Page 1
NOTE: Please read all instructions carefully before using this LOUNGE ROCKER product Table of Contents GD-700 Safety Notice Hardware Pack Assembly Instruction Parts List Warranty Ordering Parts Model GD-700 Retain This Manual for Reference 100126 ® IMPEX INC. 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746...
ORDERING PARTS..................…. BEFORE YOU BEGIN ® Thank you for selecting the LOUNGE ROCKER GD-700 by IMPEX . For your safety and benefit, read this manual carefully before using the Hammock. As a manufacturer, we are committed to provide you complete customer satisfaction.
IMPORTANT SAFETY NOTICE Please read the entire manual before assembling or operating the equipment. In particular, note the following safety precautions to reduce the likelihood of injury. 1. Children must be supervised at all times and never left unattended with the unit. 2.
WARNING LABEL PLACEMENT The Warning Label shown here has been placed on the Stabilizer Frame. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown.
ASSEMBLY INSTRUCTION Tool Required for Assembling the Machine: Allen Wrench and Crossing Wrenches NOTE: It is strongly recommended that two or more people assemble this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Do not fasten Bolts until instructed to do so. B.) Slide the Front Cross Tube (#21) onto the front of the Right and Left Base (#8 &...
Page 7
Step 2 (See Diagram 2) A.) Do not fasten Bolt until all six M8 x 2” Allen Bolts (#2) are installed. B.) Place the Lounge Bed (#1) onto the six upright posts on the Right and Left Base (#8 & #22). Align the holes on the Lounge Bed Frame (#4) to the holes on the six upright posts.
Page 8
Step 3 (See Diagram 3) A.) Securely fasten all six Allen Bolts (#6) installed in Step-1. DIAGRAM 3...
Page 9
Step 4 (See Diagram 4) A.) Attach the Upright Stand (#25) to the bracket on the Rear Cross Tube (#28). Secure it with one M8 x 5/8” Hex Bolt (#16), one Ø 5/8” Washer (#18), and one M8 Aircraft Nut (#19). Note: Do not over tighten the Nut and Bolt.
Page 10
Step 5 (See Diagram 5) A.) Attach the Foot Rest Tube (#11) to the Foot Actuator (#12). Secure it with one M8 x 2” Allen Bolt (#2) and one Ø 7/8” x 5/16” Curved Washer (#3). B.) Slide the Foot Rest Support onto the Rocker Tube (#17). Use the Pop Pin (#13) to lock the Foot Actuator at selected hole to obtain the desired footrest position.
Page 11
Step 6 (See Diagram 6) A.) Attach the Rocker Tube (#17) to the bracket on Front Cross Tube (#21). Secure it with one M8 x 1 5/8” Hex Bolt (#16), one Ø 5/8” Washer (#18), and one M8 Aircraft Nut (#19). Note: Do not over tighten the Nut and Bolt.
Set up Lounge Rocker position 1. Neutral Position Turn the Upright Stand (#25) horizontally under the Middle Cross Tube (#29). Tuck the Rocker Tube (#17) under the Lounge Bed so the Rocker Tube could lean on the floor. 2. Rocking Position Turn the Upright Stand (#25) horizontally under the Middle Cross Tube (#29).
Page 13
Storage Lift up the front of Lounge vertically for space saving storage.
Parts list KEY NO. DESCRIPTION Q’ty Lounge Bed M8 x 2” Allen Bolt Ø 7/8” x 5/16 Curved Washer Lounge Bed Frame Ø 1 ¼” End Cap M10 x 2” Allen Bolt Ø 1” x 3/8” Curved Washer Right Base Ø...
® IMPEX INC. LIMITED WARRANTY ® IMPEX INC ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of 2 YEARS from the date of purchase. This warranty extends only to the original purchaser.