High Definition Tv Monitor Outputs; Hdmi Monitor Outputs L; Multi Inputs; Preamp Outputs - Rotel RSX-1562 Owner's Manual

20
High Definition TV Monitor Outputs
Two HDMI outputs of the unit send the High Definition video signals
to your TV monitor. The HDMI outputs can send all enhanced or high
definition video signals to a high-definition TV 2D (480p/576p, 720p,
1080i, or 1080p) and 3D (up to 1080p/24Hz).
The output resolution is specified in the VIDEO/HDMI setup menu. Analog
video signals (Composite and Component) in any resolution can be
converted to the desired resolution, except 3D and 1080p 24Hz signals
at the HDMI outputs.
Note: HDMI Video signals are passed through without scaling.
Note: If the TV can not show the currently set HDMI resolution, press
"2CH" and "MUTE" keys together on the front panel to change the
resolution to 480p/576p.
HDMI Monitor Outputs
l
There are two HDMI Outputs which send out HDMI signals in parallel.
The same signal is sent to both outputs at the same time. Only HDMI
output 1 is ARC enabled. Connect your ARC enabled TV's HDMI
input to this output.
Note: Your TV will most likely have more than one HDMI inputs. Not
all of them will be ARC enabled. Please use the ARC enabled HDMI
input of your TV. It should be labeled ARC next to the input.
Additional information for high definition outputs:
• Typically, choose the HDMI outputs with digital high-definition TVs
such as LCD, plasma, or DLP monitors. Use the Component Video
connections with analog high definition TVs such as CRT-based
direct view or projection monitors.
• HDTV Component Video output is subject to HDCP copy protection.
It may not display 720p,1080i or 1080p resolution when the
source signal incorporates copy protection. However, when Video
Out is set to 480p/576p in the VIDEO/HDMI menu, all sources
will be available.
• The video signal sent to the TV through the HDMI connection will
not be displayed properly unless all HDMI components in the
system, including the TV monitor, are compatible with the HDCP
copy protection standard.
• Only audio signals passed-through directly from the source component
are sent to the TV set through the HDMI connection. To send decoded
audio from the RSX-1562 to the TV, you must select 'TV mode' in
the VIDEO/HDMI menu.
• TV monitors with DVI-D connections can usually be connected to
the HDMI output of the receiver with the use of an appropriate
24-pin DVI-HDMI adaptor. However , there are occasionally some
incompatibilities with older DVI-D equipped monitors.
• Use the scaler setting of the RSX-1562's Analog Video Output to
match the resolution of your TV.
• 3D Video is only available through the HDMI outputs.
l
RSX-1562 SURROUND SOUND RECEIVER
Audio Inputs and Outputs
This Rotel receiver provides both analog and digital audio
connections.
VIDEO 1–6 Audio Inputs
c
Six pairs of RCA inputs (VIDEO IN 1–6) provide connections for Left/
Right analog audio signals from six additional source components.
These inputs have corresponding video inputs and are used for VCRs,
satellite TV tuners, DVD players, etc. However, they may also be used for
additional audio only components, simply by omitting the corresponding
video connections.
VIDEO Out Audio Output
v
One pair of RCA jacks (VIDEO OUT) provide connections for sending line
level left and right analog audio signals for recording to a VCR.
This connection can be assigned to any analog audio connection.
CD Inputs
x
A Left/Right pair of RCA analog audio inputs for connecting a CD
player .

MULTI Inputs

b
A set of RCA inputs accept up to 7.1 channels of analog signals from
a DVD-A or SACD player. There are inputs for FRONT L & R, CENTER,
SUB, REAR L & R, and CENTER BACK 1 & 2 or FRONT VERTICAL
HEIGHT L & R in a Dolby PLIIz setup.
These inputs bypass all digital processing in the receiver and are routed
directly to the Volume control and preamp outputs.
There are two subwoofer options for the MULTI input. Normally, the .1
channel input is passed through directly to the subwoofer output. An
optional bass redirect feature duplicates the seven main channels, sums
them, and sends this mono signal through a 100Hz analog low filter
to the subwoofer output. This provides an unaltered analog bypass for
the seven main channels along with a subwoofer signal derived from
those channels.

Preamp Outputs

n
A group of ten RCA analog audio outputs sends the RSX-1562's line
level output signals to external amplifiers and powered subwoofers.
These outputs are variable level, adjusted by the RSX-1562's volume
control. The ten connectors provide output for: FRONT L & R, CENTER 1
& 2, SURROUND (REAR) L & R, CENTER BACK CB1 & CB2(or FRONT
VERTICAL HEIGHT L & R), and SUBWOOFER 1 & 2.
Note: Depending on your system configuration, you may use some or all
of these connections. For example, if you only have one center channel,
connect it to the CENTER 1 output. If you only have one center back
channel, connect it to the CB1 output.
Digital Inputs
\
The RSX-1562 accepts digital inputs from source components such as CD
players, satellite TV tuners, and DVD players. The built-in digital receiver
senses the correct sampling rates.
Note: With a digital input connection, the receiver will be used to
decode the signal, rather than the source component's internal decoders.
You must use digital connections for a DVD player that supplies a Dolby