To Programme With The Showview Function - Panasonic NV-HS960EE Operating Instructions Manual

To Programme with the
ShowView Function
The ShowView numbers assigned to each TV programme
and published alongside the TV programme listings in
newspapers and magazines make it extremely easy to set the
VCR for timer recording.
The duration of a timer recording programmed with
ShowView number may be slightly longer than the actual
duration of the TV programme.
Preparations
≥ Confirm that the VCR is on.
≥ Confirm that the TV is on and the VCR viewing channel is
selected.
≥ Insert a video cassette with an intact erasure prevention
tab.
As soon as the cassette is inserted, the Cassette Number
Check starts. Wait a few moments until it is completed.
(See page 16.)
≥ Set the VCR/TV switch
Example:
Programming a timer recording of a TV programme with the
ShowView number 920126
Operations
1
Press the SHOW VIEW button
menu for entering the ShowView number on the TV.
2
Press the Numeric buttons
ShowView number.
≥ If you have entered a
wrong digit, press the
Cursor button (2)
and then enter the
correct digit.
3
Press the OK button
content.
4
Press the SP/LP button
speed.
≥ SP provides standard
recording time and optimum
picture quality.
LP provides doubled
recording time with slightly reduced picture quality.
EP provides triple recording time with slightly
reduced picture quality.
Regarding the "A" indication, refer to page 25.
≥ To extend the ending time or to make any
corrections, use the Cursor buttons (3421)
the Channel button
button , the OFF button
≥ See page 25 for VPS/PDC recording.
5
Press the TAPE button
corresponding cassette tape length.
≥ The tape length is displayed on the VCR display.
6
Press the OK button
settings.
≥ To programme additional
timer recordings, repeat
operation steps 1–6.
24
to "VCR".
to display the
to enter the
On Screen Display
ShowView
9 2 0 1 2 6
to display the programmed
to set the desired tape
Timer recording
Pos Start Stop SP VPS
Name DATE ON OFF LP PDC Min
ZDF 27/10 We 20:00 21:30 SP OFF
: :
jjjjj jj/jj jj jj jj jj jj jj
: :
jjjjj jj/jj jj jj jj jj jj jj
: :
jjjjj jj/jj jj jj jj jj jj jj
: :
jjjjj jj/jj jj jj jj jj jj jj
jjjjj jj jj jj jj jj jj jj jj
jjjjj jj jj jj jj jj jj jj jj
jjjjj jj jj jj jj jj jj jj jj
, the DATE button , the ON
, the SP/LP button
to select the
again to conclude the
Timer recording
Pos Start Stop SP VPS
Name DATE ON OFF LP PDC Min
ZDF 27/10 We 20:00 21:30 SP OFF
: :
jjjjj jj/jj jj jj jj jj jj jj
: :
jjjjj jj/jj jj jj jj jj jj jj
: :
jjjjj jj/jj jj jj jj jj jj jj
jjjjj jj jj jj jj jj jj jj jj
jjjjj jj jj jj jj jj jj jj jj
jjjjj jj jj jj jj jj jj jj jj
jjjjj jj jj jj jj jj jj jj jj
7
Press the TIMER REC button
over to the timer recording standby mode.
≥ Check that "Á" is lit on the VCR display.
If it is flashing, check the timer recording details
again. (See page 26.)
If "– –" Appears under "Pos/Name" after
Entering a ShowView Number
Pos/Name stands for Programme Position/TV Station
Name.
Normally, the name of the TV station or the number of the
programme position is displayed under "Pos/Name".
However, if the TV station information was not
automatically set during Download
or Auto Setup due to adverse
reception conditions, the "– –"
indication appears instead.
In such a case, follow the
operation steps below to correct it.
Press the Channel button
programme position on which the TV programme to be
recorded will be broadcast.
After you have entered the information of a TV station, it
remains stored in the VCR's memory, and you do not need
to enter it again in the future.
If "Pos/Name" (Programme Position) Is Not
Entered Correctly When Programming with
the ShowView Function
See steps 1 –3 on page 46.
14 Press the Cursor buttons (3421)
station which you want to delete.
15 Press the Channel button (J, red)
to delete the incorrect programme position (Delete).
16 Press the DATE button (i, green)
to insert a blank programme position (Add).
17 Press the OK button
menu.
18 Press the Numeric buttons
number of the desired TV station and press the
90
jjj jjj OK button
jjj jjj
jjj jjj
19 Press the Cursor buttons (3421)
jjj jjj
jjj jjj
jjj jjj
entry field for "Name".
jjj jjj
10 Use the Cursor buttons (3421)
to enter the station name.
≥ If the station name needs a blank space, select the
blank between "Z" and "¢".
11 Press the EXIT button
,
12 Perform the operation of the ShowView function.
.
To Suspend the Timer Recording Standby
Mode
See page 23.
Note:
≥ If the VCR is not put in the timer recording standby mode at
the latest 10 minutes before the programmed timer
recording starting time, the "Á" indication flashes on the
VCR display. In this case, press the TIMER REC button
to put the VCR in the timer recording standby mode.
90
jjj jjj
jjj jjj
jjj jjj
jjj jjj
jjj jjj
jjj jjj
jjj jjj
to switch the VCR
Timer recording
Pos
Name DATE
jj jjjjj
jjjjj jj/jj jj jj
jjjjj jj/jj jj jj
jjjjj jj/jj jj jj
jjjjj jj/jj jj jj
jjjjj jj/jj jj jj
jjjjj jj jj jj jj jj jj jj jj
jjjjj jj jj jj jj jj jj jj jj
"– –" indication
repeatedly to select the
and the OK button
and the OK button
to display the Manual Tuning
to enter the channel
.
and the OK button
to exit the On Screen Display.
Start Stop SP VPS
ON OFF LP PDC Min
15:00 17:00 SP 120
jjj
: :
jj jj jj jj jjj jjj
: :
jj jj jj jj jjj jjj
: :
jj jj jj jj jjj jjj
: :
jj jj jj jj jjj jjj
: :
jj jj jj jj jjj jjj
jjj jjj
jjj jjj
to select the TV
to select the