Specifications - Tanita WB-8000RW Instruction Manual

3. Part Names & Specifications
Check Included Items
WB-8000RW AC adapter
Battery Box (Bottom)
Please use 4 AA alkaline
batteries.
USB Port Mode Selection Switch
USB ONLY
DC Jack Port
OFF
•••••••••••••••
Please use the included ON
••••••••••••••••
AC adapter.
<Specifications>
Model
Measurement System
Maximum Capacity / Minimum Graduation
Platform
Output Data Interface
Power Source
Power Consumption
Temperature Range of usage
2
Instruction (CD or Leaflet)
Warranty
Registration Card
LED Lamp
Changes color depending on what mode is selected.
Indicates status through color and blink pattern.
This LED lamp is green when the mode selection switch is set to
the "ON" position.
This LED lamp is blue when the mode selection switch is set to
the "USB ONLY" position.
LED off
• This LED is not lit when the mode selection switch is set to the
"OFF" position.
• If the LED is off, but the mode selection switch is not set to the
"OFF" position, please check the unit power.
Blinks once every 4 seconds
• Indicates WB-8000RW is in standby state.
* The unit will be in standby state after it is turned on.
Blinks once every 1 second
• Indicates the unit is ready to measure weight. Please step onto the
WB-8000RW.
Lit
• Indicates that data is being transmitted.
Blinks red 3 times after turning power on, when blinks red once
every 6 seconds
• Please replace the batteries.
Lit Red
• Error
* Automatically recovers.
Make sure to step onto the WB 8000RW only after it has beeped
twice or the Green indicator light is blinking.
The unit cannot accurately measure your weight if it detects
movement. Please stand on the platform keeping movement to a
minimum.
Reading cannot be obtained if the weight capacity is exceeded.
Weight capacity is 660lb (300kg).
USB bidirectional transmission mode. Use this when using a computer,
••••••••
etc. to control the unit. When this mode is selected, the LED will be blue.
OFF Mode : Power is off.
ON Mode : Both wireless transmission and USB output (output only) can
be used. When this mode is selected, the LED will be green.
WB-8000RW
Strain Gauge Load Cell
300kg / 0.1kg 660lb / 0.2lb
505 x 415 x 51 mm 19.9 x 16.1 x 2.0 inch
USB (B-type)
AC adapter (included) DC 9V 200mA
4 x LR6 - AA Alkaline Battery (Not included)
60mA
5°C to 35°C 41˚F to 95˚F
4. Using the WB 8000RW with D 8000 Remote Display
1. Provide Power
Provide power to both the D-8000 and the WB-8000RW. Each can be powered by either batteries or the included AC adapter.
* To ensure a stable and consistent power supply, whenever possible use the included AC adapter.
<D-8000 (Optional)>
When Using Batteries
(1) Loosen the display unit battery box screw, and slide the box out.
(2) Follow the markings on the case and insert 6 AA alkaline batteries.
Batteries
(3) Securely close the battery box and tighten the screw.
When Using the AC Adapter
(1) Insert the dedicated AC adapter into the DC jack port of the display unit.
(2) Plug the AC adapter into a wall outlet.
<WB-8000RW>
When Using Batteries
Battery Box
When Using the AC Adapter
(1) Insert the included AC adapter into the DC jack port on the left side of the weighing
unit.
(2) Plug the AC adapter into a wall outlet.
Note: •Be sure that the polarity of the batteries is set ploporly. If the batteries are
DC Jack port
DC Jack port
Open the battery cover on the bottom of the platform. Insert the
4 AA alkaline batteries as indicated.
incorrectly positioned, fluid may leak and damage floors. If you do not intend to
use this unit for long period of time, it is advisable to remove the batteries before
storage.
3