Standby And Power On/Off Buttons; Volume Knob And Volume +/- Buttons; Input Buttons; Zone Button - Rotel RSX-1562 Owner's Manual

26
You can also set the CD codes for PLAY, STOP, FAST FORWARD, REV etc,
from the factory default IR code 1 to 2, if you find the unit is interfering
with other Rotel CD players in your system.
To change the CD code, point the remote at the unit and press "CD" and
2 (1) keys at the same time. Release the "CD" key and continue to press
the 2 (1) key for more than 5 seconds until the unit changes the code.
Overview of Buttons and Controls
This section provides a basic overview of the buttons and controls on the
front panel and the remote control. Detailed instructions on the use of
these buttons are provided in the more complete operating instructions
in the following sections.
STANDBY and Power ON/OFF Buttons
2
The front-panel STANDBY button and the remote control ON/OFF button
activate or deactivate the unit. The rear panel master POWER switch must
be in the ON position for the remote standby function to operate.

VOLUME Knob and VOLUME +/- Buttons

The VOLUME +/- buttons on the remote and the large rotary control on
the front panel provide the master VOLUME control, adjusting the output
level of all channels simultaneously.
DISPLAY (DISP) Button
D
Push this toggle button to display the current Audio and Video source,
input mode and output mode. To change Dynamic Range, push the DISP
button then push DOWN and Left/Right keys to adjust.
RCVR SETUP Button
E
Navigating and Select (ENT) keys
The RCVR SETUP button pulls out the OSD on the TV. Use the navigation
keys UP/DOWN/Left/Right and ENT to access the various menus.
Note: The MENU button on the remote control will not operate with
the RSX-1562 without additional programming by your dealer.
MUTE Button
uB
Push the MUTE button once to turn the sound off. An indication appears
in the front panel and on-screen displays. Press the button again to restore
previous volume levels.

INPUT Buttons

5weM
This button on the front panel can be used to change sources.

ZONE Button

r
This button serve as a standby button for the currently selected remote
zone, toggling the zone on or off.
SEL Button
tJ
This button can be used to select the desired zone fro additional
changes such as changing the input, adjusting the volume, or turning
a remote zone on or off. Repeatedly press the button until the desired
zone appears in the front panel: RECORD > ZONE 2 > ZONE 3 >
ZONE 4. Once the desired zone appears, you have 10 seconds to
make the desired change. Change the input selection by pressing an
INPUT button. When ZONES 2-4 appear, you can also adjust the
volume, or turn the zone on or off by pressing the ZONE button.
A
q C
F
RSX-1562 SURROUND SOUND RECEIVER
MODE buttons SUR+
7y
The MODE buttons/SUR+ button serve to display surround mode information
of current listing/viewing media, which can be set when selecting input
source. On the remote, press SUR+ key, then use the Left/Right navigation
keys to change the mode.
Other buttons on the remote and front panel can directly access specific
modes.
2CH: change the audio mode to STEREO, DOWN MIX or BYPASS.
PLIIx MODE: change the Pro-Logic mode.
DSP: Changes the DSP decode mode (analog) from DSP1 - 4, 5/7 CH
Stereo.
PLCM: toggles the audio mode to Pro Logic Cinema or Music.

Playback buttons

L
These buttons provide basic control functions for iPod/USB AUDIO
playback.
PLAY / button: Start playing the selected media
STOP . button: Stop current playing track, press / button to resume
Push STOP key for 5 seconds to safely remove the
USB device from the front socket.
PAUSE , button: Temporarily suspend play
PREVIOUS { button: One push -Skip to start of current track
Two pushes Skip to previous track.
NEXT } button: Skip to next track.
RND Button
I
This button can be used for the front USB connection and put the music
played in random/shuffle mode.
P-EQ Button/Knobs
6D
Used to display the EQ Frequency level and GAIN. Also can be used
for temporary adjustments of EQ. Push P-EQ button and use the UP/
Down keys to adjust GAIN value. Use the Left/Right keys to skip to
the next frequency. From the front panel, push the FREQ knob to bring
up the EQ value. Turn the knob to change the frequency. Turn the
parametric EQ knob to adjust the GAIN value.
For permanent EQ and GAIN adjustments, please enter the value in
the EQ setup menu.

SPKR Button

D
This button can access the various speaker setting and adjust the
output level for each speaker in the system. Use the navigations
keys to change values. This is only a temporary change. To make
permanent adjustments, please access the TEST TONE setting from the
OSD.
MEM Button
H
For setting up tuner presets into memory, see Tuner Control section.

Party Mode: Selecting the Same input for all outputs

You may wish to have the same input for listening, recording and all
of the remote zones. The RSX-1562 makes this configuration easy,
(called party mode) by linking inputs for recording and remote zones.
J
rtJ