Information On Dv Dubbing - Toshiba DVR80KF Owner's Manual

E9TK5FD_EN.book Page 39 Wednesday, January 13, 2010 10:33 AM
When you want to record to a videotape:
Press [VCR].
Insert a videotape with a record tab into the
cassette compartment.
3
Select the input terminal to which the external
equipment is connected (AV1 or AV2).
Press [INPUT SELECT
external input mode, then press [PROG.
repeatedly to select AV1 or AV2.
4
Select a recording mode using [REC MODE].
Refer to "Recording Mode" on page 28 for DVD or page
70 for VHS.
5
Press [I REC] (DVD / VHS) on the unit to start
recording.
6
Press the [PLAY B] button on the external
equipment.
7
For disc:
Press on the unit to stop
[STOP C]
recording.
For videotape:
Press
[STOP EJECT C A]
stop recording.
Note
• During recording, recording will be paused when a signal
other than PAL or SECAM is detected. (See "Video Colour
System" on page 38 for details.)
• The signal from the external device will be output
automatically when the TV is connected to AV1 and the
external device is connected to AV2 using a Scart cable with
its power on. (However, it will not be output when this unit's
power is turned off.)
If you want to monitor this unit's signal, press [DISPLAY]
or turn the external device off. (The signal from this unit can
only be monitored during playback.)
If you want to monitor the signal from other input, press
[DISPLAY], then press [INPUT SELECT
desired external input mode, then select the desired input
channel using [PROG.

Information on DV Dubbing

This function helps you to dub the contents in the DVC (digital
video camcorder) to DVD or VHS easily. (See page 71 for
DVC to VHS Dubbing.)
You can control basic operations of the DVC from the remote
control of this unit if the DVC is in video mode.
Guide to DV and On-Screen Display
1
Connect your DVC to the DV input jack on the
front panel using a DV cable. (Use the DV cable
that has 4-pin input jack and is compliance with
the IEEE 1394 standards.)
2
Press [INPUT SELECT
the external input channel, then press
[PROG. ] repeatedly to select DV(AV3).
3
Press [DISPLAY] to display the DVC information
on the screen.
] repeatedly to select the
]
on the unit to
] to select the
].
] repeatedly to select
When the DVC is in video mode...
1/ 1 1/ 1
T C
1
2
Control DVD
DV Audio Stereo1
Start Rec
3 4
When the DVC is in camera mode...
1/ 1 1/ 1
T C
7
The menu changes according to the mode of DVC.
Switch the mode on the DVC to video mode for the dubbing
information.
The following instructions are described with the
operations using the remote control of this unit.
1 DV icon
2 Indicator of active device
• With "Control" highlighted, press [ENTER OK] to display
the available devices to control with the remote control
of this unit. Select the device you want to operate using
[K L], then press [ENTER OK].
- Select "DVD" to control this unit with the remote control
of this unit.
- Select "DVC" to control your DVC with the remote
control of this unit.
3 Recording audio mode
• "DV Audio" can be changed. With "DV Audio" selected,
press [ENTER OK] to display "DV Audio" menu. Select
the audio you want to output using [K L], then press
[ENTER OK].
- Select "Stereo1" to dub the stereo sound.
- Select "Stereo2" to dub the sound that was added after
the recording.
- Select "Mix" to dub the stereo1 and stereo2.
4 Command menu
• "Start Rec" or "Pause Rec" will appear.
5 External input channel
6 Product name of your DVC
• If the unit cannot recognise the input signal from the
DVC or if it is the unknown product, "No Device" or "****"
will appear instead.
-RW VR ORG
DV
AB-1234
0:12:34
SP 2:00
-RW VR ORG
5
DV
AB-1234
0:12:34
SP 2:00
6
39
EN