B. Print Mode; Selecting A Setting For A User Program - Sharp AL-1661CS Service Manual

Program
Program name
number
16 SOUND AT
DEFAULT
17 TONER SAVE
MODE
18 AE LEVEL ADJUST
19 LANGUAGE
20 RESET FACTORY
21 SORT AUTO
SELECTION

B. Print mode

Program
Program name
number
1 FORCED OUTPUT
2 USB 2.0 MODE
1
SWITCH *
1
* : The scanning speed increases when the USB 2.0 mode is set to "HI-SPEED", however, the printing speed does not increase considerably.

2. Selecting a setting for a user program

1) Press the [MENU] key and then press the [ENTER] key.
In printer mode, the user programs are accessed by simply press-
ing the [MENU] key.
MAIN MENU
1:USER PROGRAM
] >
2) Press the [<] key [v or [ ] key [
to configure in the USER PROGRAM items, and then press the
[ENTER] key.
• You can also select a program by directly entering the program
number with the numeric keys.
USER PROGRAM
2:PREHEAT MODE
< >
3) Press the [ ] key [v] or [
selected item.
PREHEAT MODE
1:30 SEC.
NOTE:
• If you mistakenly select the wrong item, press the [CLEAR] key [C]
and repeat the procedure from step 2.
• To cancel a setting for a user program, press the [MENU] key.
Setting codes
(factory default setting
appears in bold)
1: ON
2: OFF
1: ON
2: OFF
1: SPF/RSPF
2: DOCUMENT GLASS
1: AMERICAN ENGLISH This is used to set the language used in the display.
1: Yes
2: No
1: ON
2: OFF
Setting codes
(factory default setting
appears in bold)
1: ON
2: OFF
1: FULL-SPEED
2: HI-SPEED
^]
to select the item that you wish
] key [^] to change the setting of the
AL-1661CS USER PROGRAM 11 - 2
• Use this to sound a beep when a base setting is selected.
• This mode reduces toner usage by about 10% when copying. Toner save mode is
effective when the exposure mode is AUTO or TEXT.
• This is used to adjust the exposure level.
• The automatic exposure level can be adjusted separately for the document glass
and the RSPF.
This is used to return all settings to the factory default settings.
Used to sort SPF/RSPF copies automatically.
When this function is enabled, printing in printer mode will automatically continue
using a different size of paper if the specified size of paper runs out in all trays. This
feature does not function in copy mode.
This sets the USB 2.0 data transfer speed. To obtain the fastest speed when using
the USB 2.0 port, first verify that your computer meets the system requirements
(operating system and driver), and then use this program to change the USB 2.0
mode to "Hi-Speed". Note that the setting should not be changed while running a
TWAIN driver. (For the system requirements.)
4) Press the [ENTER] key.
Your selection appears briefly and then the previous screen
appears.
NOTE:
When "AE LEVEL ADJUST" is selected in the user programs and the
[ENTER] key is pressed, the automatic exposure adjustment screen
appears. Adjust the exposure and press the [ENTER] key.
Audible signals (key entry beep, invalid key beep, base setting
beep)
The machine sounds three different types of beep signals: a key
entry beep that sounds when a valid key is pressed, an invalid key
beep that sounds when an invalid key is pressed, and a base setting
beep that sounds when a setting is the same as the base setting
(base settings are explained below). The base setting beep is initially
disabled. If you wish to enable the base setting beep, see "SOUND
AT DEFAULT". If you wish to change the volume of the beep signals
or disable them, see "KEY TOUCH SOUND".
The beep patterns of each type of beep signal are as follows:
Key entry beep: One beep
Invalid key beep: Two beeps
Base settings
The base settings are preset standard selections for each copy set-
ting. The base settings are as follows:
Copy ratio: 100%
Light and Dark level: center
Explanation
Explanation
Base setting beep: Three beeps
Paper feed location: Paper tray
AUTO/TEXT/PHOTO: AUTO