Advertisement
IN1508 — Setup Guide (cont'd)
Step 4 — RS-232
RS-232 —Connect a control system or
a.
computer to the rear panel RS-232 port.
The IN1508 User's Manual, at
details Simple Instruction Set (SIS
Front Panel and Remote Control Controls and Indicators
Many of the switcher's functions are available via simple controls on the front panel. Front panel LEDs provide indications
of some of the basic system functions. For more complex tasks, such as system configuration, the switcher has a menu system
that is operated by using the front panel buttons. The menu system reports via an on-screen display on the connected output
device.
a
Input buttons and LEDs —
Press to select an input to scale and
output. The lit Input LED indicates
the selected input.
b
Output Rate button and LEDs —
Press to cycle through 12 common
resolutions at the 60 Hz refresh rate. The LEDs indicate the selected resolution.
N Some rates cannot be selected using this button. Use the menu system for additional rates.
c
PIP On (picture-in-picture) button and LED — Press to toggle the PIP feature on and off. The LED lights when PIP
mode is on.
d
PIP Swap button — Press when the PIP feature is on to swap the main and PIP images.
e
Picture Control buttons — Press to change the centering, size, contrast, brightness, color, or tint.
f
Menu control buttons
Menu button — Press to activate the on-screen display menu system (shown below) or to back up one level from the
currently selected menu or submenu.
, , , and
buttons — Press to move the highlight bar over submenus or selections and to adjust selected settings.
Enter button — Press to select a highlighted submenu or selection.
Menu system operation
At right is a a flowchart of the submenus in the
main menu system. Each submenu leads to a series
of submenus or to a "slider" type status indicator
for individual settings.
Setup
Use the front panel menu controls and the
connected display's on-screen display to set up the
IN1508 using the following procedures.
N If no image can be seen on the display, use
the front panel Output Rate button to select
1024x768 or 720p.
You can toggle between an RGBHV and high
definition component video output by pressing
and holding the PIP On button while you
cycle the IN1508 power.
Set output signal settings
1.
Navigate to the Output submenu selection boxes.
2.
Press
and
3.
For each selection box, press
N Some resolutions such as 1920x1200 and 1080p Sharp are only available via SIS command; refer to the IN1508 User's
Manual, available at www.extron.com, for the associated commands.
2
IN1508 • Setup Guide
www.extron.com
) commands.
™
IR
to select among the Resolution, Refresh Rate, Signal Polarity, and Signal Type selection boxes.
and
to select the settings that match the display's native settings.
Step 5 —
RS-232
AC power connector — Plug in a standard IEC
power cord from a 100 to 240 VAC, 50-60 Hz
power source into this receptacle. Turn on the
input and output devices after you power up
the switcher.
INPUT
1
2
3
4
5
6
7
8
1
No
menu
display
Menu
Menu
EXTRON ELECTRONICS IN1508 SCALING PRESENTATION SWITCHER
Enter
INPUT
Enter
PICTURE
Select
Enter
OUTPUT
Enter
AUDIO
Enter
ADVANCED
Power
OUTPUT RATE
PIP
PICTURE CONTROLS
CONT/
ON
SWAP
CENTER
SIZE
BRT
VGA
1024x852
UXGA
SVGA
1024x1024
720p
XGA
1366x768
1080i
SXGA
1365x1024
1080p
2
3
4
5
Center
Center
Zoom
Zoom
Size
Size
Pan
Pan
Brightness
Brightness
+64
Contrast
Contrast
+45
Color
Color
+64
Tint
Tint
+64
Sharpness
Sharpness
+64
Resolution
Resolution
Sync Polarity
Sync Polarity
Refresh Rate
Refresh Rate
Signal Type
Signal Type
Output Volume
Output Volume
Audio Delay
Audio Delay
Input Gain/Atten
Input Gain/Atten
Freeze
Freeze
Swap
Swap
Blank
Blank
PIP Mode
PIP Mode
100-240V
50-60Hz
50/60Hz
IN1508
SCALING PRESENTATION SWITCHER
COL/
TNT
MENU
ENTER
6
Timeout
Aspect
Aspect
Input 5
Input 5
Advanced
Advanced
Fade Switch
Fade Switch
Test Pattern
Test Pattern
Blue Mode
Blue Mode
Reset
Reset
Advertisement
