Step 3: Tv Hookups; Step 4: Playing A Disc; Hookups; Hooking Up The Player - Sony DVP-NS305 Service Manual

Step 3: TV Hookups

Connect the supplied audio/video cord and the power cord in the order (1~3) shown below.
Be sure to connect the power cord last.
If you are connecting to a VCR and your TV has
only one available input jack* (DVP-NS415 only)
to LINE IN to LINE IN
L/R (AUDIO) (VIDEO)
to video
output
LINE
IN R-AUDIO-L VIDEO
IN
OUT
DIGITAL OUT LINE COMPONENT
OUT R-AUDIO-L VIDEO
VIDEO OUT
PCM/DTS/ IN R-AUDIO-L VIDEO
S VIDEO
DOLBY DIGITAL
OUT
COAXIAL OPTICAL
OUT R-AUDIO-L VIDEO
to LINE OUT
to LINE OUT
(VIDEO)
L/R (AUDIO)
to video input
1
Audio/video cord
(supplied)
to audio input
* If you are connecting a VCR and your TV
has only one available input jack
(DVP-NS415 only)
If your TV has only one available input jack,
connect your VCR or similar device to the
LINE IN jacks on the player. In order to view
the pictures from your VCR, the DVD player
must be in standby mode. Note that the DVD
player will only pass signals through the
LINE jacks and will not output the VCR
signals from any other jack.
If your TV has more than one available input
jack, connect your VCR directly to your TV.
16

Hookups

Hooking Up the Player

Follow Steps 1 to 4 to hook up and adjust the settings of the player.
Before you start, disconnect the power cords, check that you have all of the supplied accessories,
and insert the batteries into the remote (page 15).
Notes
• Plug cords securely to prevent unwanted noise.
• Refer to the instructions supplied with the components to be connected.

Step 1: Connecting the Video Cords

Connect this player to your TV monitor, projector, or AV amplifier (receiver) using a video cord.
Select one of the patterns A through C, according to the input jack on your TV monitor,
projector, or AV amplifier (receiver).
A
Audio/video cord
(yellow)
INPUT
(supplied)
Component video cord
VIDEO
(not supplied)
L
AUDIO
R
TV, projector or AV
amplifier (receiver)
(yellow)
to LINE OUT (VIDEO)
DIGITAL OUT LINE COMPONENT
VIDEO OUT Y
PCM/DTS/ IN R-AUDIO-L VIDEO
S VIDEO
DOLBY DIGITAL
OUT
COAXIAL OPTICAL P B
P
R
OUT R-AUDIO-L VIDEO
S VIDEO cord
(not supplied)
l : Signal flow
18
to audio
output
VCR
CD/DVD Player
Y
P B
P
R
3
Power source
TV
INPUT
VIDEO
L
AUDIO
R
2
Power source
When connecting to a wide screen TV
Depending on the disc, the image may not fit
your TV screen.
If you want to change the aspect ratio, please
refer to page 59.
When connecting to a monaural TV
Use a stereo-mono conversion cord (not
supplied). Connect the LINE OUT (VIDEO)
jack on the player to the TV's video input
jack, and connect the LINE OUT L/R
(AUDIO) jacks to the TV's audio input jack.
C
COMPONENT
VIDEO IN
Y
(green)
P
B
(blue)
P
R
(red)
TV, projector or AV
amplifier (receiver)
(green) (blue) (red)
CD/DVD player
INPUT
S VIDEO
TV, projector or AV
B
amplifier (receiver)

Step 4: Playing a Disc

With the playback side facing down
A Turn on the TV.
B Press [/1 on the player.
C Switch the input selector on your
TV so that the signal from the
player appears on the TV screen.
D Press A on the player to open the
disc tray.
E Place the disc on the tray with the
playback side facing down.
F Press H.
The disc tray closes and the player begins
playing the disc.
A If you are connecting to a video input jack
Connect the yellow plug of the audio/video cord (supplied) to the yellow (video) jacks. You will
enjoy standard quality images.
Yellow (Video)
White (L)
Red (R)
Use the red and white plugs to connect to the audio input jacks (page 21). (Do this if you are
connecting to a TV only.)
B If you are connecting to an S VIDEO input jack
Connect an S VIDEO cord (not supplied). You will enjoy high quality images.
C If you are connecting to a monitor, projector, or AV amplifier (receiver)
having component video input jacks (Y, P
Connect the component via the COMPONENT VIDEO OUT jacks using a component video
cord (not supplied) or three video cords (not supplied) of the same kind and length. You will
enjoy accurate color reproduction and high quality images.
Green
Blue
Red
Notes
• Connect the player directly to the TV. If you pass the player signals via the VCR, you may not receive a
clear image on the TV screen.
CD/DVD player
• If your TV has only one available audio/video input jack, connect the VCR to the LINE IN jacks on the
player (DVP-NS415 only). In order to view the pictures from your VCR, the DVD player must be in
standby mode (page 16).
VCR
1-4
After Step 6
Depending on the disc, a menu may be
displayed on the TV screen. If so, select the
item you want from the menu and play the
DVD (page 32) or VIDEO CD disc (page 32).
To stop playing
Press x.
To remove the disc
Press A.
To turn off the player
Press [/1. The player enters standby mode
and the power indicator lights up in red.
17
Yellow (Video)
White (L)
Red (R)
, P )
B R
Green
Blue
Red
VCR
TV
Connect
directly
CD/DVD player
TV
19