Lenovo 3057 Maintenance Manual
  1. Manuals
  2. Brands
  3. Lenovo Manuals
  4. Server
  5. ThinkServer 3057
  6. Maintenance manual
Lenovo 3057 Maintenance Manual

Lenovo 3057 Maintenance Manual

Machine types: 3057, 3059, 3061, 3064, 3065, 3069, 3070, 3071, and 4306
Hide thumbs Also See for 3057:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Manual
ThinkServer RD430
Hardware Maintenance Manual
Machine Types: 3057, 3059, 3061, 3064, 3065, 3069, 3070, 3071,
and 4306

Advertisement

Table of Contents
loading

Related Manuals for Lenovo 3057

Summary of Contents for Lenovo 3057

  • Page 1 ThinkServer RD430 Hardware Maintenance Manual Machine Types: 3057, 3059, 3061, 3064, 3065, 3069, 3070, 3071, and 4306...
  • Page 2 • Appendix A “Notices” on page 201 Second Edition (December 2012) © Copyright Lenovo 2012. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.

  • Page 3: Table Of Contents

    Remote management software ..About RAID ....Lenovo Rack Planner ..Configuring RAID using the ThinkServer ThinkServer Smart Grid Technology .
  • Page 4 ThinkServer Web site ..Installing or replacing the microprocessor . . Lenovo Support Web site..Installing or replacing the optical drive . . .

  • Page 5: Safety Information

    제품을 사용하기 전에 제품과 함께 제공되는 문서 DVD의 다국어 안전 지침을 주의 깊게 읽어보십시오. Voordat u het product gebruikt, moet u ervoor zorgen dat u de meertalige veiligheidsinstructies op de documentatie-dvd van het product hebt gelezen en begrijpt. © Copyright Lenovo 2012...
  • Page 6 Przed skorzystaniem z produktu należy zapoznać się z wielojęzycznymi instrukcjami bezpieczeństwa znajdującymi się na płycie DVD z dokumentacją dostarczoną wraz z produktem. Antes de utilizar o produto, leia atentamente as instruções de segurança multilingues que constam no DVD de documentação fornecido com o produto. Înainte de a utiliza produsul, asiguraţi-vă...
  • Page 7 The battery contains lithium and can explode if not properly used, handled, or disposed of. Do not: • Throw or immerse into water • Heat to more than 100°C (212°F) • Repair or disassemble Dispose of the battery as required by local ordinances or regulations. © Copyright Lenovo 2012...
  • Page 8 Statement 3 CAUTION: When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are installed, note the following: • Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device. •...
  • Page 9 Statement 9 CAUTION: Disconnect the hot-swap fan cables before removing the fan from the device to protect against personal injury. Statement 10 CAUTION: The following label indicates a sharp-edge hazard. © Copyright Lenovo 2012...
  • Page 10 Statement 11 CAUTION: The following label indicates a potential heat hazard. Statement 12 DANGER Overloading a branch circuit is a potential fire hazard and a shock hazard under certain conditions. To avoid these hazards, ensure that your system electrical requirements do not exceed branch current ratings at the installation site.
  • Page 11 This product contains a Class 1M laser. Do not view directly with optical instruments. Statement 18 CAUTION: Do not place any object on top of rack-mounted products. Statement 19 CAUTION: Hazardous moving parts. Keep fingers and other body parts away. © Copyright Lenovo 2012...

  • Page 12: Safety Inspection Guide

    Statement 20 CAUTION: A lithium ion battery is provided. To avoid possible explosion, do not burn the battery. Replace the battery only with the Lenovo-approved part. Recycle or discard the battery as instructed by local regulations. Safety inspection guide The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service technicians from injury.

  • Page 13: Grounding Requirements

    Grounding requirements Electrical grounding of the server is required for operator safety and correct system function. Proper grounding of the electrical outlet can be verified by a certified electrician. © Copyright Lenovo 2012...
  • Page 14 ThinkServer RD430 Hardware Maintenance Manual...

  • Page 15: Chapter 1. General Information

    • For the most up-to-date information about your server, go to: http://www.lenovo.com/thinkserver • Lenovo maintains pages on the World Wide Web, where you can get the latest technical information and download documentation or device drivers and updates. To access the Lenovo Support Web site, go to: http://www.lenovo.com/support...
  • Page 16 DVD. Note: Lenovo maintains pages on the World Wide Web, where you can get the latest technical information and download documentation or device drivers and updates. Some information in the documents on the documentation DVD might change without notice after the first release of the DVD.
  • Page 17 This document provides information about component locations, replacement procedures for major Field Replaceable Units (FRUs), and troubleshooting and diagnostics. This document is updated frequently, and the most up-to-date version is always available in English on the Lenovo Web site at: http://www.lenovo.com/ThinkServerUserGuides...
  • Page 18 ThinkServer RD430 Hardware Maintenance Manual...

  • Page 19: Chapter 2. Server Setup Road Map

    ThinkServer EasyStartup program. 10. Check for firmware updates. See “Updating the firmware” on page 80. 11. Install management applications and any other applications. Refer to the documentation that comes with the applications that you want to install. © Copyright Lenovo 2012...
  • Page 20 ThinkServer RD430 Hardware Maintenance Manual...

  • Page 21: Chapter 3. Product Overview

    DVD, and software media. Note: Depending on the model, your server might look slightly different from the following illustration. Figure 1. Server package Server Material box, including power cords, printed documentation, a documentation DVD, and software media Rail kit © Copyright Lenovo 2012...

  • Page 22: Features

    (internal cache size varies by model) For a list of the ThinkServer microprocessor options, go to: http://www.lenovo.com/thinkserver Memory Your server has 12 memory slots. For more information, see “Memory module installation rules” on page 97.
  • Page 23 – Hot-swap redundant power supplies to protect against significant interruption to the operation of the system when a power supply fails (for server models that come with one power supply, you can purchase a hot-swap redundant power supply option from Lenovo and install it into your server as the second power supply for redundancy) –...
  • Page 24 For more information, refer to the ThinkServer Management Module User Guide, which is available for download at: http://www.lenovo.com/ThinkServerUserGuides – Hot-swap feature Your server supports hot-swap hard disk drives, hot-swap system fans, and hot-swap redundant power supplies. With the hot-swap feature, you can install, remove, or replace a hot-swap device without turning off the server.

  • Page 25: Specifications

    TMM Premium from Lenovo and install it on the TMM Premium connector (also known as iKVM connector) on the system board of your server to enable the iKVM function and activate the advanced system management features. For more information about advanced system management, refer to the ThinkServer Management Module User Guide, which is available for download at: http://www.lenovo.com/ThinkServerUserGuides...

  • Page 26: Software

    The BIOS and TMM (also known as BMC) firmware keeps updating after the shipment of the server. Lenovo maintains pages on the Support Web site and provides the BIOS and TMM update utilities with instructions for download to help you update the BIOS and TMM firmware if needed. For more information, see “Updating or recovering the BIOS”...

  • Page 27: Thinkserver Smart Grid Technology

    To download the Lenovo Rack Planner program, go to http://www.lenovo.com/drivers and follow the instructions on the Web page. For detailed information about using the Lenovo Rack Planner program, refer to the help system for the program. ThinkServer Smart Grid Technology...
  • Page 28 The machine type, model, and serial number label is attached on the pull-out information card in the following server models: • Server models with eight 3.5-inch hard disk drive bays • Server models with 2.5-inch hard disk drive bays The pull-out information card is a small plastic tab and can be slid out of the front of the chassis. Figure 2.

  • Page 29: Front View Of The Server

    For server models with 12 3.5-inch hard disk drive bays, the machine type, model, and serial number label is attached on the left side of the server. Figure 4. Label on server models with 12 3.5-inch hard disk drive bays Front view of the server This topic provides information to help you locate the parts on the front of the server.
  • Page 30 Front view of server models with eight 3.5-inch hard disk drive bays The following illustration shows the front view of server models with eight 3.5-inch hard disk drive bays. Figure 5. Front view of server models with eight 3.5-inch hard disk drive bays 3.5-inch hard disk drive area Diagnostic panel (varies by model) Rack handle (left)
  • Page 31 Pull-out information card The machine type, model, and serial number label of the server is attached on the pull-out information card. See “Machine type, model, and serial number label” on page 13. Front panel For detailed information about the controls, connectors, and status LEDs on the front panel, see “Front panel”...
  • Page 32 3.5-inch hard disk drive area The EMI integrity and cooling of the server are protected by having all drive bays covered or occupied. The number of the installed hard disk drives in your server varies by model. The vacant hard disk drive bays are occupied by dummy hard disk drive trays.
  • Page 33 Power status LED Color Description The server is on. Green None The server is off. Blinking Green The server is in ACPI S1 mode, which also is known as Power On Suspend (POS) mode. In this mode, the microprocessors are not working while other hardware devices are still working.
  • Page 34 Front view of server models with 2.5-inch hard disk drive bays The following illustration shows the front view of server models with 2.5-inch hard disk drive bays. Figure 9. Front view of server models with 2.5-inch hard disk drive bays 2.5-inch hard disk drive area (right cage) Rack handle (left) 2.5-inch hard disk drive area (middle cage)

  • Page 35: Front Panel

    Slim optical drive Some server models come with a slim SATA optical drive. Rack handle (left) Rack handle (right) If your server is installed in a rack cabinet, you can use the rack handles to help you slide the server out of the rack cabinet;...
  • Page 36 Power switch with power status LED You can press the power switch to turn on the server when you finish setting up the server. You also can hold the power switch for several seconds to turn off the server if you cannot turn off the server from the operating system.

  • Page 37: Diagnostic Module

    Front USB connectors Used to attach a USB-compatible device, such as a USB keyboard, mouse, scanner, or printer. If you have more than six USB devices, you can purchase a USB hub, which you can use to connect additional USB devices. VGA DB-15 connector Used to attach a VGA-compatible video device, such as a VGA monitor.
  • Page 38 Power supply error LED When the power supply error LED is lit in amber, it indicates that there is a power supply problem. To identify the failing power supply, check the status LED near the power cord connector on the redundant power supply.
  • Page 39 System fan error LEDs When a system fan error LED is lit in amber, it indicates that the corresponding system fan is operating slowly or has failed. The following illustration shows the system fans and their numbers. Notes: • Depending on the model, your server might look slightly different from the illustration. •...

  • Page 40: Rear View Of The Server

    CPU1 DIMM status LEDs CPU2 DIMM status LEDs When a DIMM status LED is lit in amber, it indicates that the corresponding memory module is overheated. The following illustration shows the memory modules and their numbers. Figure 15. DIMM status LEDs and DIMMs Ambient temperature limit LED When this LED is lit in amber, it indicates that the ambient temperature is below 7°C (44.6°F) or over 40°C (104°F), which is not proper for server operation.
  • Page 41 You can purchase a hot-swap redundant power supply option from Lenovo and install the power supply to provide power redundancy without turning off the server. On each hot-swap redundant power supply, there is a status LED near the power cord connector. When the LED is lit in green, it indicates that the hot-swap redundant power supply is working correctly.
  • Page 42 • If a ThinkServer Host Bus Adapter is available, refer to its user guide for detailed information. The user guide is available for download at: http://www.lenovo.com/drivers PCI Express Physical link Negotiable link width...
  • Page 43 1 with a black lower slot. • If a ThinkServer Host Bus Adapter is available, refer to its user guide for detailed information. The user guide is available for download at: http://www.lenovo.com/drivers PCI Express Physical link...
  • Page 44 5 8 9 Ethernet connectors (RJ-45) Used to attach an Ethernet cable for a LAN. Each Ethernet connector has two status LEDs to help you identify the Ethernet connectivity, activity, and connection speed. Notes: • The Ethernet connector 0 (callout ) marked with “MGMT”...

  • Page 45: Server Components

    ID LED When you press the ID button on the front of the server, the ID LEDs on both the front and rear of the server are lit to help you locate the server among other servers. You also can turn on the ID LEDs using a remote management program for server presence detection.
  • Page 46 Components of server models with eight 3.5-inch hard disk drive bays Figure 20. Components of server models with eight 3.5-inch hard disk drive bays Cooling shroud Pull-out information card Power supply cooling shroud Rack handle (left) Riser card assembly 2 Front panel board One or two hot-swap redundant power supplies Backplane for server models with eight 3.5-inch hard disk...
  • Page 47 Components of server models with 12 3.5-inch hard disk drive bays Figure 21. Components of server models with 12 3.5-inch hard disk drive bays Cooling shroud Backplane for server models with 12 3.5-inch hard disk drive bays Power supply cooling shroud System fans (4) Riser card assembly 2 CPU1 DIMMs (vary by model)
  • Page 48 Components of server models with 2.5-inch hard disk drive bays Figure 22. Components of server models with 2.5-inch hard disk drive bays Cooling shroud Slim optical drive (available in some models) Power supply cooling shroud Diagnostic module (varies by model) Riser card assembly 2 Rack handle (left) One or two hot-swap redundant power supplies...
  • Page 49 FRU information, such as FRU part numbers and supported server models, go to: http:/www.lenovo.com/serviceparts-lookup Notes: • Before servicing a Lenovo product, ensure that you read and understand “Safety information” on page iii. • Use only parts provided by Lenovo. Self-service...

  • Page 50: Hot-Swap Hard Disk Drive Status Leds

    Hot-swap hard disk drive status LEDs Each hot-swap hard disk drive has two status LEDs on the front. Figure 23. 3.5-inch hot-swap hard disk drive status LEDs Figure 24. 2.5-inch hot-swap hard disk drive status LEDs Hard disk drive activity LED Hard disk drive RAID status LED Description The hard disk drive has failed or is...

  • Page 51: Raid Card

    Some server models come with a RAID card to provide advanced SATA/SAS hardware RAID functions. You also can purchase a supported RAID card from Lenovo and install it into the server. See “Installing or removing the RAID card” on page 103.
  • Page 52 ThinkServer RAID 700 Adapter (also known as ThinkServer 9260-8i SAS RAID Adapter) The following illustration shows the connectors on the ThinkServer RAID 700 Adapter. Figure 26. ThinkServer RAID 700 Adapter Ports 7-4 Board-to-board connector Ports 3-0 Ports 7-4 Used to connect a mini-SAS signal cable. See “Mini-SAS to mini-SAS signal cable connections” on page 44. Ports 3-0 Used to connect a mini-SAS signal cable.

  • Page 53: Expander Card

    ThinkServer RAID 710 Adapter (also known as 9270CV-8i RAID adapter) The following illustration shows the connectors on the ThinkServer RAID 710 Adapter. Figure 27. ThinkServer RAID 710 Adapter Port 1 ThinkServer RAID Super Capacitor Module connector Port 2 Port 1 Used to connect a mini-SAS signal cable.

  • Page 54: Hot-Swap Hard Disk Drive Backplane

    The following illustration shows the connectors on the expander card. Each connector on the expander card is used to connect a mini-SAS to mini-SAS signal cable. For detailed information, see “Mini-SAS to mini-SAS signal cable connections” on page 44. Figure 28. Expander card Connector 1 Connector 4 Connector 2...
  • Page 55 The following illustrations show the connectors on the backplane for server models with eight 3.5-inch hard disk drive bays. Figure 29. Front view of the backplane for server models with eight 3.5-inch hard disk drive bays Slot 0 for a 3.5-inch hard disk drive Slot 7 for a 3.5-inch hard disk drive Slot 2 for a 3.5-inch hard disk drive Slot 5 for a 3.5-inch hard disk drive...
  • Page 56 Backplane for server models with 12 3.5-inch hard disk drive bays This topic provides information to help you locate the connectors on the backplane for server models with 12 3.5-inch hard disk drive bays. The following illustrations show the connectors on the backplane for server models with 12 3.5-inch hard disk drive bays.
  • Page 57 Mini-SAS ports 4-7 Used to connect the mini-SAS connector on one end of a mini-SAS to mini-SAS signal cable to support the hard disk drive 4 to hard disk drive 7. Mini-SAS ports 0-3 Used to connect the mini-SAS connector on one end of a mini-SAS to mini-SAS signal cable to support the hard disk drive 0 to hard disk drive 3.

  • Page 58: Mini-Sas To Mini-Sas Signal Cable Connections

    Figure 34. Rear view of the backplane for server models with 2.5-inch hard disk drive bays 8-pin power connector Mini-SAS ports 0-3 Mini-SAS ports 4-7 Optical drive power connector 8-pin power connector Used to connect a power cable to provide power to the backplane. Mini-SAS ports 4-7 Used to connect the mini-SAS connector on one end of a mini-SAS to mini-SAS signal cable to support the hard disk drive 4 to hard disk drive 7;...
  • Page 59 Note: The option kit for a RAID card is designed for different types of servers and might contain additional cables that are not required for your server. To connect cables from the RAID card to the backplane, do one of the following depending on the type of your RAID card: •...
  • Page 60 Use the following instructions to connect cables from the RAID card to the expander card first: • If you are using a ThinkServer RAID 500 Adapter, do the following: 1. Use a mini-SAS to mini-SAS signal cable and connect the mini-SAS connector on one end of the cable to the port 0 on the ThinkServer RAID 500 Adapter.
  • Page 61 Use the following instructions to connect cables from the expander card to the backplanes for 2.5-inch hard disk drives: 1. For hard disk drive 0 to hard disk drive 3, use a mini-SAS to mini-SAS signal cable and connect the mini-SAS connector on one end of the cable to the connector 3 on the expander card.
  • Page 62 Use the following instructions to connect cables from the expander card to the backplane for 12 3.5-inch hard disk drives: 1. For hard disk drive 0 to hard disk drive 3, use a mini-SAS to mini-SAS signal cable and connect the mini-SAS connector on one end of the cable to the connector 3 on the expander card.

  • Page 63: System Board Components

    connect the mini-SAS connector on the other end of the cable to the mini-SAS ports 0-3 on the backplane. 2. If your server has more than four hard disk drives installed, for hard disk drive 4 to hard disk drive 7, use another mini-SAS to mini-SAS signal cable and connect the mini-SAS connector on one end of the cable to the SAS connector 4-7 on the system board.
  • Page 64 SAS connector 4-7 Backplane power connector 2 Microprocessor socket 2 SAS connector 0-3 System board battery System fan 5 connector Platform Controller Hub (PCH) Memory slots (6) Internal USB Type A connector 2 System fan 4 connector TMM Premium connector Microprocessor socket 1 Internal USB Type A connector 1 System fan 2 connector...
  • Page 65 Platform Controller Hub (PCH) This chip supports and provides many features. It serves as a PCH, which provides the data buffering and interface arbitration required to ensure that system interfaces operate efficiently and provides the bandwidth necessary for the system to achieve peak performance. Internal USB Type A connector 2 Internal USB Type A connector 1 Used to connect a device that uses a USB Type A connector.

  • Page 66: System Board Jumpers And Switches

    Backplane power connector 1 Backplane power connector 2 Used to connect the power cables from the backplane. 24 26 28 30 System fan connectors There are four hot-swap system fans and two dummy system fans installed in the system fan cage in your server.
  • Page 67 The following illustration shows the status of the jumpers and switches on the system board of your server. You can configure, recover, enable, or disable some specific features of the system board by setting the jumpers and switches. Figure 40. System board jumpers and switches Clear CMOS (Complementary Metal Oxide Semiconductor) jumper TMM Enable/Disable jumper (also known as BMC Enable/Disable jumper) System board switches...
  • Page 68 2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat, clean, and static-protective surface. See the Rack Installation Instructions that comes with the server. 3. Remove the server cover. See “Removing the server cover” on page 85. 4.
  • Page 69 System board switches There are four switches on the system board of your server. Figure 41. System board switches BIOS recovery switch Management Engine (ME) in force update switch Clear password switch Reserved for the manufacturer BIOS recovery switch Used to recover the BIOS if the power to your server is interrupted while the BIOS is being updated and your server cannot start correctly.

  • Page 70: System Board Leds

    1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat, clean, and static-protective surface.
  • Page 71 To solve the problem, you might need to reinstall or replace the system fan. See “Replacing a system fan” on page 174. If it is a system board problem, contact the Lenovo Customer Support Center.
  • Page 72 ThinkServer RD430 Hardware Maintenance Manual...

  • Page 73: Chapter 4. Turning On And Turning Off The Server

    • You also can use the related TMM feature to remotely turn off the server through the management LAN. For more information about the TMM, refer to the ThinkServer Management Module User Guide, which is available for download at: http://www.lenovo.com/ThinkServerUserGuides © Copyright Lenovo 2012...
  • Page 74 • The server might be turned off as an automatic response to a critical system failure. Notes: • When you turn off the server and leave it connected to an ac power source, the server also can respond to a remote request to turn on the server. To remove all power from the server, you must disconnect the server from the ac power source.

  • Page 75: Chapter 5. Configuring The Server

    • “Updating the firmware” on page 80 • “Using the Lenovo ThinkServer EasyManage program” on page 81 Using the Setup Utility program This topic provides information about using the Setup Utility program. The Setup Utility program is part of the server firmware. You can use the Setup Utility program to view and change the configuration settings of your server, regardless of which operating system you are using.

  • Page 76: Setup Utility Program Interface

    “Save & Exit menu” on page 64 Lenovo provides the BIOS update utility on the Lenovo Support Web site. You can download the BIOS update utility to update the BIOS if the newer BIOS version specifically solves a problem you have. See “Updating or recovering the BIOS”...
  • Page 77 Notes: • Enabled means that the function is configured. • Disabled means that the function is not configured. The Advanced menu contains the following submenus. For more information, enter the corresponding submenu and refer to the instructions on the screen. •...

  • Page 78: Setting The System Date And Time

    The Server Management menu contains the following submenus. For more information, enter the corresponding submenu and refer to the instructions on the screen. • Erase SEL: Erase system event log (SEL). • System Information: View basic information about your server. •...

  • Page 79: Using Passwords

    3. Use the Tab key to switch between data elements and type the numbers from the keyboard to set the system date and time. 4. Press F10 to save settings and exit the Setup Utility program. Using passwords By using the Setup Utility program, you can set a password to prevent unauthorized access to your server. You do not have to set a password to use your server.

  • Page 80: Selecting A Startup Device

    TPM function is only available when there is a TPM installed in your server. See “Installing the TPM” on page 128. You can purchase a TPM from Lenovo. After installing a TPM, you need to check if the TPM function is enabled in the Setup Utility program.

  • Page 81: Setting The Mode Of The Ethernet Connector 0

    Setup Utility program” on page 61. The TMM firmware provides remote management features. Lenovo might make changes and enhancements to the BIOS and TMM firmware. When updates are released, they are available for download on the Lenovo Web site at http://www.lenovo.com/drivers. You can update the server firmware by downloading an update package and following the instructions on the Web page.

  • Page 82: Recovering From A Bios Update Failure

    BIOS for an easier reconfiguration in the new BIOS version. To update (flash) the BIOS, do the following: 1. Go to http://www.lenovo.com/drivers and follow the instructions on the Web page to locate the BIOS update package. 2. Download the BIOS update package and the installation instructions in a TXT file.

  • Page 83: Using The Thinkserver Easystartup Program

    (bootable) ThinkServer EasyStartup DVD. The user guide for the program also is on the DVD and can be accessed directly from the program interface. If you do not have a ThinkServer EasyStartup DVD, you also can download an ISO image from the Lenovo Support Web site and make a disc by yourself.

  • Page 84: Features Of The Thinkserver Easystartup Program

    • Ability to install the operating system and device drivers in an unattended mode to save time • Ability to create a reuseable response file that can be used with similarly configured Lenovo servers to make future installations even faster Starting the ThinkServer EasyStartup program This topic provides instructions on how to start the ThinkServer EasyStartup program.

  • Page 85: Using The Thinkserver Easystartup Program On A Windows Operating System

    Note: The most up-to-date device drivers for various server models are always available for download on the Lenovo Support Web site at: http://www.lenovo.com/drivers • About This menu provides the version information and legal notices.

  • Page 86: Configuring Raid

    DVD into an internal or external optical drive. The DVD starts automatically in most environments. If the DVD fails to start, open the launch.exe file located in the root directory of the DVD. Notes: • You should read and accept the Lenovo License Agreement when prompted. ® • On the Microsoft Windows Server...
  • Page 87 RAID drive groups also improve data storage reliability and fault tolerance compared with single-drive storage systems. Data loss resulting from a drive failure can be prevented by reconstructing missing data from the remaining drives. The following list describes some of the most commonly used RAID levels: •...

  • Page 88: Configuring Raid Using The Thinkserver Easystartup Program

    • Supports hot-spare drives • Creates a RAID response file that can be used to configure RAID controllers on similarly configured Lenovo servers See “Using the ThinkServer EasyStartup program” on page 69 and view the user guide from the main interface of the program.
  • Page 89 This status indicates that more than one hard disk drive in the RAID array cannot be synchronized or have failed. You need to replace the failing hard disk drives and rebuild the data. See “Installing or replacing a hot-swap hard disk drive” on page 150 and “Rebuilding a physical drive” on page 78. •...
  • Page 90 The following table shows the various menus and items in the LSI Software RAID Configuration Utility program. On each menu, press the Enter key to show selectable options and select a desired option by using up and down arrow keys or type desired values from the keyboard directly. Table 1.

  • Page 91: Initializing A Virtual Drive

    • If you want to delete the existing RAID array, exit the program and back up all your data on the hard disk drives. After backing up all your data, enter the program main interface and select Clear Configuration. Select Yes when prompted and follow the instructions on the screen. Attention: Deleting an existing RAID array erases all data on the array.

  • Page 92: Running A Consistency Check

    • If you want to set a hot-spare drive right after the configuration, select Objects ➙ Physical Drive from the program main interface. Then, select the hard disk drive that you want to set as a hot-spare drive and press Enter. A submenu is displayed. Select Make Hot Spare from the submenu and then select Yes when prompted to set the hard disk drive as a hot-spare drive.

  • Page 93: Configuring The Advanced Sata/Sas Hardware Raid

    • “MegaRAID Storage Manager Window and Menus” • “Monitoring System Events and Storage Devices” • “Maintaining and Managing Storage Configurations” The MegaRAID SAS Software User Guide also is available on the Lenovo Web site at: http://www.lenovo.com/ThinkServerUserGuides Configuring the advanced SATA/SAS hardware RAID Before configuring RAID for your server, observe the following precautions: •...

  • Page 94: Configuring The Ethernet Controllers

    Some server models come with a RAID card to provide advanced SATA/SAS hardware RAID functions. You also can purchase a supported RAID card from Lenovo and install it into the server. See “RAID card” on page 37. The RAID card provides the WebBIOS Configuration Utility program to help you configure RAID independently of the operating system.

  • Page 95: Using The Lenovo Thinkserver Easymanage Program

    The Lenovo ThinkServer EasyManage program enables enterprise users to remotely control and monitor multiple Lenovo servers within a LAN. The program provides an interface to display all severs being managed, which enables the administrator to conveniently search for, monitor, and manage servers.
  • Page 96 ThinkServer RD430 Hardware Maintenance Manual...

  • Page 97: Chapter 6. Installing, Removing, Or Replacing Hardware

    • Before using the product, ensure that you read and understand the multilingual safety instructions and the Lenovo Limited Warranty (LLW) on the documentation DVD that comes with the product. Reading and understanding the safety instructions reduces the risk of personal injury and damage to your product.

  • Page 98: Handling Static-Sensitive Devices

    • Have a small flat-blade screwdriver available. • You do not have to turn off the server to install or replace a hot-swap redundant power supply, hot-swap hard disk drives, or hot-plug USB devices. However, you must turn off the server before performing any steps that involve installing, removing, or replacing adapter cables or non-hot-swap devices or components.

  • Page 99: System Reliability Guidelines

    – Attach the ESD ground clip to any frame ground, ground braid, or green-wire ground. – When working on a double-insulated or battery-operated system, use an ESD common ground or reference point. You can use coax or connector-outside shells on these systems. –...
  • Page 100 Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. Note: Depending on the model, your server might look slightly different from the illustrations in this topic. To remove the server cover, do the following: 1.

  • Page 101: Removing And Reinstalling The Front Bezel

    6. Fully open the cover latch and slide the server cover to the rear until it is disengaged from the chassis. Then, lift the server cover off the chassis and set it aside. Note: It is recommended that you wait three to five minutes to let the server cool before removing the server cover.

  • Page 102: Installing, Removing, Or Replacing Hardware

    1. Remove the three screws that secure the front bezel and then pivot the front bezel outward to remove it from the chassis. Figure 45. Removing the front bezel 2. To reinstall the front bezel, align the tabs on the bottom edge of the front bezel with the corresponding holes in the chassis.

  • Page 103: Removing And Reinstalling The Rack Handles

    Notes: • Use only parts provided by Lenovo. • Depending on the model, your server might look slightly different from the illustrations in this topic. The EMI integrity and cooling of the server are protected by having all drive bays and PCI card slots covered or occupied.
  • Page 104 5. Disconnect the following signal cables from the signal cable connectors on the backplane for server models with 12 3.5-inch hard disk drive bays. • Signal cable for the front controls and LEDs on the right rack handle • Signal cable for the front USB connectors on the left rack handle Figure 47.
  • Page 105 a. On each side of the server, insert the signal cable of the rack handle into the hole in the chassis and then push the signal cable through the hole into the chassis. When the signal cable is protruding from the crack between the side edge of the backplane and the inner side of the chassis, hold the signal cable from the rear and carefully pull it into the chassis until it is stopped by the rack handle.
  • Page 106 c. Connect the signal cable of each rack handle to the corresponding signal cable connector on the backplane for server models with 12 3.5-inch hard disk drive bays. Figure 50. Connecting the rack handle signal cables to the backplane 8. Go to “Completing the parts replacement” on page 186. Removing and reinstalling the rack handles for server models with eight 3.5-inch hard disk drive bays and server models with 2.5-inch hard disk drive bays Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”...

  • Page 107: Removing And Reinstalling The Cooling Shroud

    2. To reinstall the rack handles, insert the small tab on the rack handle into the hole in the chassis. Then, align the screw hole in the rack handle with the corresponding hole in the chassis and install the screw to secure the rack handle on each side of the server. Figure 52.
  • Page 108 2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat, clean, and static-protective surface. See the Rack Installation Instructions that comes with the server. 3. Remove the server cover. See “Removing the server cover” on page 85. 4.

  • Page 109: Removing And Reinstalling The Left Cage

    Attention: For proper cooling and airflow, reinstall the cooling shroud before turning on the server. Operating the server with the cooling shroud removed might damage server components. Removing and reinstalling the left cage Attention: Do not open your server or attempt any repair before reading and understanding “Safety information” on page iii and “Guidelines”...
  • Page 110 8. Remove the two screws that secure the left cage and then slide the left cage out of the front of the chassis. Figure 55. Removing the left cage 9. To reinstall the left cage, carefully route the cables from the left cage through the left cage hole in the front and then slide the left cage into the chassis until it snaps into position.

  • Page 111: Installing Or Removing A Memory Module

    10. Ensure that the two screw holes in the rear of the left cage are aligned with the corresponding holes in the chassis. Then, install the two screws to secure the left cage in position. Figure 57. Installing the screws to secure the left cage 11.
  • Page 112 See “Viewing information in the Setup Utility program” on page 61. For a list of the supported ThinkServer memory module options, go to: http://www.lenovo.com/thinkserver The following illustration shows the locations of all memory slots on a system board that has two microprocessors (also known as CPUs) installed.
  • Page 113 The following table explains the memory module installation rules for servers that have only one microprocessor (CPU1) installed. The “X” mark indicates the memory slots into which the memory modules should be installed in different situations. Note: All memory modules to be installed on a server must be the same type (LV RDIMM, RDIMM, or UDIMM) with the same rank, voltage, and frequency.

  • Page 114: Installing A Memory Module

    The following table explains the memory module installation rules for servers that have two microprocessors (CPU1 and CPU2) installed. The “X” mark indicates the memory slots into which the memory modules should be installed in different situations. Note: All memory modules to be installed on a server must be the same type (LV RDIMM or RDIMM) with the same rank, voltage, and frequency.
  • Page 115 To install a memory module, do the following: 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2.

  • Page 116: Removing A Memory Module

    9. Position the new memory module over the memory slot. Ensure that the notch on the new memory module is aligned with the key in the memory slot. Then, press the new memory module straight down into the memory slot until the retaining clips close and the new memory module snaps into position. Note: If there is a gap between the memory module and the retaining clips, the memory module has not been correctly installed.

  • Page 117: Installing Or Removing The Raid Card

    6. Disconnect any cables that might impede your access to the memory slots. 7. Locate the memory module that you want to remove and open the retaining clips on both ends of the memory slot. Then, grasp the memory module by its edges and carefully pull it straight up to remove it from the memory slot.
  • Page 118 • Depending on the specific type, your RAID card might look different from the illustrations in this topic. • Use any documentation that comes with the RAID card and follow those instructions in addition to the instructions in this topic. To install the RAID card, do the following: 1.

  • Page 119: Removing The Raid Card

    8. Note the dotted lines in the following illustration to properly position the new RAID card near the longer PCI Express card slot on the riser card assembly 1. Then, carefully press the new RAID card straight into the slot until it is securely seated and its bracket also is secured by the riser card assembly 1. Figure 65.
  • Page 120 • The RAID card is extremely sensitive to ESD. Ensure that you read and understand “Handling static-sensitive devices” on page 84 first and carefully perform the operation. • Depending on the specific type, your RAID card might look different from the illustrations in this topic. •...

  • Page 121: Installing Or Removing The Thinkserver Raid 500 Upgrade Key For Advanced Raid

    Advanced RAID (hereinafter referred to as the TR 500 Key). The TR 500 Key expands the capability of the ThinkServer RAID 500 Adapter by activating RAID 5 and RAID 50 for advanced SATA/SAS hardware RAID. You can purchase a TR 500 Key from Lenovo. Installing the TR 500 Key Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”...
  • Page 122 6. Locate the RAID 5 key connector on the ThinkServer RAID 500 Adapter and then carefully insert the TR 500 Key into the connector. If necessary, you can remove the ThinkServer RAID 500 Adapter first, install the TR 500 Key on it, and then reinstall the ThinkServer RAID 500 Adapter. See “Installing or removing the RAID card”...

  • Page 123: Installing Or Removing The Thinkserver Raid 700 Battery

    1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat, clean, and static-protective surface.
  • Page 124 alternative to using an uninterruptible power supply, and a second level of fault tolerance when used in conjunction with an uninterruptible power supply. The temperature of the TR 700 Battery is generally 15-20°C (59-68°F) higher than the ambient temperature during fast charge. Therefore, to complete a recharge cycle, the ambient temperature should be lower than 55°C (131°F).
  • Page 125 8. Position the TR 700 Battery above the ThinkServer RAID 700 Adapter so that the board-to-board connector on the bottom of the TR 700 Battery is aligned with the connector on the ThinkServer RAID 700 Adapter; and the three mounting studs on the bottom of the TR 700 Battery are aligned with the corresponding holes in the ThinkServer RAID 700 Adapter.

  • Page 126: Installing Or Removing The Expander Card

    • Use any documentation that comes with the TR 700 Battery and follow those instructions in addition to the instructions in this topic. To remove the TR 700 Battery, do the following: 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server.

  • Page 127: Installing The Expander Card

    Notes: • The server must have a RAID card and an expander card installed to support more than eight hard disk drives. • The expander card is extremely sensitive to ESD. Ensure that you read and understand “Handling static-sensitive devices” on page 84 first and carefully perform the operation. Installing the expander card Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”...
  • Page 128 6. There are two PCI Express card slots on the riser card assembly 1 and the shorter one is for installing the expander card. Remove the slot bracket for the shorter slot and store it in the event that you later remove the expander card and need the bracket to cover the place.

  • Page 129: Removing The Expander Card

    9. Connect cables depending on your specific server configuration. See “Mini-SAS to mini-SAS signal cable connections” on page 44. 10. Reinstall the riser card assembly 1. See “Replacing the riser card assembly 1” on page 163. What to do next: •...

  • Page 130: Installing Or Removing An Ethernet Card

    6. There are two PCI Express card slots on the riser card assembly 1 and the expander card is installed in the shorter slot. Disconnect cables from the expander card. Then, grasp the expander card by its edges and carefully pull it out of the PCI Express card slot. Note: The expander card might fit tightly into the PCI Express card slot.
  • Page 131 This topic provides instructions on how to install an Ethernet card. Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. Notes: • Depending on the specific type, the Ethernet card might look different from the illustrations in this topic. •...
  • Page 132 Note: Depending on the specific type, the Ethernet card and its bracket might look different from the following illustrations. a. Carefully remove the screws that secure the Ethernet card and then remove the full-height bracket from the Ethernet card. Figure 75. Removing the full-height bracket from the Ethernet card b.
  • Page 133 Then, transfer the Ethernet card driver from the removable storage device to your server and run the driver file to install the driver. The most up-to-date device drivers for various server models are always available for download on the Lenovo Support Web site at: http://www.lenovo.com/drivers Removing an Ethernet card Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”...
  • Page 134 This topic provides instructions on how to remove an Ethernet card. Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. Notes: • Depending on the specific type, the Ethernet card might look different from the illustration in this topic. •...

  • Page 135: Installing Or Removing The Thinkserver Raid 300 Upgrade Key For Advanced Raid

    The TR 300 Key expands the capability of the system board by activating RAID 5 for the ThinkServer RAID 300 (also known as onboard SAS software RAID). You can purchase a TR 300 Key from Lenovo. Installing the TR 300 Key Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”...
  • Page 136 6. Insert one side of the TR 300 Key under one of the retaining clips on the iButton socket. Then, carefully press the other side of the TR 300 Key straight down until it snaps into position and is secured by the two retaining clips on the iButton socket.
  • Page 137 This topic provides instructions on how to remove the TR 300 Key if your server has one installed on the system board. Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference.
  • Page 138 5. Open the retaining clip on the iButton socket to release the TR 300 Key and then completely remove the TR 300 Key from the iButton socket. Figure 80. Removing the TR 300 Key 6. If you have lifted up the riser card assembly 1, reinstall it into the chassis. See “Replacing the riser card assembly 1”...

  • Page 139: Installing Or Removing The Thinkserver Management Module Premium

    Therefore, working as an integrated solution in your server, the TMM Premium provides an increased level of manageability over the basic server management available. You can purchase a TMM Premium from Lenovo. Installing the TMM Premium Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”...
  • Page 140 • To complete the installation, go to “Completing the parts replacement” on page 186. Then, refer to the ThinkServer Management Module User Guide, which is available for download at http://www.lenovo.com/ThinkServerUserGuides, for more information about server remote management. Removing the TMM Premium Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”...
  • Page 141 Notes: • If you remove the TMM Premium, the iKVM function for server remote management will be unavailable. • Use any documentation that comes with the TMM Premium and follow those instructions in addition to the instructions in this topic. •...

  • Page 142: Installing Or Removing The Thinkserver Trusted Platform Module

    The TPM is a security chip designed by the Trusted Computing Group (TCG) to provide a hardware method of data encryption. It stores passwords, encryption keys, and digital certificates to help provide security solutions and protect the computer. You can purchase a TPM option from Lenovo. Installing the TPM Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”...

  • Page 143: Removing The Tpm

    6. Insert the TPM into the TPM connector on the system board. Figure 83. Installing the TPM 7. If you have lifted up the riser card assembly 1, reinstall it into the chassis. See “Replacing the riser card assembly 1” on page 163. What to do next: •...
  • Page 144 Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. Notes: • If you remove the TPM, the TPM function will be unavailable. • Use any documentation that comes with the TPM and follow those instructions in addition to the instructions in this topic.

  • Page 145: Installing Or Replacing A Hot-Swap Redundant Power Supply

    5. Remove the TPM installed on the TPM connector by lifting it straight up. Note: Carefully handle the TPM by its edges. Figure 84. Removing the TPM 6. If you have lifted up the riser card assembly 1, reinstall it into the chassis. See “Replacing the riser card assembly 1”...
  • Page 146 You can replace the failing hot-swap redundant power supply without turning off the server. Some server models come with only one power supply. You can purchase a hot-swap redundant power supply option from Lenovo. CAUTION: Hazardous moving parts. Keep fingers and other body parts away.
  • Page 147 • If you are installing a hot-swap redundant power supply, locate the bay for the power supply in the rear of your server. Insert a finger into the hole in the metal shield that protects the bay, press the tab in the direction as shown, and then pull the shield out of the chassis.
  • Page 148 2. If you are replacing a hot-swap redundant power supply, press the release tab in the direction as shown and carefully pull the handle at the same time to slide the failing hot-swap redundant power supply out of the chassis. Figure 86.

  • Page 149: Installing Or Replacing A Heat Sink

    5. Connect the power cord to the power cord connector on the new hot-swap redundant power supply. Then, check the status LED near the power cord connector. When the LED is lit in green, it indicates that the hot-swap redundant power supply is working correctly. When the LED is lit in amber, it indicates that the hot-swap redundant power supply is likely to fail or has failed.
  • Page 150 6. If you are replacing a heat sink, remove the four screws that secure the heat sink to the system board. It is recommended that you carefully remove the four screws from the system board using the following method to avoid any possible damage to the system board. a.

  • Page 151: Installing Or Replacing The Microprocessor

    10. Install the four screws to secure the new heat sink on the system board. It is recommended that you carefully install the four screws using the following method to avoid any possible damage to the system board. a. Partially tighten screw , then firmly tighten screw , and then return to screw and firmly tighten...
  • Page 152 1 and the microprocessor socket 2 is protected by a plastic socket cover. You can purchase a microprocessor option kit from Lenovo and install the second microprocessor to expand system capabilities.
  • Page 153 6. Gently press down the small handle on the microprocessor socket and then pull the handle a little bit outward to release it from the secured position. Then, pivot the handle upward to the fully open position. Then, gently press the microprocessor retainer to open it. Figure 90.
  • Page 154 9. Remove the protective cover that protects the gold contacts on the bottom of the new microprocessor. Do not touch the pins on the microprocessor socket and the gold contacts on the bottom of the new microprocessor. Figure 92. Do not touch the pins 10.

  • Page 155: Replacing The Microprocessor

    11. Carefully close the microprocessor retainer. Then, carefully close the small handle to lock the retainer into position and secure the new microprocessor in the socket. Figure 94. Securing the microprocessor in the socket 12. Install the new heat sink that comes with the microprocessor option kit. See “Installing or replacing a heat sink”...
  • Page 156 Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. Notes: • Ensure that the new microprocessor is the correct type your server supports. See “Features” on page 8. When two microprocessors are installed, both must have the same core voltage and core speed.
  • Page 157 7. Ensure that the small handle and the microprocessor retainer are in the fully open position. Touch only the edges of the microprocessor and carefully lift it straight up and out of the microprocessor socket. Place the old microprocessor on a static-protective surface. Notes: •...
  • Page 158 10. Note the orientation of the new microprocessor. Hold the new microprocessor by its edges and align the notches on it with the tabs in the microprocessor socket. Then, carefully lower the new microprocessor straight down into the microprocessor socket. Note: The small triangle on one corner of the new microprocessor is the microprocessor orientation indicator.

  • Page 159: Installing Or Replacing The Optical Drive

    11. Carefully close the microprocessor retainer. Then, carefully close the small handle to lock the retainer into position and secure the new microprocessor in the socket. Figure 99. Securing the microprocessor in the socket 12. Reinstall the heat sink. See “Installing or replacing a heat sink” on page 135. 13.
  • Page 160 CAUTION: When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are installed, note the following: • Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device. •...
  • Page 161 • If you are replacing an optical drive, disconnect the signal cable and the power cable from the rear of the optical drive. Press the rear of the retaining bracket in the direction as shown and push the optical drive from the rear until it is projected from the front of the chassis. Then, hold the optical drive from the front and completely slide it out of the chassis.
  • Page 162 7. Remove the retaining bracket from the old optical drive or the dummy optical drive tray. Then, install it on the side of the new optical drive. Figure 102. Installing the optical drive retaining bracket ThinkServer RD430 Hardware Maintenance Manual...
  • Page 163 8. Slide the new optical drive with the retaining bracket into the drive bay from the front until it snaps into position. Figure 103. Installing the optical drive for server models with 3.5-inch hard disk drives Figure 104. Installing the optical drive for server models with 2.5-inch hard disk drives Chapter 6 Installing, removing, or replacing hardware...

  • Page 164: Installing Or Replacing A Hot-Swap Hard Disk Drive

    This topic provides instructions on how to install or replace a hot-swap hard disk drive. For a list of the ThinkServer hard disk drive options, go to: http://www.lenovo.com/thinkserver You can install a new hot-swap hard disk drive or replace a failing hot-swap hard disk drive without turning off the server, which helps you avoid significant interruption to the operation of the system.
  • Page 165 • For hard disk drives with different capacities, install the hard disk drives following the order of the hard disk drive bays as well as the order from the lowest capacity to the highest capacity. Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference.
  • Page 166 Figure 107. Opening the handle of a 2.5-inch hot-swap hard disk drive or dummy tray 2. Pull the handle and carefully slide the hot-swap hard disk drive or the dummy tray out of the front of the chassis. Figure 108. Removing the 3.5-inch hot-swap hard disk drive or dummy tray ThinkServer RD430 Hardware Maintenance Manual...
  • Page 167 Figure 109. Removing the 2.5-inch hot-swap hard disk drive or dummy tray 3. Touch the static-protective package that contains the new hot-swap hard disk drive to any unpainted surface on the outside of the server. Then, take the new hot-swap hard disk drive out of the package. Note: Do not touch the circuit board on the hard disk drive.

  • Page 168: Replacing The Thinkserver Raid Super Capacitor Module

    This topic applies only to server models that have a ThinkServer RAID Super Capacitor Module installed. The ThinkServer RAID Super Capacitor Module protects the cache memory on the installed ThinkServer RAID 710 Adapter. You can purchase a ThinkServer RAID Super Capacitor Module from Lenovo. ThinkServer RD430 Hardware Maintenance Manual...
  • Page 169 Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. Notes: • Depending on the model, your server might look slightly different from the illustrations in this topic. •...
  • Page 170 5. Gently press the tab on the bracket and remove the ThinkServer RAID Super Capacitor Module from the bracket at the same time. Figure 113. Removing the ThinkServer RAID Super Capacitor Module from the bracket 6. Touch the static-protective package that contains the new ThinkServer RAID Super Capacitor Module to any unpainted surface on the outside of the server.

  • Page 171: Replacing The Hot-Swap Hard Disk Drive Backplane

    8. Position the new ThinkServer RAID Super Capacitor Module with the bracket on the cooling shroud as shown so that one side of the bracket is secured by the two tabs . Then, press the other side of the bracket straight down until the tab passes through the corresponding hole in the bracket and secures the bracket in place.
  • Page 172 Note: To clearly show the backplane, the system fans are omitted from the illustrations in this topic. To replace the backplane for server models with eight 3.5-inch hard disk drive bays, do the following: 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server.
  • Page 173 9. Touch the static-protective package that contains the new hot-swap hard disk drive backplane to any unpainted surface on the outside of the server. Then, remove the new backplane from the package. Note: Carefully handle the backplane by its edges. 10.
  • Page 174 14. If you are instructed to return the old hot-swap hard disk drive backplane, follow all packaging instructions and use any packaging materials that are supplied to you for shipping. What to do next: • To work with another piece of hardware, go to the appropriate section. •...
  • Page 175 8. Touch the static-protective package that contains the new hot-swap hard disk drive backplane to any unpainted surface on the outside of the server. Then, remove the new backplane from the package. Note: Carefully handle the backplane by its edges. 9.
  • Page 176 3. Remove the server cover. See “Removing the server cover” on page 85. 4. Locate the backplane. See “Components of server models with 2.5-inch hard disk drive bays” on page 34. 5. Remove all the installed 2.5-inch hot-swap hard disk drives and dummy trays (if any) from the hard disk drive cage (right cage or middle cage).

  • Page 177: Replacing The Riser Card Assembly 1

    9. Note the orientation of the new backplane. Carefully press the new backplane straight down into the chassis so that it is secured in place by the tabs on the chassis and the three screw holes in the new backplane are aligned with the corresponding holes in the chassis. Then, install the screws to secure the new backplane in place.
  • Page 178 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat, clean, and static-protective surface.

  • Page 179: Replacing The Riser Card Assembly 2

    11. Position the new riser card assembly 1 on the chassis and align it with the riser card assembly 1 slot on the system board and align the rear of it with the corresponding rail guides in the rear of the chassis. Then, carefully press the new riser card assembly 1 straight down into the chassis until it is fully seated.
  • Page 180 2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat, clean, and static-protective surface. See the Rack Installation Instructions that comes with the server. 3. Remove the server cover. See “Removing the server cover” on page 85. 4.

  • Page 181: Replacing The Front Panel Board

    10. Position the new riser card assembly 2 on the chassis and align it with the riser card assembly 2 slot on the system board and align the rear of it with the corresponding rail guides in the rear of the chassis. Then, carefully press the new riser card assembly 2 straight down into the chassis until it is fully seated.

  • Page 182: Drive Bays

    Notes: • The front panel board is extremely sensitive to ESD. Ensure that you read and understand “Handling static-sensitive devices” on page 84 first and carefully perform the operation. • Depending on the model, your server might look slightly different from the illustrations in this topic. Replacing the front panel board for server models with eight 3.5-inch hard disk drive bays Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”...
  • Page 183 8. Carefully position the new front panel board on the chassis so that the front controls, connectors, and LEDs are through the corresponding holes in the front bezel and the two screw holes in the new front panel board are aligned with the corresponding mounting studs on the chassis. Then, install the screws to secure the front panel board in place.
  • Page 184 8. Disconnect the front panel cable and the front panel USB cable from the rear of the front panel board. 9. Remove the two screws that secure the front panel board and then carefully remove the front panel board from the left cage. Figure 130.

  • Page 185: Replacing The Diagnostic Module

    What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the replacement, go to “Completing the parts replacement” on page 186. Replacing the diagnostic module This topic provides instructions on how to replace the diagnostic module. For detailed information about the diagnostic module, see “Diagnostic module”...
  • Page 186 6. Press the release tab in the direction as shown and then push the diagnostic module out of the front of the chassis. Figure 132. Removing the diagnostic module for server models with eight 3.5-inch hard disk drive bays 7. Touch the static-protective package that contains the new diagnostic module to any unpainted surface on the outside of the server.
  • Page 187 10. If you are instructed to return the old diagnostic module, follow all packaging instructions and use any packaging materials that are supplied to you for shipping. What to do next: • To work with another piece of hardware, go to the appropriate section. •...

  • Page 188: Replacing A System Fan

    12. Slide the new diagnostic module into the cage from the front until it snaps into position. Figure 135. Installing the diagnostic module into the left cage of server models with 2.5-inch hard disk drive bays 13. Connect the diagnostic module cable to the rear of the new diagnostic module. 14.
  • Page 189 To replace a system fan, do the following: 1. Remove the server cover. See “Removing the server cover” on page 85. Note: The system fans are hot-swap and you can replace a failing system fan without turning off the server. 2.

  • Page 190: Replacing The System Board Battery

    5. Position the new system fan above the place for the removed failing system fan so that the system fan connector on the bottom of the new system fan is facing the rear of the chassis. Then, press the new system fan straight down until it is seated into place.
  • Page 191 DANGER Danger of explosion if battery is incorrectly replaced. When replacing the lithium coin cell battery, use only the same or an equivalent type that is recommended by the manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of.

  • Page 192: Replacing The System Board

    “Guidelines” on page 83. This topic provides instructions on how to replace the system board. Note: This procedure must be performed only by trained service personnel of Lenovo. CAUTION: Hazardous moving parts. Keep fingers and other body parts away.
  • Page 193 CAUTION: The heat sinks and microprocessors might be very hot. Turn off the server and wait three to five minutes to let the server cool before removing the server cover. Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference.
  • Page 194 9. Remove the power supply cooling shroud. Figure 141. Removing the power supply cooling shroud 10. Remove all memory modules. See “Removing a memory module” on page 102. 11. Remove the TMM Premium if one is installed. See “Removing the TMM Premium” on page 126. 12.
  • Page 195 15. Disconnect all cables from the system board. Then, remove the ten screws that secure the system board following the recommended numerical sequence as shown. Figure 142. Removing the screws that secure the system board Chapter 6 Installing, removing, or replacing hardware...
  • Page 196 16. Gently lift each edge of the system board a little bit upward so that the system board is released from the mounting studs on the chassis. Then, move the system board to the front of the server and then carefully pivot the system board upward to remove it out of the chassis.
  • Page 197 19. Install the ten screws following the recommended numerical sequence as shown to secure the new system board on the chassis. Figure 145. Installing the screws to secure the system board 20. Remove the microprocessors from the old system board and install them on the new system board. See “Installing or replacing the microprocessor”...
  • Page 198 b. Position the microprocessor socket cover above the microprocessor socket so that the small triangle on the socket cover faces the small triangle on the microprocessor retainer. Then, carefully press the socket cover straight down into the socket until it snaps into position. Figure 146.
  • Page 199 24. Note the orientation of the power supply cooling shroud and install it into the chassis by inserting the two small tabs on the bottom of the shroud into the corresponding holes in the power supply cage. Figure 148. Installing the power supply cooling shroud 25.

  • Page 200: Completing The Parts Replacement

    30. Install any other parts that you have removed and connect all cables to the new system board. Refer to the information that you have recorded and the related topics in “Installing, removing, or replacing hardware” on page 88. 31. If you are instructed to return the old system board, follow all packaging instructions and use any packaging materials that are supplied to you for shipping.
  • Page 201 2. Ensure that all internal cables are connected and routed correctly and secured by any cable clips or ties in the server. Keep cables clear of the hinges and sides of the chassis to avoid interference with reinstalling the cooling shroud and the server cover. The following illustration shows an example of the cable routing in the chassis with two backplanes for 16 2.5-inch hard disk drives.
  • Page 202 5. Ensure that the cover latch is in the open position. Place the server cover above the chassis so that the cover latch is aligned with the cover latch slot in the chassis. Then, lower the server cover onto the chassis until the cover latch is inserted into its slot and both sides of the server cover engage the guides on both sides of the chassis.

  • Page 203: Updating The Server Configuration

    Attention: To avoid component damage, connect the power cords last. Note: In most areas of the world, Lenovo requires the return of the defective CRU. Information about this will come with the CRU or will come a few days after the CRU arrives.
  • Page 204 ThinkServer RD430 Hardware Maintenance Manual...

  • Page 205: Chapter 7. Troubleshooting And Diagnostics

    (some models). The various LEDs help you easily identify the system and device status and diagnose problems. For information about the LEDs, refer to the related topics in “Locations” on page 13. © Copyright Lenovo 2012...

  • Page 206: Using A Diagnostic Program

    • ThinkServer System Profile Collection Tool To use a diagnostic program, do the following: 1. Go to http://www.lenovo.com/drivers and follow the instructions on the Web page to locate a diagnostic program. 2. Download and unzip the diagnostic program package to get the diagnostic program package folder.

  • Page 207: Optical Drive Problems

    Symptom Action The ThinkServer EasyStartup DVD does not start. 1. Ensure that the server supports the ThinkServer EasyStartup program and has a bootable DVD drive installed or a bootable external DVD drive attached. 2. Ensure that you have set the optical drive with the ThinkServer EasyStartup DVD installed as the first startup device.

  • Page 208: Hard Disk Drive Problems

    Symptom Action 4. Replace the signal cable for the optical drive. 5. Replace the power cable for the optical drive. 6. Replace the power cable for the backplane. 7. Replace the optical drive. 8. Replace the backplane. 9. (Trained service technician only) Replace the system board.

  • Page 209: Memory Module Problems

    Symptom Action 6. Ensure that the cable connection is correct. See “Mini-SAS to mini-SAS signal cable connections” on page 44. 7. Reconnect the backplane power cable and repeat step 1 through step 4. 8. Reconnect the backplane signal cable and repeat step 1 through step 4.

  • Page 210: Keyboard, Mouse, And Usb Device Problems

    Keyboard, mouse, and USB device problems Follow the suggested actions for the corresponding symptom in the order in which they are listed until the problem is solved. If none of these actions solve the problem, see “Troubleshooting procedure” on page 191 for the subsequent steps you should check after using the information in this topic.

  • Page 211: Chapter 8. Getting Information, Help, And Service

    Using the documentation Information about your Lenovo system and installed software, if any, or optional device is available in the documentation that comes with the product. The documentation can include printed documents, online documents, readme files, and help files. Most of the documentation for your server is on the documentation DVD provided with your server.

  • Page 212: Help And Service

    • Check the power switches to ensure that the system and optional devices are turned on. • Use the troubleshooting information in your system documentation on the documentation DVD that comes with your product. • Check for the updated information, new device drivers, and hints and tips on the Lenovo Support Web site at: http://www.lenovo.com/support If possible, be at your product when you call.

  • Page 213: Using Other Services

    Service availability and service names might vary by country or region. For more information about these services, go to the Lenovo Web site at: http://www.lenovo.com...
  • Page 214 ThinkServer RD430 Hardware Maintenance Manual...

  • Page 215: Appendix A. Notices

    Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any Lenovo intellectual property right may be used instead.

  • Page 216: Trademarks

    Trademarks Lenovo, the Lenovo logo, and ThinkServer are trademarks of Lenovo in the United States, other countries, or both. Intel and Intel Xeon are trademarks of Intel Corporation in the United States, other countries, or both. Internet Explorer, Microsoft, Windows, and Windows Server are trademarks of the Microsoft group of companies.

  • Page 217: Polyvinyl Chloride (Pvc) Cable And Cord Notice

    Lenovo encourages owners of information technology (IT) equipment to responsibly recycle their equipment when it is no longer needed. Lenovo offers a variety of programs and services to assist equipment owners in recycling their IT products. For information on recycling Lenovo products, go to: http://www.lenovo.com/recycling...

  • Page 218: Requirement For Batteries Containing Perchlorate

    Perchlorate Material - special handling may apply, See http://www.dtsc.ca.gov/hazardouswaste/perchlorate Important WEEE information The WEEE marking on Lenovo products applies to countries with WEEE and e-waste regulations (for example, European Directive 2002/96/EC, India E-Waste Management & Handling Rules, 2011). Appliances are ThinkServer RD430 Hardware Maintenance Manual...

  • Page 219: German Ordinance For Work Gloss Statement

    Lenovo is proud to offer our customers products with an ENERGY STAR compliant designation. Some models of the following machine types have been designed and tested to conform to the ENERGY STAR program requirement for computer servers at the time of manufacture: 3057, 3059, 3061, 3064, 3065, 3069, 3070, 3071, and 4306.
  • Page 220 For more information about ENERGY STAR, go to: http://www.energystar.gov Lenovo encourages you to make efficient use of energy an integral part of your day-to-day operations. To help in this endeavor, set the following power-management features to take effect when your servers have been used: •...

  • Page 221: Index

    CRU identification updating flashing the BIOS front bezel devices, handling static-sensitive reinstalling diagnostic module removing locations front panel replacing diagnostic panel locations front panel board locations replacing diagnostic program front view of the server © Copyright Lenovo 2012...
  • Page 222 Lenovo Rack Planner virtual drive software Input/Output (I/O) Lenovo ThinkServer EasyManage features software installation rules Lenovo ThinkServer EasyManage program DIMM using memory module locations installing LSI Software RAID Configuration Utility program DIMM interface Ethernet card starting...
  • Page 223 1 riser card assembly 2 system board system board battery rack handles system fan reinstalling ThinkServer RAID Super Capacitor Module removing riser card assembly 1 RAID replacing configuring riser card assembly 2 introduction replacing RAID array © Copyright Lenovo 2012...
  • Page 224 road map system board switches server setup locations running system date consistency check setting system event log troubleshooting and diagnostics system fan features Save & Exit menu replacing Setup Utility program system fan error Security menu 24–25, 57 Setup Utility program system identification (ID) server components 19, 22, 31...
  • Page 225 TÜV gloss statement updating firmware server configuration the BIOS updating or recovering the BIOS using documentation EasyUpdate Firmware Updater program Lenovo ThinkServer EasyManage program passwords Setup Utility program ThinkServer EasyStartup program video subsystem features viewing information Setup Utility program virtual drive initializing...
  • Page 226 ThinkServer RD430 Hardware Maintenance Manual...

This manual is also suitable for:

306530593069307030714306 ... Show all

Table of Contents