Related Manuals for Draper CS14A
Summary of Contents for Draper CS14A
- Page 1 350mm (14") CHOP SAW STOCK No.55809 (110V). PART No.CS14A. 52623 (230V). • INSTRUCTIONS • IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFE AND EFFECTIVE USE OF THIS TOOL. 09/98...
-
Page 2: Table Of Contents
Operation ............................Service requirements and maintenance ..................... Trouble shooting ..........................10 DECLARATION OF CONFORMITY Draper Tools Ltd. Hursley Road, Chandlers Ford, Eastleigh, Hampshire. SO53 1YF. England. Declare under our sole responsibility that the product: Part Number:- CS14A. Stock No. 55809 (110V). -
Page 3: Specification/Guarantee
This guarantee applies in lieu of any other guarantee expressed or implied and variations of its terms are not authorized. Your Draper guarantee is not effective unless you can produce upon request a dated receipt or invoice to verify your proof of purchase within the 12 month period. -
Page 4: General Safety Instructions
Please read the following instructions carefully, failure to do so could lead to serious personal injury. IMPORTANT This machine was designed for metal cutting applications only. Draper Tools Limited recommends that this machine should not be modified or used for any application other than that for which it was designed. If you are unsure of its relative applications do not hesitate to contact us in writing and we will advise you. -
Page 5: Safety Rules For Chop Saw
SAFETY RULES FOR CHOP SAWS 1. WARNING: Do not operate your abrasive 18. MAKE SURE abrasive wheel is not contacting cut-off saw until it is completely assembled workpiece before switch is turned on. and installed according to the instructions. 19. ALLOW the motor to come up to full speed 2. -
Page 6: Power Supply
(i.e. red). Fuse covers are available from your Draper Tools stockist. If the fitted plug is not suitable, it should be cut off and destroyed. *The end of the cable should now be suitably prepared and the correct type of plug fitted. -
Page 7: Unpacking
Fig.1 Now referring to Fig.1. carefully check that all the parts are present. Please contact the Draper Power Helpline (01703) 494344 if you have any enquiries i.e. problems with assembly, apparent missing/damaged parts, help with accessories available or technical advice. -
Page 8: Know Your Chop Saw
KNOW YOUR CHOP SAW Fig.2 ✕✌ ✕✙✌ ✖✌ ✜✌ ✗✌ ✘✌ ✙✌ ✢✌ ✕✗✌ ✕✚✌ ✕✔✌ ✕✖✌ ✚✌ ✕✛✌ ✛✌ ✕✕✌ ✕✘✌ ✕✌ Trigger locking button ✕✔✌ Depth stop ✖✌ Trigger switch ✕✕✌ Lock nut ✗✌ Transportation handle ✕✖✌ Backstop ✘✌... -
Page 9: Assembly
ASSEMBLY 1. This cut-off saw is shipped with the cutting head Fig.3. locked in the down position as shown in Fig.3. ✪✌ 2. Pull locking pin ✪✌ Fig.3. to enable the cutting Fig.4. head to be in the up position as shown in Fig.3. 3. -
Page 10: Operation
OPERATION 1. On-off switch Fig.7. To start the chop saw, depress the trigger locking button ✮✌ and press the trigger switch ✯✌. The ✮✌ saw can now be operated until the trigger is ✰✌ released Fig.7. ✯✌ NOTE: We suggest that when the machine is not in use, the switch ✯✌... -
Page 11: Service Requirements And Maintenance
SERVICE REQUIREMENTS Brush inspection and replacement. Fig.11. CAUTION: Before inspecting the brushes, disconnect the machine from the power supply ✱✌ BRUSH WEAR AND REPLACING BRUSHES On new machines check for brush wear after the first 50 hours of use, then every 10 hours. Replace brushes when they have worn down to 5mm. -
Page 12: Troubleshooting
TROUBLESHOOTING WARNING: FOR YOUR OWN SAFETY ALWAYS TURN THE MAIN SWITCH ON THE MACHINE “OFF” AND REMOVE THE PLUG FROM THE POWER SUPPLY BEFORE CARRYING OUT ANY MAINTENANCE OR TROUBLESHOOTING. MOTOR Trouble Probable Cause Remedy Motor does not start. 1. Fuse. 1. - Page 13 NOTES...
- Page 14 NOTES...
- Page 15 NOTES...
- Page 16 Published by Draper Tools Ltd. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise without prior permission in writing from Draper Tools Ltd.
Need help?
Do you have a question about the CS14A and is the answer not in the manual?
Questions and answers