To Programme With The Showview Function - Panasonic NV-SJ410 Series Operating Instructions Manual

To Programme with the
ShowView Function
The ShowView numbers assigned to each TV programme
and published alongside the TV programme listings in
newspapers and magazines make it extremely easy to set the
VCR for timer recording.
The duration of a timer recording programmed with ShowView
number may be slightly longer than the actual duration of the
TV programme.
Preparations
≥ Confirm that the VCR is on.
≥ Confirm that the TV is on and the VCR viewing channel is
selected.
≥ Insert a video cassette with an intact erasure prevention
tab.
≥ Set the VCR/TV switch
Example:
Programming a timer recording of a TV programme with the
ShowView number 920126
Operations
1
Press the SHOW VIEW button
for entering the ShowView number on the TV.
2
Press the Numeric buttons
to enter the ShowView
number.
≥ If you have entered a wrong
digit, press the Cursor button
(2) and then enter the
correct digit.
3
Press the OK button
content.
4
Press the SP/LP button
speed.
≥ SP provides standard
recording time and
optimum picture quality.
LP provides doubled
recording time with slightly
reduced picture quality.
Regarding the "A" indication, refer to page 19.
≥ To extend the ending time or to make any corrections,
use the Cursor buttons (3421)
buttons , the DATE button
OFF button , the SP/LP button
≥ See page 19 for VPS/PDC recording.
5
Press the TAPE button
cassette tape length.
(See page 35.)
6
Press the OK button
settings.
≥ To programme additional
timer recordings, repeat
operation steps 1–6.
18
to "VCR".
to display the menu
On Screen Display
ShowView
9 2 0 1 2 6
to display the programmed
to set the desired tape
Timer recording
Pos Start Stop SP VPS
Name DATE ON OFF LP PDC Min
ZDF 27/10 We 20:00 21:30 SP ON
: :
jjjjj jj/jj jj jj jj jj jj jj
: :
jjjjj jj/jj jj jj jj jj jj jj
: :
jjjjj jj/jj jj jj jj jj jj jj
: :
jjjjj jj/jj jj jj jj jj jj jj
jjjjj jj jj jj jj jj jj jj jj
jjjjj jj jj jj jj jj jj jj jj
jjjjj jj jj jj jj jj jj jj jj
, the Channel
, the ON button
.
to select the corresponding
again to conclude the
Timer recording
Pos Start Stop SP VPS
Name DATE ON OFF LP PDC Min
ZDF 27/10 We 20:00 21:30 SP ON
: :
jjjjj jj/jj jj jj jj jj jj jj
: :
jjjjj jj/jj jj jj jj jj jj jj
: :
jjjjj jj/jj jj jj jj jj jj jj
jjjjj jj jj jj jj jj jj jj jj
jjjjj jj jj jj jj jj jj jj jj
jjjjj jj jj jj jj jj jj jj jj
jjjjj jj jj jj jj jj jj jj jj
7
Press the TIMER REC button
over to the timer recording standby mode.
≥ Check that "Á" is lit on the VCR display.
If it is flashing, check the timer recording details again.
(See page 20.)
If "– –" Appears under "Pos/Name" after
Entering a ShowView Number
Pos/Name stands for Programme Position/TV Station Name.
Normally, the name of the TV station or the number of the
programme position is displayed under "Pos/Name".
However, if the TV station information was not automatically
set during Preset Download or Auto Setup due to adverse
reception conditions, the "– –" indication appears instead.
In such a case, follow the operation steps below to correct it.
Press the Channel buttons
repeatedly to select the programme
position on which the TV programme
to be recorded will be broadcast.
After you have entered the information of a TV station, it
remains stored in the VCR's memory, and you do not need to
enter it again in the future.
To Suspend the Timer Recording Standby
Mode
When you want to use the VCR for playback, normal
recording or some other operation before the programmed
timer recording will be performed, you can temporarily
suspend the timer recording standby mode by
pressing the TIMER REC button
on the VCR display disappears.
However, after you have finished using the VCR, be sure
90
to reactivate the timer recording standby mode by pressing
jjj jjj
jjj jjj
the TIMER REC button
jjj jjj
jjj jjj
jjj jjj
timer recording will not be performed.
jjj jjj
jjj jjj
, the
Note:
≥ If the VCR is not put in the timer recording standby mode at
the latest 10 minutes before the programmed timer
recording starting time, the "Á" indication flashes on the
VCR display. In this case, press the TIMER REC button
to put the VCR in the timer recording standby mode.
90
jjj jjj
jjj jjj
jjj jjj
jjj jjj
jjj jjj
jjj jjj
jjj jjj
to switch the VCR
Timer recording
Pos Start Stop SP VPS
Name DATE ON OFF LP PDC Min
: :
15 00 17 00
jj jjjjj
: :
jjjjj jj/jj jj jj jj jj jj
: :
jjjjj jj/jj jj jj jj jj jj
jjjjj jj jj jj jj jj jj jj
jjjjj jj jj jj jj jj jj jj
"– –" indication
jjjjj jj jj jj jj jj jj jj
jjjjj jj jj jj jj jj jj jj
jjjjj jj jj jj jj jj jj jj
so that the "Á" indication
again, otherwise the programmed
SP ppp 120
jj jjj jjj
jj jjj jjj
jj jjj jjj
jj jjj jjj
jj jjj jjj
jj jjj jjj
jj jjj jjj