OF CONTENTS PRINTED WIRING BOARDS AND Method 1: The check method using the adjustment remote SCHEMATIC DIAGRAMS commander. 4-2. PRINTED WIRING BOARDS AND 1) Select page: 6, address: 04, and check the data.
Page 194
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E SECTION 4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) (Measuring conditions voltage and waveform) (For printed wiring boards) •...
Page 195
R8.5/P0 R193 C194 LND191 1608 NTSC MODEL :CCD-TR618/TR818/TRV49/TRV58/TRV68/TRV78/TRV88/TRV98 PAL MODEL :CCD-TR618E/TR718E/TR728E/TRV49E/TRV58E/TRV59E/TRV78E/ TRV98E 1/6 CCD MODEL :CCD-TR618/TR618E/TR718E/TR728E/TRV49/TRV49E/TRV58/TRV58E/ TRV59E 1/4 CCD MODEL :CCD-TR818/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E TRV MODEL :CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/TRV78/TRV78E/ TRV88/TRV98/TRV98E TR MODEL :CCD-TR618/TR618E/TR718E/TR728E/TR818 TYPE M MODEL :CCD-TRV68/TRV78/TRV88/TRV98 Precautions Upon Replacing CCD imager • The CD-281/286 board mounted as a repair part is not equipped with a CCD imager.
Page 196
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E MOUNTED PARTS LOCATION no mark : side A * mark : side B VC-261 BOARD * C001 E-12 C126 * C284 E-14 * C407 C-13 D001 * L155 C-16 * R021 E-11 R182 * R458 B-11 * RB509 E-11...
Page 199
PAL MODEL :CCD-TR618E/TR718E/TR728E/ L271 C297 TRV49E/TRV58E/TRV59E/ 10uH TRV78E/TRV98E NTSC MODEL :CCD-TR618/TR818/TRV49/TRV58/ TRV68/TRV78/TRV88/TRV98 1/4 CCD MODEL :CCD-TR818/TRV68/TRV78/ RB272 47KX4 TRV88/TRV98/TRV98E 1/6 CCD MODEL :CCD-TR618/TR618E/TR718E/ XCH_SCK DRVDD IC272 XSCK TR728E/TRV49/TRV49E/ CH_SO DRVSS TRV58/TRV58E/TRV59E XCS_CH V_STOP DVSS S/H AGC A/D CONVERTER V_STOP SYS_V...
Page 200
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E < Page 4-45, 4-46 > For Schematic Diagram • Refer to page 7 for printed wiring board. VC-251 BOARD(2/11) CL224 FB152 Y/C PROCESSOR (CL BLOCK) D_2.8V FB153 D_1.5V -REF.NO.:10000 SERIES- L152 10uH C184 XX MARK:NO MOUNT L154 10uH 0.1u...
Page 201
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E < Page 4-47, 4-48 > For Schematic Diagram • Refer to page 7 for printed wiring board. VC-251 BOARD(3/11) FOCUS/ZOOM MOTOR DRIVE(LD BLOCK) R313 R314 2200 -REF.NO.:10000 SERIES- HALL_REF R318 R317 XX MARK:NO MOUNT C309 0.22u C311 NO MARK:REC/PB MODE...
Page 202
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E < Page 4-49, 4-50 > For Schematic Diagram • Refer to page 7 for printed wiring board. VC-251 BOARD(4/11) REC/PB AMP(RP BLOCK) RP_4.75V TO(10/11) REG_GND -REF.NO.:10000 SERIES- PB_RF L103 XX MARK:NO MOUNT REC_L_CONT 22uH REC_L_CONT Q106 REC_Y/MT_CONT NO MARK:REC/PB MODE...
Page 203
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E < Page 4-51, 4-52 > For Schematic Diagram • Refer to page 7 for printed wiring board. VC-251 BOARD(5/11) NO MARK:REC/PB MODE R :REC MODE LINE IN/OUT AMP(IO BLOCK) P :PB MODE -REF.NO.: 10000 SERIES- XX MARK:NO MOUNT FB221 D_2.8V...
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E SECTION 5. ADJUSTMENTS : Added portion. Page Type S Before starting adjustment 1-1. Adjusting items when replacing main parts and boards. When replacing main parts, adjust the items indicated by in the following table. Replaced parts Block replacement...
Page 211
2, address: A2 to A4 to “00”. Board (Refer to “Record of Use check” of “5-4. SERVICE replacement MODE”) *2: Color EVF model (CCD-TR818) *3: B/W EVF model (CCD-TR618/TR618E/TR718E/ TR728E/TRV49/TRV49E/TRV58/TRV58E/TRV59E/ TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E) *4: TRV model: (CCD-TRV49/TRV49E/TRV58/TRV58E/ TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/ Adjustment...
Page 212
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E : Added portion. : Changed portion. Page Type M Type S 4. F Page table 4. F Page table Note1: Fixed data-1: Initialized data. (Refer to “1. Initializing the D, Note1: Fixed data-1: Initialized data. (Refer to “1. Initializing the D, E, F, 7 Page Data”.)
Page 213
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E : Added portion. : Changed portion. Page Type M Type S 5. E Page Table 5. E Page Table Note: Fixed data-1: Initialized data. (Refer to “1. Initializing the D, E, Note1: Fixed data-1: Initialized data. (Refer to “1. Initializing the D, F, 7 Page Data”.)
Type S 1-3. CAMERA SYSTEM ADJUSTMENTS Before perform the camera system adjustments, check that the specified values of “VIDEO SYSTEM ADJUSTMENTS” are satisfied. Note: NTSC model:CCD-TR618/TR818/TRV49/TRV58/TRV68/ TRV78/TRV88/TRV98 PAL model: CCD-TR618E/TR718E/TR728E/TRV49E/ TRV58E/TRV59E/TRV78E/TRV98E 0. CCD Imager Type Input (CCD-TRV68/TRV78/TRV88/TRV98 (NTSC)) only Distinguish the type of the CCD imager used for the camcorder, and input data corresponding to the type.
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E : Added portion. Page Type M Type S 7. Color Reproduction Adjustment Adjust the color Separation matrix coefficient so that proper color reproduction is produced. For NTSC model For NTSC model (CCD type S) Burst position Burst position...
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E : Added portion. Page Type M Type S 9. Auto White Balance Adjustment Adjust to the proper auto white balance output data. If it is not correct, auto white balance and color reproducibility will be poor. Subject Clear chart...
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E 6-2. ELECTRICAL PARTS LIST : Added portion. Page Type M Type S Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks CD-286 BOARD, COMPLETE CD-286 BOARD, COMPLETE *********************** *********************** (IC191 is not included in this mounted board) (IC191 is not included in this mounted board) <...
Page 221
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E Type M Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C473 1-107-819-11 CERAMIC CHIP 0.022uF CN713 1-774-711-41 CONNECTOR, BOARD TO BOARD 20P (TR618E/TR718E/TR728E/TRV49E/ * CN715 1-778-283-11 CONNECTOR, FFC/FPC 4P (EXCEPT TR818) TRV58E/TRV59E/TRV78E/TRV98E) C474 1-125-777-11 CERAMIC CHIP 0.1uF...
Page 222
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E Type M Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < IC > L224 1-469-525-91 INDUCTOR 10uH L271 1-469-570-21 INDUCTOR 10uH IC001 8-752-090-20 IC CXA3057R-T6 L272 1-469-525-91 INDUCTOR 10uH IC101 8-752-093-69 IC CXA3265R-T4 L301...
Page 223
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E Type M Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks Q101 8-729-047-19 TRANSISTOR 2SA1965-S-TL < RESISTOR > Q102 8-729-042-26 TRANSISTOR 2SB1462J-QR(K8).SO (TRV68/TRV78/TRV88/TRV98) R001 1-216-837-11 METAL CHIP 1/16W Q102 8-729-052-65 TRANSISTOR 2SA1774HT2L R002 1-216-839-11 METAL CHIP...
Page 224
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E Type M Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R045 1-218-887-11 METAL CHIP 0.5% 1/10W R156 1-216-825-11 METAL CHIP 2.2K 1/16W (TR818/TRV78E/TRV98E) (TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/ R046 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W TRV78/TRV78E/TRV88/TRV98/TRV98E) (TRV68/TRV78/TRV88/TRV98) R157 1-216-825-11 METAL CHIP 2.2K...
Page 225
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E Type M Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R195 1-216-835-11 METAL CHIP 1/16W R379 1-216-820-11 METAL CHIP 1/16W R196 1-216-835-11 METAL CHIP 1/16W R382 1-216-841-11 METAL CHIP 1/16W R197 1-216-834-11 METAL CHIP...
Page 226
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E Type M Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R521 1-218-911-11 METAL CHIP 470K 0.5% 1/16W < COMPOSITION CIRCUIT BLOCK > R525 1-216-821-11 METAL CHIP 1/16W R531 1-216-833-11 METAL CHIP 1/16W RB101 1-239-702-81 RESISTOR, NETWORK 22K...
Page 227
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E FOR CAMERA COLOR REPRODUCTION ADJUSTMENT For NTSC model TYPE S Take a copy of CAMERA COLOR CCD-TR618/TR818/TRV49/TRV58/ REPRODUCTION FRAME with TRV68/TRV78/TRV88/TRV98 a clear sheet for use. For NTSC model TYPE M CCD-TRV68/TRV78/TRV88/TRV98 — 50 —...
Page 228
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E FOR CAMERA COLOR REPRODUCTION ADJUSTMENT For PAL model Take a copy of CAMERA COLOR REPRODUCTION FRAME with a clear sheet for use. CCD-TR618E/TR718E/TR728E/TRV49E/ TRV58E/TRV59E/TRV78E/TRV98E — 51 —...
Page 230
CCD-TR618/TR618E/TR718E/TR728E/TR818 CCD-TRV49/TRV49E/TRV58/TRV58E/TRV59E/TRV68/ TRV78/TRV78E/TRV88/TRV98/TRV98E RMT-708 US Model CCD-TR818/TRV58/TRV68/TRV88/TRV98 Canadian Model CCD-TR818/TRV58/TRV68/TRV98 AEP Model UK Model CCD-TR718E/TR728E/TRV58E/ SERVICE MANUAL TRV59E/TRV78E/TRV98E E Model CCD-TR618/TR618E/TR818/TRV49/ TRV49E/TRV58/TRV68/TRV78/ TRV78E/TRV88/TRV98/TRV98E Australian Model CCD-TR618E/TRV49E/TRV78E/TRV98E Ver 1.3 2002. 03 Hong Kong Model CCD-TR618E/TRV49/TRV49E/TRV78/ TRV78E/TRV98/TRV98E Tourist Model CCD-TRV49/TRV49E/TRV78/ TRV78E/TRV98/TRV98E Chinese Model...
Page 231
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E SECTION 5. ADJUSTMENTS 5-1. CAMERA SECTION ADJUSTMENT : Added portion. Page Before change After change 1-6. LCD SYSTEM ADJUSTMENT 1-6. LCD SYSTEM ADJUSTMENT (CCD-TRV49/TRV49E/TRV58/TRV58E/ (CCD-TRV49/TRV49E/TRV58/TRV58E/ TRV59E/TRV68/TRV78/TRV78E/TRV88/ TRV59E/TRV68/TRV78/TRV78E/TRV88/ TRV98/TRV98E) TRV98/TRV98E) 1. LCD Type Check 1. LCD Type Check By measuring the resistor value between Pin 6 of CN5502 and By measuring the resistor value between Pin 6 of CN5502 and GND, the type of LCD can be discriminated.
Page 232
CCD-TR618/TR618E/TR718E/TR728E/TR818/TRV49/TRV49E/TRV58/ TRV58E/TRV59E/TRV68/TRV78/TRV78E/TRV88/TRV98/TRV98E SECTION 6. REPAIR PARTS LIST 6-1. EXPLODED VIEWS : Added portion. Page After change Before change Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks A-7074-667-A PD-131 (S-3.5) BOARD, COMPLETE A-7074-667-A PD-131 (S-3.5) BOARD, COMPLETE...
Reverse 992985814.pdf Revision History S.M. Rev. Ver. Date History Contents issued 2000.12 Official Release — — 2001.04 Correction Correction of adjusting procedure. S.M. correction: Page 5-2, 5-3, 5-5, 5-33, 5-40, 5-44 2001.11 Supplement-1 • The change of the CCD imager of the CCD- (PV01-033) TRV68/TRV78/TRV88/TRV98 (NTSC model) from type S to type M.