To Programme With The Showview Function - Panasonic NV-SJ412EE Operating Instructions Manual

To Programme with the
ShowView Function
The ShowView numbers assigned to each TV programme
and published alongside the TV programme listings in
newspapers and magazines make it extremely easy to set the
VCR for timer recording.
The duration of a timer recording programmed with
ShowView number may be slightly longer than the actual
duration of the TV programme.
Preparations
≥ Confirm that the VCR is on.
≥ Confirm that the TV is on and the VCR viewing channel is
selected.
≥ Insert a video cassette with an intact erasure prevention
tab.
≥ Set the VCR/TV switch
Example:
Programming a timer recording of a TV programme with the
ShowView number 920126
Operations
1
Press the SHOW VIEW button
for entering the ShowView number on the TV.
2
Press the Numeric buttons
to enter the ShowView
number.
≥ If you have entered a wrong
digit, press the Cursor button
(2) and then enter the
correct digit.
3
Press the OK button
content.
4
Press the SP/LP button
speed.
≥ SP provides standard
recording time and
optimum picture quality.
LP provides doubled
recording time with slightly
reduced picture quality.
Regarding the "A" indication, refer to page 19.
≥ To extend the ending time or to make any corrections,
use the Cursor buttons (3421)
button , the DATE button
OFF button , the SP/LP button
≥ See page 19 for VPS/PDC recording.
5
Press the TAPE button
corresponding cassette tape length.
(See page 35.)
6
Press the OK button
settings.
≥ To programme additional
timer recordings, repeat
operation steps 1 –6.
18
to "VCR".
to display the menu
On Screen Display
ShowView
9 2 0 1 2 6
to display the programmed
to set the desired tape
Timer recording
Pos Start Stop SP VPS
Name DATE ON OFF LP PDC Min
ZDF 27/10 We 20:00 21:30 SP OFF
: :
jjjjj jj/jj jj jj jj jj jj jj
: :
jjjjj jj/jj jj jj jj jj jj jj
: :
jjjjj jj/jj jj jj jj jj jj jj
: :
jjjjj jj/jj jj jj jj jj jj jj
jjjjj jj jj jj jj jj jj jj jj
jjjjj jj jj jj jj jj jj jj jj
jjjjj jj jj jj jj jj jj jj jj
, the Channel
, the ON button
.
to select the
again to conclude the
Timer recording
Pos Start Stop SP VPS
Name DATE ON OFF LP PDC Min
ZDF 27/10 We 20:00 21:30 SP OFF
: :
jjjjj jj/jj jj jj jj jj jj jj
: :
jjjjj jj/jj jj jj jj jj jj jj
: :
jjjjj jj/jj jj jj jj jj jj jj
jjjjj jj jj jj jj jj jj jj jj
jjjjj jj jj jj jj jj jj jj jj
jjjjj jj jj jj jj jj jj jj jj
jjjjj jj jj jj jj jj jj jj jj
7
Press the TIMER REC button
over to the timer recording standby mode.
≥ Check that "Á" is lit on the VCR display.
If it is flashing, check the timer recording details again.
(See page 20.)
If "– –" Appears under "Pos/Name" after
Entering a ShowView Number
Pos/Name stands for Programme Position/TV Station Name.
Normally, the name of the TV station or the number of the
programme position is displayed under "Pos/Name".
However, if the TV station information was not automatically
set during Download or Auto Setup due to adverse reception
conditions, the "– –" indication
appears instead.
In such a case, follow the operation
steps below to correct it.
Press the Channel button
programme position on which the TV programme
to be recorded will be broadcast.
After you have entered the information of a TV station, it
remains stored in the VCR's memory, and you do not need
to enter it again in the future.
If "Pos/Name" (Programme Position) Is Not
Entered Correctly When Programming with
the ShowView Function
See steps 1–3 on page 30.
14 Press the Cursor buttons (3421)
station which you want to delete.
15 Press the Channel button (J, red)
to delete the incorrect programme position (Delete).
16 Press the Date button (r, green)
to insert a blank programme position (Add).
17 Press the OK button
menu.
18 Press the Numeric buttons
number of the desired TV station and press the OK
button .
90
19 Press the Cursor buttons (3421)
jjj jjj
jjj jjj
jjj jjj
entry field for "Name".
jjj jjj
jjj jjj
jjj jjj
10 Use the Cursor buttons (3421)
jjj jjj
to enter the station name.
≥ If the station name needs a blank space, select the
blank between "Z" and "¢".
11 Press the OK button
, the 12 Press the EXIT button
13 Perform the operation of the ShowView function.
To Suspend the Timer Recording Standby
Mode
See page 17.
Note:
≥ If the VCR is not put in the timer recording standby mode at
the latest 10 minutes before the programmed timer
recording starting time, the "Á" indication flashes on the
VCR display. In this case, press the TIMER REC button
90
jjj jjj
to put the VCR in the timer recording standby mode.
jjj jjj
jjj jjj
jjj jjj
jjj jjj
jjj jjj
jjj jjj
to switch the VCR
Timer recording
Pos Start Stop SP VPS
Name DATE ON OFF LP PDC Min
: :
15 00 17 00 SP
jj jjjjj
: :
jjjjj jj/jj jj jj jj jj jj jj
: :
jjjjj jj/jj jj jj jj jj jj jj
jjjjj jj jj jj jj jj jj jj jj
"– –" indication
jjjjj jj jj jj jj jj jj jj jj
jjjjj jj jj jj jj jj jj jj jj
jjjjj jj jj jj jj jj jj jj jj
jjjjj jj jj jj jj jj jj jj jj
repeatedly to select the
to select the TV
and the OK button
and the OK button
to display the Manual Tuning
to enter the channel
to select the
and the OK button
to conclude the setting.
to exit the On Screen Display.
ppp 120
jjj jjj
jjj jjj
jjj jjj
jjj jjj
jjj jjj
jjj jjj
jjj jjj