Download Print this page

Black & Decker VP650 Instruction Manual

7..2 volt multi-purpose saw
Hide thumbs

Advertisement

Quick Links

7 7
. .
2 2
V V
o o
l l
t t
M M
7 7
. .
2 2
V V
o o
l l
t t
M M

INSTRUCTION MANUAL

Catalog Number VP650
BEFORE RETURNING THIS PRODUCT
FOR ANY REASON PLEASE CALL
1-800-54-HOW-TO
IF YOU SHOULD EXPERIENCE A PROBLEM
WITH YOUR BLACK & DECKER PURCHASE,
CALL 1-800-54-HOW-TO (1-800-544-6986).
IN MOST CASES, A BLACK & DECKER REPRESENTATIVE
CAN RESOLVE YOUR PROBLEM OVER THE PHONE.
IF YOU HAVE A SUGGESTION OR COMMENT,
GIVE US A CALL. YOUR FEEDBACK IS VITAL
TO THE SUCCESS OF BLACK & DECKER'S QUALITY
IMPROVEMENT PROGRAM.
KEY INFORMATION YOU SHOULD KNOW:
•Charge batteries before first use.
•Charger may hum; batteries or charger may become warm while charging (batteries
and charger sold separately).
•Cutting shoe must be firmly against surface.
•Press lock-off switch before attempting to pull trigger.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
VEA EL ESPAÑOL EN LA CONTRAPORTADA.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE
GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL
PRODUCTO.
Cat. No. VP650
Form No. 380852-03
(OCT 99-1)
WARNING: IMPORTANT SAFETY WARNINGS
AND INSTRUCTIONS
TO REDUCE RISK OF INJURY:
• Before any use, be sure everyone using this tool reads and understands all safety instructions and
other information contained in this manual.
• Save these instructions and review frequently prior to use and in instructing others.
WARNING:
When using electric tools, basic safety precautions should always be followed
to reduce risk of fire, electric shock, and personal injury, including the
following.
READ ALL INSTRUCTIONS
GENERAL SAFETY WARNINGS AND INSTRUCTIONS FOR ALL TOOLS
• KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
• CONSIDER WORK AREA ENVIRONMENT. Don't expose power tools to rain. Don't use power tools in damp
or wet locations. Keep work area well lit. Do not use in presence of flammable liquids or gases. Motors in
these tools normally spark, and the sparks may ignite the fumes.
• GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded surfaces. For example; pipes,
radiators, ranges, refrigerator enclosures. Use extreme caution when drilling, driving, or cutting into walls,
floors, ceilings or other areas or wherever live electrical wires may be contacted, do not touch any metal
parts of the tool. Hold the tools only by the plastic handle to prevent electric shock.
• KEEP CHILDREN AWAY. Do not let children and visitors contact tool or extension cord. All children and
visitors should be kept away from work area.
• STORE IDLE TOOLS. When not in use, tools should be stored in dry, and high or locked-up place–out of
reach of children.
• DON'T FORCE TOOL. It will do the job better and safer at the rate for which it was intended.
• USE RIGHT TOOL. Don't force small tool or attachment to do the job of a heavy-duty tool. Don't use tool for
purposes not intended.
• DRESS PROPERLY. Do not wear loose clothing or jewelry. They can be caught in moving parts. Rubber gloves
and non-skid footwear are recommended when working outdoors. Wear protective hair covering to contain
long hair.
• USE SAFETY GLASSES AND OTHER SAFETY EQUIPMENT. Use safety goggles or safety glasses with side
shields, complying with applicable safety standards and, when needed, a face shield. Also use face or dust
mask if cutting operation is dusty. This applies to all persons in the work area. Also use a hard hat, hearing
protection, gloves, safety shoes and dust collection systems when specified or required.
• DON'T ABUSE CORD. Never carry tool by cord or yank it to disconnect from receptacle. Keep cord from
heat, oil, and sharp edges.
• SECURE WORK. Use clamps or a vise to hold work. It's safer than using your hand and it frees both hands to
operate tool.
• DON'T OVERREACH. Keep proper footing and balance at all times.
• MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer performance. Follow
instructions for lubricating and changing accessories. Inspect tool cords periodically and if damaged, have
repaired by authorized service facility. Inspect extension cords periodically and replace if damaged. Keep
handles dry, clean, and free from oil and grease.
• DISCONNECT TOOLS. Unplug the tool when not in use, when moving tool from place to place, before
servicing, and when changing accessories (such as blades, bits, cutters) or making adjustments.
• REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting
wrenches are removed from tool before turning it on.
• AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch is off when
plugging in.
• STAY ALERT. Watch what you are doing. Use common sense. Do not operate tool when you are tired or
otherwise impaired.
• CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be
carefully checked to determine that it will operate properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions
that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced
by an authorized service center. Do not use tool if switch does not turn it on and off.
• REPAIRS AND SERVICE. Repairs, maintenance and any adjustments not specified in this manual should be
performed by Black & Decker authorized service centers or other qualified service organizations, always
using identical replacement parts.
u u
l l
t t
i i
- -
P P
u u
r r
p p
o o
s s
e e
S S
a a
w w
u u
l l
t t
i i
- -
P P
u u
r r
p p
o o
s s
e e
S S
a a
w w
(544-6986)
Copyright © 1999 Black & Decker
• USE OF ACCESSORIES AND ATTACHMENTS. The use of any accessory or attachment not recommended for
R
use with the tool could be hazardous. Note: Refer to the accessory section of this manual for further details.
Important Safety Instructions (For Battery and Charger)
• Do not store or carry battery so that metal objects can contact exposed metal end shown in
Figure 1. For example, do not place battery in aprons, pockets, tool boxes, drawers etc. with
loose nails, screws, keys, etc. without battery cap. Battery could short circuit causing fire or burns
or damage to battery.
Battery caps are provided for use when carrying batteries or while battery is stored in a pocket,
tool box, etc. Remove cap before placing battery in charger or tool (see Figure 2).
• Never attempt to open the battery for any reason. If the housing of the battery breaks or cracks,
immediately discontinue use and do not recharge.
• Do not incinerate the batteries. They can explode in a fire. A small leakage of liquid from the
battery cells may occur under extreme usage, charging or temperature conditions. This does not
indicate a failure. However, if the outer seal is broken and this leakage gets on your skin:
a. Wash quickly with soap and water.
b. Neutralize with a mild acid such as lemon juice or vinegar.
c. If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10
minutes and seek immediate medical attention.
MEDICAL NOTE: The liquid is a 25-35% solution of potassium hydroxide.
• Charge batteries only with VersaPak battery charger.
• Do not use charger in wet or damp conditions. It is intended for indoor use only. Do not use near
sinks, tubs, or the like. Do not immerse in water.
• Do not use charger for any uses other than charging VersaPak batteries. Other batteries may
explode.
• Do not operate charger with damaged cord or plug — have them replaced immediately.
• Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in
any way; take it to a qualified Black & Decker service center.
• Do not disassemble charger; take it to a qualified Black & Decker service center when service or
repair is required. Incorrect reassembly may result in risk of electric shock or fire. There are no
consumer serviceable parts inside.
• For best results, do not charge batteries when they or air temperature is BELOW +40°F or ABOVE
+105°F.
• The charger is designed to operate on standard household electrical power. Do not attempt to use
it on any other voltage. Be sure your power supply agrees with the nameplate marking.
• Unplug charger when not in use.
• Do not abuse charger cord. To reduce the risk of damage to electric plug and cord, never carry
charger by cord or yank it to disconnect from receptacle. Keep charger cord from heat, oil, and
sharp edges.
• Use only charger supplied by the manufacturer to recharge.
Important Charging Notes
• While charging, the charger transformer may hum and batteries and charger become warm.
This is a normal condition and does not indicate a problem.
• If a battery does not charge properly— (1) Check current at receptacle by plugging in a lamp
or other appliance. (2) Check to see if receptacle is connected to a light switch which turns
power off when you turn out the lights. (3) Move charger and batteries to a surrounding air
temperature of +40°F to +105°F. (4) If the receptacle and temperature are OK, and you do not
Printed in U.S.A.
get proper charging, take or send the batteries and charger to your local Black & Decker
service center. See "Tools Electric" in yellow pages.
• The batteries should be recharged when they fail to produce sufficient power on jobs which
were easily done previously. DO NOT CONTINUE to use the tool with its batteries in a depleted
condition.
• Before using battery charger, read all instructions and cautionary markings on battery charger,
battery and product using battery.
CAUTION: To reduce the risk of injury, charge only nickel cadmium rechargeable batteries.
Other types of batteries may burst causing personal injury and damage.
Charging Procedure
Insert the metal end of the VersaPak battery into the charger. The indicator light will glow indi-
cating that charging is taking place and will remain on as long as the battery is in the charger.
Continuous charging is not a safety concern.
NOTE: VersaPak batteries are sent from the factory in an uncharged condition. Before
attempting to use them for the first time, they must be charged for 6 hours. Subsequent
charging for most fix up jobs will require 3-6 hours.
3
Bride de fixation de la lame
Porta seguetas
5
• KEEP HANDS AWAY from cutting areas. Never reach underneath the material for any reason.
• USE SHARP BLADES ONLY. Dull blades may break or cause the saw to swerve or stall under pressure.
CAUTION:
Some wood contains preservatives such as copper chromium arsenate (CCA) which can be
toxic. When cutting these materials extra care should be taken to avoid inhalation and minimize skin
contact.
CAUTION:
When sawing into walls, floors or wherever live electrical wires may be encountered, DO
NOT TOUCH ANY METAL PARTS OF THE TOOL! Hold the tool only by insulated grasping surfaces to
prevent electric shock if you saw into a live wire.
• Do not touch the workpiece or the blade immediately after operating the tool. They can become very hot.
• Always clamp the workpiece.
• Tighten blade clamp before each use.
WARNING:
defects or other reproductive harm. Use appropriate respiratory protection.
WARNING:
Always remove batteries from saw before any of the following operations.
BLADE INSTALLATION
Loosen the blade clamp screw by turning it counterclockwise with a screwdriver, (Fig. 3). Insert the saw blade
all the way, as shown, and tighten the screw. NOTE: Be sure to install the blade on the LEFT side of the clamp.
Do not force the blade into the right side of the clamp..
Metal End
Battery Cap
SAVE THESE INSTRUCTIONS
Shoe
Patin
Zapata
Blade Clamp
6
SAFETY WARNINGS AND INSTRUCTIONS: SAWS
Use of this tool can generate dust containing chemicals known to cause cancer, birth
ASSEMBLY/ ADJUSTMENT SET-UP
1
2
4
Release Buttons
Boutons de dégagement
Botones de liberación

Advertisement

loading

  Related Manuals for Black & Decker VP650

  Summary of Contents for Black & Decker VP650

  • Page 1: Instruction Manual

    Battery caps are provided for use when carrying batteries or while battery is stored in a pocket, • Catalog Number VP650 tool box, etc. Remove cap before placing battery in charger or tool (see Figure 2). BEFORE RETURNING THIS PRODUCT...
  • Page 2 OPERATING INSTRUCTIONS MESURES DE SÉCURITÉ POUR TOUS LES OUTILS REMOVING AND INSTALLING THE BATTERIES • BIEN DÉGAGER LA SURFACE DE TRAVAIL. Des surfaces et des établis encombrés peuvent être la cause de blessures. NOTE: VERSAPAK™ BATTERIES ARE NOT FULLY CHARGED AT THE FACTORY. •...
  • Page 3 le chargeur afin de minimiser les risques de dommages à la fiche et au cordon. Éloigner le cordon du adresses des centres de service Black & Decker se trouvent à la rubrique «Outils électriques» des Pages chargeur des sources de chaleur, des flaques d’huile et des arêtes tranchantes. Jaunes.
  • Page 4 b. Neutralice con un ácido débil como jugo de limón o vinagre. CORTE DE ÁRBOLES Utilice una segueta con dientes grandes para cortar o ramas de árboles. Sujete la zapata firmemente contra c. Si el líquido de la batería toca sus ojos, enjuáguelos con agua limpia por un mínimo de 10 minutos y la rama del árbol.