NAD M15 HD Owner's Manual page 11

IDENTIFICATION OF CONTROLS
REAR PANEL
12 DIGITAL AUDIO IN (COAXIAL IN 1-4, OPTICAL IN 1-4)
• Connect to the corresponding optical or coaxial digital output of
sources such as CD or BD/DVD players, digital cable box, digital
tuners and other applicable components.
• Coaxial and Optical digital input association is configurable via the
Source Setup item of the Setup Menu OSD.
DIGITAL AUDIO OUT (COAXIAL OUT 1-2, OPTICAL OUT 1-2)
• Connect the optical or coaxial DIGITAL OUT to the corresponding
digital audio input of compatible devices such as receivers,
computer soundcard or other digital processors.
13 ETHERNET/LOCAL AREA NETWORK (LAN) PORT
LAN connection must be setup for wired connection to be established.
Set up a Wired Ethernet broadband router with broadband internet
connection. Your router or home network should have a built-in DHCP
server to consummate the connection.
• Using a standard straight-through Ethernet cable, connect one
end of the Ethernet cable to the LAN port of your wired Ethernet
broadband router and the other end to M15 HD's LAN port.
• This Ethernet connection has similar function as that of the RS232
connection. With your PC and the M15 HD on the same network,
it allows remote control of the M15 HD via compatible external
controllers.
• With your PC and M15 HD connected on the same network, the IP
address of your M15 HD can be obtained. Press together and then
release the front panel buttons [3 SOURCE] and [SOURCE 4] -
"System Info" is shown in the VFD and OSD. Toggle [3 SOURCE] or
[SOURCE 4] to individually show in the VFD the "System Info" details
which include the IP address.
• Refer to the NAD website for information about RS232 Protocol
documents and PC interface program.
NOTES
• NAD is not responsible for any malfunction of the M15 HD and/or the
internet connection due to communication errors or malfunctions
associated with your broadband internet connection or other connected
equipment. Contact your Internet Service Provider (ISP) for assistance or
the service bureau of your other equipment.
• Contact your ISP for policies, charges, content restrictions, service
limitations, bandwidth, repair and other related issues pertinent to
internet connectivity.
14 HDMI (HDMI IN 1-6, HDMI MONITOR OUT 1-2)
• Connect the sets of HDMI input to the HDMI OUT connectors of
source components such as DVD player, BD player or HDTV satellite/
cable box.
• Connect the HDMI MONITOR OUT 1 and/or HMDI MONITOR OUT
2 to compatible HDTV or projector with HDMI input. Both HDMI
output ports display simultaneously the same audio/video source.
WARNING
Before connecting and disconnecting any HDMI cables, both the M15
HD and the ancillary source must be powered OFF and unplugged from
the AC outlet. Failure to observe this practice may cause permanent
damage to all equipment connected via HDMI sockets.
10
15 UNSWITCHED AC OUTLET
• With M15 HD switched ON or at standby mode, mains power is
always available at this outlet.
• This outlet can be used for components that may require
continuous supply of AC mains; some tuners require uninterrupted
mains supply to retain preset memory, for instance.
• The total draw of all devices connected to this outlet must not
exceed 120 watts.
• Mains power at this outlet can be shut down by switching OFF the
M15 HD via the rear panel POWER switch.
16 AC MAINS INPUT
• The M15 HD comes supplied with a separate detachable mains
power cord. Before connecting the plug to the mains powers
source, connect firmly first the other end to M15 HD's AC Mains
input socket.
• Always disconnect the mains power plug from the mains power
source first, before disconnecting the cable from the M15 HD's AC
Mains input socket.
• Connect only to the prescribed AC outlet, i.e., 120V 60 Hz (for 120V
version models only) or 230V 50 Hz (for 230V version models only).
17 POWER
• Supply the AC mains power to the M15 HD.
• When the POWER switch is set to ON position, the M15 HD goes
to standby mode as shown by the amber status condition of the
Standby LED. Press the front panel Standby button or HTRM remote
control's [ON] button to switch ON the M15 HD from standby mode.
• If you intend not to use the M15 HD for long periods of time (such
as when on vacation), switch off the POWER switch.
• With POWER switched off, neither the front panel Standby button
nor HTRM remote control's [ON] button can activate the M15 HD.