Information On Dv Dubbing - Toshiba RDXV49DTKF Owner's Manual

E3TK0FD_EN.book Page 39 Monday, March 9, 2009 10:00 AM
Note
• During recording, recording will be paused when a signal
other than PAL or SECAM is detected. (See "Video Colour
System" on page 38 for details.)
• If the external equipment is connected to AV2, the picture of
the external equipment will be output except during the DVD
playback of this unit. Turn off the external equipment or
press [DISPLAY] to output the picture of this unit.

Information on DV Dubbing

This function helps you to dub the contents in the DVC (digital
video camcorder) to HDD, DVD or VHS easily. (See page 75
for DVC to VHS Dubbing.)
You can control basic operations of the DVC from the remote
control of this unit if the DVC is in video mode.
Guide to DV and On-Screen Display
1
Connect your DVC to the DV input jack on the
front panel using a DV cable. (Use the DV cable
that has 4-pin input jack and is compliance with
the IEEE 1394 standards.)
2
Press [INPUT SELECT
the external input channel, then press
[PROG. ] repeatedly to select DV(AV3).
3
Press [DISPLAY] to display the DVC information
on the screen.
When the DVC is in video mode...
T 1/ 1 C 1/ 1
1
2
Control DVD
DV Audio Stereo1
Start Rec
3 4
When the DVC is in camera mode...
T 1/ 1 C 1/ 1
7
The menu changes according to the mode of DVC.
Switch the mode on the DVC to video mode for the dubbing
information.
] repeatedly to select
-RW VR ORG
DV
AB-1234
0:12:34
DVD SP 2:00
-RW VR ORG
5
DV
AB-1234
0:12:34
DVD SP 2:00
6
The following instructions are described with the
operations using the remote control of this unit.
1 DV icon
2 Indicator of active device
• With "Control" highlighted, press [ENTER OK] to display
the available devices to control with the remote control
of this unit. Select the device you want to operate using
[K L], then press [ENTER OK].
- Select "HDD" / "DVD" to control this unit with the remote
control of this unit.
- Select "DVC" to control your DVC with the remote
control of this unit.
3 Recording audio mode
• "DV Audio" can be changed. With "DV Audio" selected,
press [ENTER OK] to display "DV Audio" menu. Select
the audio you want to output using [K L], then press
[ENTER OK].
- Select "Stereo1" to dub the stereo sound.
- Select "Stereo2" to dub the sound that was added after
the recording.
- Select "Mix" to dub the stereo1 and stereo2.
4 Command menu
• "Start Rec" or "Pause Rec" will appear.
5 External input channel
6 Product name of your DVC
• If the unit cannot recognise the input signal from the
DVC or if it is the unknown product, "No Device" or "****"
will appear instead.
7 Status of the current operation and the time
counter
Each icon means (Available icons may vary depending on
the DVC):
DVC is in stop mode.
DVC is in playback mode.
DVC is in pause mode.
DVC is fast forwarding. (standard speed)
DVC is fast forwarding. (faster than above)
DVC is fast forwarding. (faster than above)
DVC is slow forwarding. (standard speed)
DVC is slow forwarding. (faster than above)
DVC is slow forwarding. (faster than above)
DVC is fast forwarding. (in stop mode)
DVC is fast reversing. (in stop mode)
DVC is fast reversing. (standard speed)
DVC is fast reversing. (faster than above)
DVC is fast reversing. (faster than above)
DVC is in slow reverse playback.
DVC is in recording.
DVC is in recording pause mode.
Please also read the operating instructions of your
DVC for more information.
39
EN