Related Manuals for Epson S5U13719P00C100
Summary of Contents for Epson S5U13719P00C100
- Page 1 S1D13719 Mobile Graphics Engine S5U13719P00C100 Evaluation Board User Manual SEIKO EPSON CORPORATION Rev. 1.1...
- Page 2 This evaluation board/kit or development tool is intended for use by an electronics engineer and is not a consumer product. The user should use it properly and in a safe manner. Seiko Epson does not assume any responsibility or liability of any kind of damage and/or fire caused by the use of it.
-
Page 3: Table Of Contents
Chapter 6 Schematic Diagrams ......23 Chapter 7 S5U13719P00C100 Board Layout ..... . . 27 Chapter 8 References . - Page 4 EPSON S5U13719P00C100 Evaluation Board User Manual (Rev. 1.1)
-
Page 5: Chapter 1 Introduction
The S5U13719P00C100 evaluation board can connect to the S5U13U00P00C100 USB Adapter board so that it can be used with a laptop or desktop computer, via USB 2.0. The S5U13719P00C100 evaluation board can also be used with many other native platforms via the host connectors which provide the appropriate signals to support a variety of CPUs. -
Page 6: Chapter 2 Features
Chapter 2 Features Chapter 2 Features The S5U13719P00C100 Evaluation Board includes the following features: • 180-pin PFBGA S1D13719 Mobile Graphics Engine • Headers for connection to the S5U13U00P00C100 USB Adapter board • Headers for connecting to various Host Bus Interfaces •... -
Page 7: Chapter 3 Installation And Configuration
Chapter 3 Installation and Configuration Chapter 3 Installation and Configuration The S5U13719P00C100 evaluation board incorporates a DIP switch, jumpers, and 0 ohm resistors which allow it to be used with a variety of different configurations. 3.1 Configuration DIP Switch The S1D13719 has configuration inputs (CNF[7:0]) which are read on the rising edge of RESET#. An 8-position DIP switch (SW1) is used to configure the S1D13719 for multiple Host Bus Interfaces. -
Page 8: Configuration Jumpers
Camera1 power supply ON = Required settings when using S5U13U00P00C100 USB Adapter board (SW1-[8:1] = 000000x0b) 3.2 Configuration Jumpers The S5U13719P00C100 has 9 jumpers which configure various board settings. The jumper positions for each function are shown below. Jumper Function... - Page 9 The jumper associated to each power supply is as follows: JP1 for COREVDD JP2 for PLLVDD JP3 for HIOVDD JP4 for PIOVDD JP7 for CIO1VDD JP8 for CIO2VDD JP9 for SIOVDD Figure 3-2: Configuration Jumper Locations (JP1-JP4 and JP7-JP9) S5U13719P00C100 Evaluation Board User Manual (Rev. 1.1) EPSON...
- Page 10 When the jumper is at position 1-2, the HIOVDD voltage must be provided to the H1 connector, pin 32. When the jumper is at position 2-3, the HIOVDD voltage is provided by the 3.3V power supply of the board. Figure 3-3: Configuration Jumper Location (JP5) EPSON S5U13719P00C100 Evaluation Board User Manual (Rev. 1.1)
- Page 11 When the jumper is at position 1-2, the PIOVDD voltage must be provided to the H6 connector, pin 1. When the jumper is at position 2-3, the PIOVDD voltage is provided by the 3.3V power supply of the board. Figure 3-4: Configuration Jumper Location (JP6) S5U13719P00C100 Evaluation Board User Manual (Rev. 1.1) EPSON...
-
Page 12: Chapter 4 Technical Description
4.1 Power 4.1.1 Power Requirements The S5U13719P00C100 evaluation board requires an external regulated power supply (3.3V at 1A). The power is supplied to the evaluation board through pin 5 of the P2 header, or pin 29 of the H1 header. -
Page 13: Clocks
S1D13719 Mobile Graphics Engine. 4.3 Reset The S5U13719P00C100 evaluation board can be reset using a push-button, or via an active low reset signal from the host development platform, on pin 30 of connector H1. The reset signal will reset the S1D13719 Mobile Graphics Engine and is also available on the H3 and H7 connectors, so that camera modules connected to the board can be reset. -
Page 14: Connecting To The Epson S5U13U00P00C100 Usb Adapter Board
When the S5U13719P00C100 is connected to the S5U13U00P00C100 USB Adapter board, there are 2 LEDs on S5U13719P00C100 which provide a quick visual status of the USB adapter. LED1 blinks to indicate that the USB adapter board is active. LED2 turns on to indicate that the USB has been enumerated by the PC. - Page 15 For the pinout of connectors P1 and P2, see Section Chapter 6, “Schematic Diagrams” on page 23. Note A windows driver must be installed on the PC when the S5U13719P00C100 is used with the S5U13U00P00C100 USB Adapter Board. The S1D13xxxUSB driver is available at www.erd.epson.com.
-
Page 16: Lcd Panel Interface
CCFL backlight. Usually, the inverter current consumption is higher than the maximum 100mA current avail- able from the on-board voltage regulator. The following diagram shows the location of the LCD panel connectors H4 and H5. H4 and H5 are both 0.1x0.1”, 40-pin headers (20x2). EPSON S5U13719P00C100 Evaluation Board User Manual (Rev. 1.1) - Page 17 Chapter 4 Technical Description Figure 4-3: LCD Panel Connectors Locations (H4, H5) For the pinout of connectors H4 and H5, see Section Chapter 6, “Schematic Diagrams” on page 23. S5U13719P00C100 Evaluation Board User Manual (Rev. 1.1) EPSON...
-
Page 18: Camera Interface
The S1D13719 camera interface has a strobe output, CMSTROUT, that is available on H6 connector. Note that connector H6 is not populated on the S5U13719P00C100 evaluation board. The following diagram shows the location of the camera connectors H3, H6 and H7. H3 and H7 are 0.1x0.1”, 20- pin headers (10x2). -
Page 19: Sd Card Interface
The S1D13719 Mobile Graphics Engine has 22 GPIO pins. Some GPIOs have multiple functions. The GPIO pins are routed to the connectors on the S5U13719P00C100 evaluation board. If any pin is configured as a GPIO, it will be available on the connectors as listed below: •... -
Page 20: Chapter 5 Parts List
CUR SMD LED0603 LNJ308G8LRA Micro Commercial Co. MBR0540 SOD-123 MBR0540-TP FILTR 3TERM 10MHZ TO ACH32C-333-T 300MHZ SMD ACH32C-333-T FILTER 3-TERM 60MHZ ACF451832-222 300MA SMD ACF451832-222 Samtec H1,H2 HEADER_17X2 TSW-117-07-G-D Samtec H3,H7 HEADER_10X2 TSW-110-07-G-D EPSON S5U13719P00C100 Evaluation Board User Manual (Rev. 1.1) - Page 21 Sullins Electronics Corp. SH5,SH6,SH7,SH8, JUMPER SHORTING TIN Shunt STC02SYAN SW8_DIPSW8 DIPSW8 SWITCH TACT SILVER PLT ITT Industries SW TACT-SPST GULLWING SW_EVQQW KSC241GLFS TPGND1, PC TEST POINT MINIATURE Keystone TP_SMT TP3.3VDD1 SMT TP_1206 5015 S5U13719P00C100 Evaluation Board User Manual (Rev. 1.1) EPSON...
- Page 22 IC 2.7V 100MA LDO REG Texas Instruments TPS76927DBVT SOT-23-5 TPS76927DBVT IC CONV BOOST 40V FET National Semiconductor LM2733Y SW SOT23-5 LM2733YMF/NOPB OSC 32.768KHZ 523PPM Epson 32.768kHz OSC SG-3030JC 32.7680KB3:ROHS 14-Pin DIP 2-641609-1 EPSON S5U13719P00C100 Evaluation Board User Manual (Rev. 1.1)
-
Page 23: Chapter 6 Schematic Diagrams
Chapter 6 Schematic Diagrams Chapter 6 Schematic Diagrams SIOVDD CIO2VDD CIO1VDD PIOVDD PIOVDD PIOVDD PIOVDD HIOVDD HIOVDD HIOVDD PLLVDD COREVDD PLLVSS COREVDD COREVDD COREVDD COREVDD COREVDD Figure 6-1: S5U13719P00C100 Schematics (1 of 4) S5U13719P00C100 Evaluation Board User Manual (Rev. 1.1) EPSON... - Page 24 Chapter 6 Schematic Diagrams Figure 6-2: S5U13719P00C100 Schematics (2 of 4) EPSON S5U13719P00C100 Evaluation Board User Manual (Rev. 1.1)
- Page 25 Chapter 6 Schematic Diagrams Figure 6-3: S5U13719P00C100 Schematics (3 of 4) S5U13719P00C100 Evaluation Board User Manual (Rev. 1.1) EPSON...
- Page 26 Chapter 6 Schematic Diagrams Figure 6-4: S5U13719P00C100 Schematics (4 of 4) EPSON S5U13719P00C100 Evaluation Board User Manual (Rev. 1.1)
-
Page 27: Chapter 7 S5U13719P00C100 Board Layout
Chapter 7 S5U13719P00C100 Board Layout Chapter 7 S5U13719P00C100 Board Layout Figure 7-1: S5U13719P00C100 Board Layout - Top View S5U13719P00C100 Evaluation Board User Manual (Rev. 1.1) EPSON... - Page 28 Chapter 7 S5U13719P00C100 Board Layout Figure 7-2: S5U13719P00C100 Board Layout - Bottom View EPSON S5U13719P00C100 Evaluation Board User Manual (Rev. 1.1)
-
Page 29: Chapter 8 References
Chapter 8 References Chapter 8 References 8.1 Documents • Epson Research and Development, Inc., S1D13719 Hardware Functional Specification, document number X59A-A-001-xx. 8.2 Document Sources • Epson Research and Development Website: http://www.erd.epson.com. S5U13719P00C100 Evaluation Board User Manual (Rev. 1.1) EPSON... -
Page 30: Chapter 9 Change Record
• chapter 6 Schematic Diagrams - update all schematic diagrams wit new diagrams X59A-G-003-01 Revision 1.0 - Issued: January 14, 2008 • Initial release of this manual X59A-G-003-00 Revision 0.01 - Issued: October 19, 2007 • Initial draft of this manual EPSON S5U13719P00C100 Evaluation Board User Manual (Rev. 1.1) - Page 31 20/F, Harbour Centre, 25 Harbour Road Wanchai, Hong Kong Phone: +852-2585-4600 FAX: +852-2827-4346 Telex: 65542 EPSCO HX EPSON TAIWAN TECHNOLOGY & TRADING LTD. 14F, No. 7, Song Ren Road, Taipei 110, TAIWAN Phone: +886-2-8786-6688 FAX: +886-2-8786-6660 EPSON SINGAPORE PTE., LTD.