Sharp AL-1661CS Service Manual page 27

10) Check the packages on the screen, and then click the "Start" but-
ton.
The software packages to be installed will be displayed on the
screen. If an incorrect package is displayed, click the "Back" but-
ton and select the correct packages.
11) The files required for installation of the MFP driver are copied (if
"MFP Driver" was selected).
Follow the on-screen instructions.
Caution: If you are running Windows 2000/XP and a warning message
appears regarding the Windows logo test or digital signature,
be sure to click "Continue Anyway" or "Yes".
When "The installation of the SHARP software is complete"
appears, click the "OK" button.
12) Begin the installation of Button Manager (if "Button Manager" was
selected).
Follow the on-screen instructions.
Click the "Finish" button when the message informs you that setup
is successful.
The Sharpdesk installer will start.
13) Begin the installation of Sharpdesk (if "Sharpdesk" was selected).
Follow the on-screen instructions.
Click the "Finish" button when the message informs you that
Setup is complete.
Caution: In Windows 98/Me/2000, if the following screen appears,
click the "Skip" button or the "Continue" button as appropriate
to continue the Sharpdesk installation.
If "Skip" is selected, the Sharpdesk installation will continue
without installing Sharpdesk Imaging.
If "Continue" is selected, Sharpdesk Imaging will be installed.
If Imaging for Windows is installed on your computer, Sharp-
desk
Imaging will overwrite Imaging for Windows.
14) When the "Finish" screen appears, click the "Close" button.
Caution: If you are running Windows 2000/XP and a warning message
Note:
• If this is a "Standard" installation, the "Finish" screen will appear
• After the installation, a message prompting you to restart your com-
15) Make sure that the power of the machine is turned on, and then
Caution: If the following message appears on your computer screen,
16) Begin installation of the scanner driver.
Caution: If you are running Windows 2000/XP and a warning message
Note: A "USB 2.0 Composite Device" installation window may appear
17) Begin installation of the printer driver.
Caution: If you are running Windows 2000/XP and a warning message
18) Follow the instructions in the Plug and Play screen that appears in
This completes the installation of the software.
• If you installed Button Manager, set up Button Manager as explained
(2) Connecting a USB cable
Follow the procedure below to connect the machine to your computer.
A USB cable for connecting the machine to your computer is not
included with the machine. Please purchase the appropriate cable for
your computer.
Caution:
• USB is available with a PC/AT compatible computer that was origi-
• Do not connect the USB cable before installing the MFP driver. The
AL-1661CS UNPACKING AND INSTALLATION 5 - 5
appears regarding the Windows logo test or digital signature,
be sure to click "Continue Anyway" or "Yes".
A message will appear instructing you to connect the machine to
your computer. Click the OK button.
after several minutes.
puter may appear. In this case, click the "Yes" button to restart your
computer.
connect the USB cable.
Windows will detect the machine and a Plug and Play screen will
appear.
close it.
A window regarding "HI-SPEED USB Device" will then
appear. Close the window.
This message appears when the machine's USB 2.0 mode is
not set to "HI-SPEED". For information on switching the USB
2.0 mode.
"SHARP AL-XXXXCS" will appear in the "Found New Hardware
Wizard" dialog box. Select "Install the software automatically
(Recommended)" and click the "Next" button. Follow the on-
screen instructions.
appears regarding the Windows logo test or digital signature,
be sure to click "Continue Anyway" or "Yes".
prior to this procedure. In this case, follow the instructions in the
window to install the USB 2.0 Composite Device.
"SHARP AL-XXXXCS" will appear in the "Found New Hardware
Wizard" dialog box. Select "Install the software automatically
(Recommended)" and click the "Next" button. Follow the on-
screen instructions.
appears regarding the Windows logo test or digital signature,
be sure to click "Continue Anyway" or "Yes".
your version of Windows to begin the installation.
in "SETTING UP BUTTON MANAGER".
nally equipped with USB and had Windows 98, Windows Me, Win-
dows 2000 Professional, Windows XP Professional or Windows XP
Home Edition preinstalled.
USB cable should be connected during installation of the MFP
driver.