Center Focus; Virtual Rear Surround; Multi Rear Surround; Adjusting The Subwoofer Level - Panasonic SC-HT1500 Operating Instructions Manual

Center Focus

(Discs where the dialogue is recorded in the center channel)
You can make the sound of the center speaker seem
like it is coming from within the television.
Press [SHIFT]i[C.FOCUS].
Each time you do this:
!)
CENTER FOCUS ON CENTER FOCUS OFF
≥This will have less effect when Dolby Pro Logic II is
turned on.
≥This doesn't work when "SFC" is lit on the display.

Virtual Rear Surround

This mode is useful if you have to place your
surround speakers near the front speakers due
to the layout of your room.
This mode makes it seem like the sound from the
surround speakers is coming from behind you.
Press and hold [SHIFT]i[MULTI REAR] for
more than 5 seconds.
Each time you do this:
!)
V.R.S ON V.R.S OFF
This function works with:
–multi-channel discs
–2-channel discs with Dolby Pro Logic II on

Multi Rear Surround

This mode makes it seem like sound is coming
from multiple rear surround speakers virtually
when connected with surround speakers.
Press [SHIFT]i[MULTI REAR].
Each time you do this:
!)
M.R.S ON M.R.S OFF
This function works with:
–multi-channel discs
–2-channel discs with Dolby Pro Logic II on

Adjusting the subwoofer level

Press [S W.LEVEL].
Each time you press the button:
SUB W 1>SUB W 2>SUB W 3>SUB W 4 (factory preset)
^-------------------------------------------------------------}
≥This doesn't work when "SFC" is lit on the display.

Seat position

Using this function makes you feel like you are sitting
in the ideal seating position (in the center of the circle
formed by the speakers), even if you cannot due to
the layout of your room.
1
CF
2
This function works with:
–multi-channel discs
–2-channel discs with Dolby Pro Logic II on
Virtual speakers
To cancel
Press [SHIFT]i[S.POSITION] again.
[Note]
≥This doesn't work when "SFC" is lit on the display.
≥While Virtual Rear Surround is on, the seat position is changed in
three horizontal steps.
V.REAR

Speaker level adjustments

Adjust the level of the speakers so they are the same apparent level
as the front speakers where you would normally be sitting and
listening. (L, R
Preparation
≥Dolby Digital and DTS: Turn off the other sound field systems.
≥Dolby Pro Logic II: Press [SHIFT]i[ÎPRO LOGIC II].
1 Press [SHIFT]r[TEST] to output a test signal.
Lch: Front left
Cch: Center
Rch: Front right
Virtual speakers RSch: Right surround
LSch: Left surround
2 Press [VOLUME r] or [s] to set the volume level normally
used for listening.
M.V.REAR
3 Press [3] (to increase) or [4] (to decrease).
L, R: ( below, Balance)
C, RS, LS:
To stop the test signal, press [SHIFT]i[TEST] again.
∫ To adjust speaker level during play
(This doesn't work when "SFC" is lit on the display.)
1 Press [SHIFT]i[CH SELECT] to select the speaker.
L R>Cch>RSch>LSch>SWch
^---------------------------------------------------}
SW: Subwoofer
≥You can only adjust SW if there is output from the subwoofer
channel.
2 Press [3] (to increase) or [4] (to decrease).
L, R: ( below, Balance)
C, RS, LS:
SW:
Balance
You can adjust the balance of the front speakers.
1 Press [SHIFT]i[TEST] to select "Lch" or "Rch".
Or
Press [SHIFT]i[CH SELECT] to select "L R".
2 Press [2, 1] to adjust the "L", "R" balance.
Press [SHIFT]i[S.POSITION].
While "ON" is displayed
Press [3, 4, 2, 1] to select a position.
below, Balance)
j6 dB to i6 dB
j6 dB to i6 dB
j6 dB to i6 dB
RQT7621
47