Page 1
To ensure you have the latest revision of the manual or to obtain the illustrated parts catalog, please visit the Bunn-O-Matic website, at www.bunn.com. This is absolutely FREE, and the quickest way to obtain the latest catalog and manual updates. Contact Bunn-O-Matic Corporation at 1-800-263- 2256 to obtain a paper copy of the required Illustrated Parts Catalog mailed via Canada Post.
Page 2
AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND. In no event shall Bunn be liable for any other damage or loss, including, but not limited to, lost profits, lost sales, loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute equipment, facilities or services, or any other special, incidental, consequential or punitive damages.
ELECTRICAL REQUIREMENTS WARNING - If the power cord is ever damaged, it must be replaced by the manufacturer or its service agent with a special cord available from the manufacturer or its service agent in order to avoid a hazard. Refer to Data Plate on the Brewer, and local/national electrical codes to determine circuit requirements.
NOTE - Bunn-O-Matic recommends 3⁄8" copper tubing for all installations from the 1⁄2" water supply line. A tight coil of copper tubing in the water line will facilitate moving the brewer to clean the counter top. Bunn-O-Matic does not recommend the use of a saddle valve to install the brewer. The size and shape of the hole made in the supply line by this type of device may restrict water flow.
OPERATING CONTROLS READY TO BREW ENABLE ENABLE ON / OFF ON / OFF WATER TEMP: 200° BREW BREW LARGE LARGE BREW BREW SMALL SMALL A. MAIN ON/OFF SWITCH This switch, located under the brewer in front of the right rear leg, turns power on and off to all components in the brewer.
7. Water volumes and flow settings have been preset at the factory. Refer to adjustments for the Set Brew Volumes or Calibrate Flow section of the Programming Manual on the Bunn-O-Matic website, at www.bunn. com should the volume need to be increased or decreased.
1. Begin each brew cycle with a clean empty brew funnel. edge of filter 2. Insert a BUNN filter into the funnel. NOTE: The funnels are equipped with 4 wire loops that can be folded over top edge of filter if desired, to prevent filter from folding in during the brew cycle.
Page 9
1. The use of a damp cloth rinsed in any mild, nonabrasive, liquid detergent is recommended for cleaning all surfaces on Bunn-O-Matic equipment. Do NOT clean this equipment with a water jet device. 2. Check and clean each sprayhead. The sprayhead holes must always remain open.
Page 10
à nouveau étalonné être doive l’appareil peut programmés. débits avec buse d’écoulement débit comparer pour www.bunn.com, l’adresse à O-Matic, Bunn- site seulement) anglais 41344.0000 programmation manuel Consultez main. à serrage qu’un nécessite Elle fixez-la. buse Remontez minéraux.
Page 11
Versez d’infusion. cycle pendant retenir pour filtre rebord rabattus être choix, peuvent, métallique boucles munis sont entonnoirs NOTE l’entonnoir. dans BUNN filtre Insérez filtre rebord vide. propre d’infusion entonnoir avec infusion chaque Commencez Rabattre CAFÉ PRÉPARATION PRINCIPAL. l'ÉCRAN à revenir...
Page 12
Entre – D’INFUSION L’EAU TEMPÉRATURE TEMPÉRATURE CHOIX café. Préparation section instructions conformément utiliser à prêt maintenant L’infuseur augmenter. réduire pour www.bunn.com, l'adresse à Bunn-O-Matic, site accessible 41344.0000 programmation manuel Flow) Calibrate Settings (Brew débits calibrage d’infusion volumes réglage section Consultez usine.
Page 13
Page 080108 40119 programmation. mode l’infuseur programmer à servent dissimulées touches FONCTIONS D’ÉCRAN INTERRUPTEURS programmation. effectuer d’en permettent l’infuseur fonctions différentes affiche écran FONCTIONS ÉCRAN côtés. deux portions régler pour programmation durant aussi sert touche Cette sélectionnée. portion indique voyant cours.
Page 14
étrier à robinet-vanne d’utiliser recommande Bunn-O-Matic l’infuseur. repose laquelle surface nettoyer pour l’infuseur déplacer permet couronnes cuivre tuyau d’un d’alimentation conduite L’installation eau. d’alimentation 1⁄2 conduite à...
Page 15
Page 080108 40119 initial. Réglage pour prêt distributeur raccordée, été tuyauterie courant. prise débranché distributeur assurez-vous suite, raccordée être doit tuyauterie commencer. avant jonction bloc tension vérifiez courant prise à l’infuseur Branchez jonction. bloc accéder pour avant panneau Retirez d’alimentation. cordon spécifiée raccordement...