Table of Contents
Advertisement
Others
Indications
Various functions and the Movie Camera status
are shown on the screen.
r:
Remaining Battery Power
≥As the remaining battery power decreases, the
indication changes as follows:
r > s > t > u > v
(When you are using the AC Adaptor, the
[s] Indication may appear, however, this
is not a malfunction.)
R 0:45:
Remaining Tape Time
≥Remaining tape time is indicated in minutes.
(When it reaches less than 2 minutes, the
indication starts flashing.)
230:
Tape Length
SP:
Standard Mode (Recording
Speed Mode)
LP:
Long Play Mode (Recording
Speed Mode)
REC:
Recording
PAUSE:
Recording Pause
CHK:
Recording Check
AUTO:
Automatic Mode
MNL:
Manual Mode
5k:
Zoom Magnification Indication
-42-
[:
Super Image Stabilizer
5:
Sports Mode (Programme AE)
-43-
7:
Portrait Mode (Programme AE)
-43-
4:
Low Light Mode (Programme
AE)
-43-
Ω:
Spotlight Mode (Programme
AE)
-43-
º:
Surf & Snow Mode (Programme
AE)
-43-
:
Sunset Mode (Programme AE)
-43-
1:
Manual White Balance Mode
-44-
MF:
Manual Focus
EXP:
Manual Iris
D.ZOOM:
Digital Zoom Mode
B/W:
Black & White Mode
SEPIA:
Sepia Mode
MOSAIC:
Mosaic Mode
NEGA:
Negative Mode
SOLARI:
Solarisation Mode
STRETCH:
Stretch Mode
RED FILTER: Red Mode
BLUE FILTER: Blue Mode
INT.REC:
Interval Recording Mode
Motion Sensor Stand-by Mode
STDBY:
-47-
0 Lux Night View Mode
0LUX:
!:
Playback
-49-
Forward Camera Search
;:
Still Playback
%:
Fast-forward
&:
Rewind
-49-
VOLUME:
Volume adjustment
TBC:
Time Base Corrector
TRACK.:
Tracking Adjustment Mode
A.DUB:
Audio Dubbing
INSERT:
Insert Editing Mode
Others
-36-
-40-
-40-
-41-
-41-
-41-
-41-
,
-44-
-45-
-42-
-45-
-45-
-46-
-45-
-45-
-45-
-45-
-45-
-45-
-45-
-45-
-47-
-48-
-41-
-50-
-49-
-49-
-50-
-52-
-52-
-54 -
To Use the Tape Counter Indication
The Tape Counter Indication is convenient for
the following 2 purposes: to check the Elapsed
Tape Time, and to use the Memory Stop
Function.
ª To check the Elapsed Tape Time
The Tape Counter Indication shows the elapsed
tape time both during recording and playback.
You can freely reset this indication (return the
counter to [0:00:00]). Therefore, by resetting the
counter to zero when you start recording or
playback, you can check the tape time that has
elapsed from that point.
1
Set [CAMERA FUNCTIONS] or
[VCR FUNCTIONS] >> [DISPLAY SETUP]
>> [DISPLAY] >> [ALL].
2
Continuing the aforesaid setup, select
[COUNTER RESET] >> [YES].
≥When recording or playback starts, the
elapsed tape time is indicated in hours,
minutes and seconds. During playback of
parts of the tape on which no recording has
been made, this indication does not change.
≥If you rewind the tape further than the tape
counter position [0:00:00], the minus sign [s]
appears in front of the Tape Counter
Indication.
ª To Change the Display Mode
By changing [DISPLAY] on the
[DISPLAY SETUP] Sub-Menu, you can change
the Display Mode to All Function Display [ALL],
Memory Stop Indication and Elapsed Tape Time
Indication Display [MEMORY], Partial Display
[PARTIAL] (Camera Mode only) and Minimum
Display [OFF]. With Partial Display and
Minimum Display, when you turn on the Movie
Camera, all indications appear for a few
seconds to inform you of the selected settings.
≥With Partial Display, if you switch the Movie
Camera over to the VCR Mode and then back
to the Camera Mode, [ALL] is automatically
selected for the Tape Counter Indication.
ª Memory Stop Function
This function is convenient for temporarily
marking a tape position during recording or
playback so that you can easily find it again later
for playback.
1
Reset the Tape Counter to zero at the tape
position from which you want to play it
back later. (
)
-39-
2
Set [CAMERA FUNCTIONS] or
[VCR FUNCTIONS] >> [DISPLAY SETUP]
>> [DISPLAY] >> [MEMORY].
3
Start recording or playback.
4
After recording or playback has finished,
set the [CAMERA/OFF/VCR] Switch to
[VCR].
≥The [VCR] Lamp lights up.
5
Fast-forward or rewind the tape.
≥The tape automatically stops approximately
at the position where the counter was set to
zero.
Hide quick links:
Advertisement
Table of Contents
