Related Manuals for Bernee BN-5606XAT1
Summary of Contents for Bernee BN-5606XAT1
-
Page 1: User Manual
Bernee Auto Tracking Dome Camera User Manual Auto Tracking High Speed Dome Camera User Manual 1 / 39... -
Page 2: Table Of Contents
Bernee Auto Tracking Dome Camera User Manual Contents SECTION1 INSTRUCTION ............................ 3 ............................ 3 RODUCTION NTRODUCING .................................. 3 HARACTER .............................. 3 UNCTION ESCRIPTION .......................... 7 PECIFICATION OMPARISON HART SECTION 2 NORMAL OPERATION ........................ 10 ... -
Page 3: Section1 Instruction
Bernee Auto Tracking Dome Camera User Manual Section1 Instruction 1.1 Production Introducing The dome cameras feature high position resolution, high speed, low price and selectable communication protocols; widely used in surveillance system. 1.2 Character Built-in English OSD Menu, by which you can change dome parameter, set or call preset, and achieve auto tour, pattern, auto scan etc. - Page 4 Bernee Auto Tracking Dome Camera User Manual only react the controlling command in accordance with its own Address, Baud-rate and Protocol. (2) Object tracking The dome can be manually controlled from the control system by using the joystick on the controller to move the camera up and down, right and left to follow objects under observation.
- Page 5 Bernee Auto Tracking Dome Camera User Manual The camera will not auto focus in the following status. Target is not in the center of image. Targets are in near and far at the same time. Target is of strong light object. Such as spotlight etc.
- Page 6 Bernee Auto Tracking Dome Camera User Manual A pattern is a saved moving course; the camera will repeat its pan, tilt, zoom and preset functions that can be recalled with a command from a controller or automatically by a programmed function (alarm, park or power-up).
-
Page 7: Specification Comparison Chart
Bernee Auto Tracking Dome Camera User Manual 1.4 Specification Comparison Chart Models BN-5606XAT1 BN-5606XAT3 BN-5606EAT1 BN-5606EAT3 Appearance Installation Indoor/Embedded Outdoor/ Wall Indoor/Embedded Outdoor/ Wall mount mount Auto Track Image Sensor 1/4″ Ex-view HAD color CCD Effective Pixel 752(H)×582(V) Horizontal 480TV Lines... - Page 8 Bernee Auto Tracking Dome Camera User Manual Electronic 1/1~1/10, 000 seconds, 22 speed-levels Shutter External VISCA(TTL signal power level), baud rate: 9.64Kb/s,19.24Kb/s,38.4Kb/s, stop position Control 1 or 2 optional Privacy Mask On/Off (24 zones) ON / OFF (8 zones) Picture Feature Electronic flip, backward flip, black & white, mirror...
- Page 9 Bernee Auto Tracking Dome Camera User Manual Relative 5%～90% Humidity 9 / 39...
-
Page 10: Section 2 Normal Operation
Bernee Auto Tracking Dome Camera User Manual Section 2 Normal Operation These operating instructions cover the basic operation of the dome and its features. When the dome is used with other manufacturers’ control system, please refer to the system controller’s instructions. - Page 11 Bernee Auto Tracking Dome Camera User Manual Address … … … … … … … … … Finishing dial-up switchers, please insert dome engine into metal shell Precaution: 1. when inserting engine, we must ensure engine accordant with square slot inside shell, and then fix clips of both sides.
- Page 12 Bernee Auto Tracking Dome Camera User Manual After powered up, the dome will conduct reset procedure. In this procedure, the dome firstly pans to the default horizontal origin point, and finally tilts to the vertical 45° position to complete the self-testing.
-
Page 13: Section 3 Menu Configuration
Bernee Auto Tracking Dome Camera User Manual Section 3 Menu Configuration You need to install the dome system before using this manual. Please refer to the installation packet supplied with the back box for installation instructions. After installed properly, power up the camera. It will start a configuration sequence. After the configuration is done, the monitor will display as below. -
Page 14: Select Language
Bernee Auto Tracking Dome Camera User Manual 3.2 Select Language The language for the on-screen menus is selectable. Available languages include English and Chinese. The factory default language is English. Changing the display language: (1) In main menu move the joystick to position the cursor beside LANGUAGE. -
Page 15: Label Position
Bernee Auto Tracking Dome Camera User Manual DISPLAY SETUP PRESET LABEL ZONE LABEL ZOOM AZIMUTH/ELEVATION CAMERA LABEL <LABEL POSITION> BACK EXIT Figure 3.3 DISPLAY SETUP Display setup enables you to program how labels are displayed on the monitor. The following labels are available: PRESET LABEL: Identifying preset. -
Page 16: Dome Settings1
Bernee Auto Tracking Dome Camera User Manual (1) Move joystick to position the cursor beside a label. (2) Press iris Open. (3) Move joystick to move the label up, down, left, or right. (4) Press iris Open. (5) Repeat steps 1 through 4 to position other labels. - Page 17 Bernee Auto Tracking Dome Camera User Manual BACKLIGHT COMPENSATION(BLC): If a bright backlight presents, the subjects in the picture may appear dark or as a silhouette. Backlight compensation enhances objects in the center of the picture. The dome uses the center of the picture to adjust the iris.
- Page 18 Bernee Auto Tracking Dome Camera User Manual Low light limit is the maximum duration, it is in fractions of a second, that electronic shutter will remain open in low light conditions. The default setting is 1/50. Settings include:1/2, 1/3, 1/6, 1/12, 1/25, 1/50, 1/75, 1/100, 1/120, 1/150, 1/215, 1/300, 1/425, 1/600, 1/1000, 1/1250, 1/1750, 1/2500, 1/3500, 1/6500, 1/10000.
- Page 19 Bernee Auto Tracking Dome Camera User Manual Iris level is the lens function that automatically opens and closes the iris in response to changing light conditions. The default setting is F1.6. Settings include: F1.6, F2.2, F3.2, F4.4, F6.4, F8.8, F12, F17, F24, F34.
-
Page 20: Motion Setting
Bernee Auto Tracking Dome Camera User Manual AUTO IRIS: Auto iris is the lens function that automatically opens and closes the iris in response to changing light conditions. Program the auto iris to operate automatically or at a user-defined level. - Page 21 Bernee Auto Tracking Dome Camera User Manual FIGURE 3.9 MOTION MENU AUTO FILP: When the dome camera tilts downward and goes just beyond the vertical, the dome camera rotates 180 degrees automatically. Afterwards, the dome camera starts moving upward even you still hold joystick in the down position.
- Page 22 Bernee Auto Tracking Dome Camera User Manual PANTTERN 1: Dome runs pattern1. PANTTERN 2: Dome runs pattern2. PANTTERN 3: Dome runs pattern3. PANTTERN4: Dome runs pattern4. SCAN SPEED: Scan speed is that the dome will pan when in a FRAME SCAN mode. Scan speed is adjustable from 1 to 32 via the programming menu.
-
Page 23: Power Up
Bernee Auto Tracking Dome Camera User Manual To program azimuth zero: (1) Move joystick to position the cursor beside set azimuth zero. (2) Press iris Open. (3) Follow the directions displayed on the monitor. CLEAR AZIMUTH ZERO: (1) Move joystick to position the cursor beside CLEAR AZIMUTH ZERO. -
Page 24: Presets Setting
Bernee Auto Tracking Dome Camera User Manual 3.5.5 Presets Setting Move joystick to select <PRESETS>, press Open to enter the presets menu shown as Fig3.11. PRESETS PRESET NUMBER …PRESET NOT DEFINEO… < EDIT PRESET LABEL > < EDIT PRESET SCAENE >... -
Page 25: Patterns Setting
Bernee Auto Tracking Dome Camera User Manual e. After the label is inputted, move the cursor to CE, then press iris Open to cancel and return to the Preset menu. (3) Edit preset scene a. Move joystick to position the cursor beside EDIT PRESET SCENE. -
Page 26: Zone Setting
Bernee Auto Tracking Dome Camera User Manual (1) Move joystick to position the cursor beside CLEAR PATTERN. (2). Press iris Open. (3) F0llow the directions displayed on the monitor. 3.5.7 Zone Setting Move joystick to select <ZONES>, then press Open to enter the zones menu shown as Fig 3.14. -
Page 27: Clears Setting
Bernee Auto Tracking Dome Camera User Manual ZONE NUMBER ZONE LABLE 1 - - - - - 0 1 2 3 4 5 6 7 8 9 Y Z y z A B C D E F G H I J K L M N O P Q R S T U V W X... -
Page 28: Presets Number
Bernee Auto Tracking Dome Camera User Manual Clear all presets. To clear a specific preset, please refer to the PRESETS section. CLEAR PATTERNS: Clear all patterns. To clear a specific pattern, please refer to the PATTERNS section. RESTORE FACTORY DEFAULTS: This is to restore leaving-factory’s default settings. -
Page 29: Alarms Setting
Bernee Auto Tracking Dome Camera User Manual There are three alarm settings: ALARM NUMBER: Use this to select alarms number. SEQUENCE<SECS>: This is the time the dome will perform an alarm activity when more than one alarm of the same priority occurs at the same time. - Page 30 Bernee Auto Tracking Dome Camera User Manual (1) Move joystick to position the cursor beside Alarm action. (2) Press iris Open. (3) Move the joystick up or down to view the available selections. Below are the settings for alarm action: NONE: No action when alarm is triggered.
-
Page 31: Aux Setting
Bernee Auto Tracking Dome Camera User Manual (4) Press iris Open to confirm selection. 3.6.3 Aux Setting Move joystick to select <AUX>, then press Open to enter the aux menu shown as Fig 3.20. DWELL TIME<SECS> 1 DWELL TIME<SECS> 2... -
Page 32: Windows Blanking
Bernee Auto Tracking Dome Camera User Manual PLEASE INPUT OLD PASSWORED PASSWORD 1 2 3 4 5 6 7 8 9 0 CLEAR ENTER EXIT Figure 3.22 EDIT PASSWORD (1) Move joystick to position the cursor beside a number. Press iris Open to confirm selection. -
Page 33: Set Windows
Bernee Auto Tracking Dome Camera User Manual BLANK ALL ABOVE BLANK ALL BELOW No Blanking No Blanking -5º~10º 5º~92º -5º~25º -5º~92º 10 -5º~35º 5º~92º -5º~45º 15º~92º -5º~55º 25º~92º -5º~65º 35º~92º -5º~75º 45º~92º -5º~85º 55º~92º -5º~95º 70º~92º 3.6.6 Set Windows Move joystick to select <SET WINDOWS>, then press Open to enter the set windows menu shown as Fig 3.24. -
Page 34: Edit Windows Location
Bernee Auto Tracking Dome Camera User Manual 3.6.7 Edit Windows Location Move joystick and move cursor to < EDIT WINDOWS LOCATION >, then press open to enter the menu as Fig 3.25. EDIT WINDOWS LOCATION IRIS OPEN TO CONTINUE IRIS CLOSE TO CANCEL Figure 3.25 EDIT WINDOWS MENU... -
Page 35: Heater Setting
Bernee Auto Tracking Dome Camera User Manual Press Close to discard the setting and return to Fig 3.24 Press Open to save the setting and return to Fig 3.24. 3.6.9 Heater Setting From the dome setting 2 menus shown in Fig3.17, move joystick and move cursor to HEATER SETTING, press Open to enter the following menu (Figure 3.28). -
Page 36: Tracking Setting
Bernee Auto Tracking Dome Camera User Manual enter the following menu. CRUISE DWELL TIME<SECS> PRESET LIST 1 ON 0 OFF 1 2 3 4 5 6 7 8 9 0 0 1 1 0 0 1 0 1 1 1... -
Page 37: Tracking Boundary
Bernee Auto Tracking Dome Camera User Manual TRACKING SETTING DEFAULT SETTING SIZE SNS MIDIUM GRAY SNS MIDIUM LOST ACT TO HOME & TRACKING AUTO ZOOMING WAIT TINE<S> <TRACKING BOUNDARY> BACK EXIT Figure 3.30 TRACKING SETTING Default Setting: tracking setting to default. -
Page 38: Dome Label
Bernee Auto Tracking Dome Camera User Manual TRACKING BOUNDARY BOUNDARY LIMIT CLEAR BOUNDARY LEFT LIMIT RIGHT LIMIT UP LIMIT DOWN LIMIT BACK EXIT Figure 3.31 TRACKING BOUNDARY BOUNDAR LIMIT: enable / disable the boundary CLEAR BOUNDARY: clear setting of the current boundary... -
Page 39: Other Functions
Bernee Auto Tracking Dome Camera User Manual 3.8 Other Functions RESET CAMERA: If the camera does not operate or if you close camera’s control, cycle camera power. Cycling camera power resets the camera but does not change any saved camera settings.