Panasonic SC-HT1500 Operating Instructions Manual page 16

5
STEP Channel reception settings
Í/I
CHX, CHW
RDS TIME SLIP CH
PULL-OPEN
Í
Numbered
buttons
¢ CANCEL
3 4 2 1
ENTER
Preparation
≥Confirm that the aerial is connected correctly.
≥Switch [HOME THEATER, TV] to "HOME THEATER".
Auto-Setup
(Setup without Q Link functions)
≥When connecting to a television with the VIDEO OUT,
S-VIDEO OUT or COMPONENT VIDEO OUT terminal
( page 13).
≥When connecting to a television that does not have
the Q Link function ( page 55).
This unit's Auto-Setup function automatically tunes all available TV
stations and synchronizes the time and date with that of the
receiving station after tuning is completed.
≥When connecting to a television with RF socket only
( page 12)
1
Turn on the television and select the
appropriate AV input to suit the
connections to this unit.
2
Press [Í] to turn the unit on.
Auto-Setup starts. This takes about 5 minutes.
Auto-Setup
Ch
Auto-Setup in progress, please wait.
RETURN: to abort
RETURN
RQT7621
16
REC OPEN/CLOSE
TUNE
CH INPUT SELECTOR
HDD DVD FM/AM AUX
HOME
HOME THEATER TV
THEATER,
DISPLAY
TV
DIRECT TV REC AV
HDD DVD FM/AM AUX
1 2 3
W X CH
CH
4 5 6
VOLUME
7 8 9
CANCEL
HDD/DVD INPUT
0
-/--
SKIP SLOW/SEARCH
STOP PAUSE PLAY/
FUNCTIONS
DIRECT NAVIGATOR
FUNCTIONS
TOP MENU
ENTER
CH SELECT
FM MODE
RETURN
SUB MENU
RETURN
MIX
AV2/OPT
2CH
TEST PRO LOGIC
PROG/CHECK PROG/CHECK STATUS MANUAL SKIP VIDEO Plus +
VIDEO Plusr
TIME SLIP TIMER ERASE REC
F
MULTI REAR S.POSITION C.FOCUS
EXT LINK
DUBBING CREATE CHAP REC MODE
A B C D
AUDIO REPEAT
EQ/SFC
SHIFT SHIFT MUTING
S W. LEVEL
1
(When connecting to a television with RF socket only)
Set the new RF output channel to TV (refer to the
instructions for your TV).
Select an unused channel pre-set on your TV and tune it to
the RF output channel number shown on the unit's display.
(When the Auto-Setup screen does not appear clearly even
VOLUME
after performing the above operations, re-tune the channel
until the Auto-Setup screen becomes clear.)
DOWN UP
3
When Auto-Setup has been completed, the Owner ID
settings screen appears.
Press [1] and press the numbered
buttons to enter a 4-digit PIN number.
≥Make a note of the PIN number (don't forget), as it is not
possible to return to the factory preset.
4
Press [ENTER] twice to store the PIN
number.
The cursor moves to "Name".
5
Press [1].
6
Press [3, 4] to select a letter and
then press [1].
Repeat this to enter the name.
7
Press [ENTER] to store the name.
8
Press [4] and [1], and then repeat
steps 6, 7 to enter and store "House
No." and "Postcode".
9
Press [RETURN].
The Owner ID settings screen disappears.
To stop partway
Press [RETURN].
∫ If the clock setting menu appears
Set the clock manually ( page 52).
∫ To confirm that stations have been tuned
correctly ( page 51)
∫ To restart Auto-Setup ( page 51)
You can also use the following method to restart Auto-Setup.
When the unit is on and stopped
Press and hold [X CH] and [CH W] on the main unit for about 5
seconds.
≥All the settings except for the ratings level, ratings password,
Owner ID and time settings return to the factory preset. The timer
recording programmes are also cancelled.
[When connecting to a television with RF socket only ( page 12)]
∫ To enter the satellite station's name ( page 51)
The name of the satellite station is not set automatically. ("-- ---" will
appear under "Name" in the program list). After Auto-Setup is
completed, enter the name manually.
∫ If you connect other equipment to AV2 terminal
of this unit
Change the "AV2 Input" and "AV2 Connection" in the SETUP menu
to match the connected equipment ( page 50).
Owner ID
¢¢¢¢
PIN number
Name
House No.
Postcode
RETURN
RETURN : leave