ANY MODIFICATIONS TO THE APPLIANCE THAT ARE PERFORMED WITHOUT THE WRITTEN PERMISSION OF MEIKO WILL IMMEDIATELY VOID THE MANUFACTURER’S WARRANTY. Meiko reserves the right to change any specifications without notice at any time. Meiko • 917 Airpark Center Drive • Nashville, TN 37217 Phone: (615) 399-6600 •...
The following symbols and headings are used 1.1 Overview of Equipment throughout this manual to indicate possible The Meiko Model DV 200.2 is a commercial hazards to persons or to the equipment. The dishwasher designed for cleaning dishes, symbols and headings are shown in order of glassware, trays, cutlery and kitchen utensils importance.
The area MUST have a firm floor The appliance’s warranty is not valid until a surface. It is possible to compensate for Meiko Authorized Service Agent performs a uneven flooring by adjusting the feet. Startup and Demonstration on the appliance.
1-800-868-3840, providing full details on the ribbon cable to customer, serial number and extent of damage Mike 2 controller present. Meiko will file a freight claim based on Remove 2 screws on this information. bottom edge 3. Move the appliance to the installation area and remove the skid.
3 - I ECTION NSTALLATION 3.5 Main Electrical Supply Connection 2. Check that the incoming power leads are long enough to permit the unit to be WARNING! repositioned for servicing. Check that the circuit breaker/fused disconnect is in the OFF position and 3.
3 - I ECTION NSTALLATION 3.6 Dispensing system overview Figure 3-7: Chemical connections The DV 200.2 is designed for use with a liquid rinse aid, and either solid or liquid detergents. Units equipped with optional liquid internal detergent and rinse aid pumps have two tubes exiting the machine at the lower rear.
3 - I ECTION NSTALLATION CAUTION Figure 3-8: Sealing unused chemical tubes (if If the unit will NOT use one or both of not using a liquid detergent or rinse additive) the chemical supply tubes, cut the unused tube(s) close to the point where it exits the machine’s exterior tubing panel and seal it using the supplied...
3 - I ECTION NSTALLATION 3.8 Installing an External Liquid Rinse Aid Figure 3-10: Liquid rinse additive system System A pre-plumbed, blue 1/4” ID tube at the lower rear of the unit serves as the connection point for the rinse aid supply. See Figure 3-10. If a liquid rinse aid system will NOT be used, cut the tubing near the rear panel.
3-12, be sure to use the supplied wire correctly installed according to the clamps to fasten the chemical supply manufacturer’s instructions. tubes securely. Meiko STRONGLY 3. If the dishwasher is equipped with factory RECOMMENDS the use of a sealing internal chemical dispensing pumps, two...
(with a reducing valve). 2. Check the type of drain that will be used. 3. Check the incoming water temperature. Because the DV 200.2 uses a pumped drain, Meiko recommends a water temperature either a floor or wall drain is acceptable.
ECTION NSTALLATION 3.13 Tabling Attachment Figure 3-15: Straight-through and corner tabling configurations The DV 200.2 can be positioned in either of two tabling configurations; straight through, or in a corner installation. See Figure 3-15. 1. IF the machine will be...
Page 13
3 - I ECTION NSTALLATION CAUTION Figure 3-17: Tabling attachment After adjusting the height of the machine, Lip-in flange MUST always check that it is level to ensure be flush against the proper operation. vertical mounting surface 3. Position each table lip-in at the machine, as shown in Figure 3-17.
6. Press the key to start priming the liquid SETTINGS ARE TO BE PERFORMED detergent lines. A timer will count down ONLY BY A MEIKO AUTHORIZED SERVICE AGENT. CHANGES BY the time remaining. By default, the system UNAUTHORIZED PERSONNEL WILL will prime for 30 seconds.
4 - O ECTION PERATION PERATION 4.1 Location and Description of Controls The dishwasher controls are on the keypad on the front panel. See Figure 4-1. Figure 4-1: Dishwasher controls A, B, C - POWER/CYCLE SELECT keys E - POWER OFF key These keys turn the dishwasher on.
4 - O ECTION PERATION 4.2 Startup 4.3 Loading The loading guidelines shown here will lead Check the level of the external detergent and to faster, more efficient cleaning of your ware. rinse additive dispensers. If necessary, replace or refill the dispensers. Load plates, soup bowls, etc.
• Press the key to stop the wash/rinse screens. Meiko recommends that the door of cycle before opening the door. the dishwasher be left open overnight to allow it to air thoroughly.
Active Plus filter. washer. Note the following: The Active Plus filter MUST be rein- 5. Meiko recommends that the door of the stalled with the slotted end facing dishwasher be left open overnight to allow DOWN. See Figure 5-1.
Lime scale deposits will occur over time on the interior of the dishwasher if it is operated WARNING! using a hard water supply. Meiko recommends Ensure that ALL residue of the a hardness of 4 grains per U.S. gallon (7 DH deliming agent is removed.
“kinks” or pinching. Also check that the water supply is turned on. Meiko Authorized Service Agent You should contact your • The dishwasher encounters a problem but does not display an error code, OR •...
Page 24
If you need service... Meiko warewashers are designed for solid reliability as much as for outstanding ware-cleaning ability. With proper care, your warewasher should provide years of trouble-free operation. If service is necessary, contact your local Meiko Authorized Service Agent. With factory training, OEM parts and direct support from the factory, Meiko’s nationwide service network is highly qualified to quickly...