One Touch Recording; Direct Tv Recording; Ext Link - Panasonic DMR-E100H Operating Instructions Manual

∫ Recording
DVD
VIDEO Plus+ DIRECT TV REC
SKIP
DIRECT TV REC
1
STOP
∫
4
DIRECT NAVIGATOR
TOP MENU
3, 4, 2, 1
ENTER
FUNCTIONS
FUNCTIONS
FRAME
PROG/CHECK TIMER
STATUS MARKER
STATUS
POSITION
DISPLAY
MEMORY
A

One Touch Recording

[HDD] [RAM] [DVD-R]
Main unit only
This is a simple way to make timer recordings when you are in a
hurry or before you go to bed. You can set the time up to 4 hours in
advance.
While recording
Press [¥, REC] on the main unit to select
the recording time.
The time increases as illustrated by each press of the button.
The counter decreases in 1-minute units after you set a time. You
can change the time again with the same operation.
When the time you set is reached, recording stops and the unit
switches to standby.
Unit's Display
(Counter) # 30 # 60 # 90
^ 240 ! 180 ! 120 !}
ªTo cancel
During recording, press [¥, REC] until the counter appears.
≥Recording continues.
ªTo show the time remaining until
recording finishes
Press [STATUS] several times.
≥It is displayed in the unit of minute.
For your reference
≥This does not work during timer recordings or flexible recording.
≥Recording stops and the set time is cleared if you press
[∫, STOP].
≥The set time is cleared if you change the recording mode or
channel while recording is paused.
DVD TV
DVD
TV
HDD
DVD
HDD DVD
INPUT SELECT AV
SLOW/SEARCH
2 3
PAUSE PLAY/x1.3
CH
6
5
PLAY LIST
MENU
ENTER
RETURN
RETURN
MANUAL SKIP TIME SLIP
ERASE REC
DUBBING REC MODE
AUDIO
B C D
DVD-RAM
REC/OTR 30
ARD
L R

Direct TV Recording

This function allows you to immediately start recording the same
programme that you are viewing on the TV.
The programme position selected on the unit automatically
changes to that of the TV programme that you are viewing on the
TV.
Conditions for the Direct TV Recording function:
≥Your TV must be equipped with the [Q Link] function.
≥The unit must be connected to the TV via a fully-wired 21-pin
Scart cable.
[1] Press [HDD] or [DVD] to select the
recording drive.
[2]
When DVD mode was selected above:
Insert a disc.
(page 19)
[3] Press [DIRECT TV REC].
≥Recording of the TV programme that you are viewing on the
TV starts.
[4] Press [∫, STOP] to stop recording.
Note
≥When you stop recording, the unit automatically switches back to
the previously selected programme position.

EXT LINK

[HDD] [RAM] [DVD-R]
If an external equipment (e.g., a satellite receiver) with a timer
function is connected to the AV2 socket of this unit by a 21-pin
cable, it is possible to control the recording of the unit with the
equipment. For the connection to the external equipment, see
page 57.
Preparation
≥Make sure that "AV2 Connection" is set to "Ext Link 1" or
"Ext Link 2". (page 61)
≥Timer programming has to be done on the external equipment
and switch to the timer recording standby mode. Refer to the
equipment's operating instructions.
1) Press [EXT LINK] on the unit to switch the unit over to the timer
recording standby mode.
≥As long as a video
picture is being
transmitted by the
Satellite or Digital
Receiver, the unit
will record it.
The notice is
displayed on the
TV screen.
(Only when [Ext Link 2] is selected)
To delete it, press [ENTER].
2) To cancel the external control, turn off the timer recording
standby mode of the unit by pressing [EXT LINK] again.
For your reference
≥To switch TV automatically to the picture from the unit in
playback mode, connect the AV1 socket of this unit to the TV by
a 21-pin cable.
≥This function does not work with some equipment. Refer to the
equipment's operating instructions.
≥The beginning of recordings may not be recorded correctly in
some cases.
≥When "AV2 Connection" is set to "Ext Link 2", this function does
not work if the input signal is NTSC system.
≥The play picture or menu picture is not output from AV2 socket
during Linked timer recording standby mode.
28
(page 19)
DVD now recording this programme.
Yes Cancel