Related Manuals for Epson S5U1C60N08E
Summary of Contents for Epson S5U1C60N08E
- Page 1 MF1180 - 02a CMOS 4 - BIT SINGLE CHIP MICROCOMPUTER S5U1C60N08E Manual (Evaluation Board for S1C60N08)
- Page 2 No part of this material may be reproduced or duplicated in any form or by any means without the written permission of Seiko Epson. Seiko Epson reserves the right to make changes to this material without notice. Seiko Epson does not assume any...
- Page 3 Configuration of product number Devices 60N01 0A01 Packing specifications 00 : Besides tape & reel 0A : TCP BL 2 directions 0B : Tape & reel BACK 0C : TCP BR 2 directions 0D : TCP BT 2 directions 0E : TCP BD 2 directions 0F : Tape &...
-
Page 5: Table Of Contents
CONTENTS S5U1C60N08E Manual (Evaluation Board for S1C60N08) This manual describes how to operate the S5U1C60N08E, a debugging tool for the S1C60N08 4-bit, single- chip microcomputer. Refer to the "S1C60N08 Technical Manual" for details of the S1C60N08, and the "S5U1C62000A Manual"... -
Page 7: Introduction
∗ The name 'EVA6008' on the development tool is the old name of the product. 1.2 S5U1C60N08E Components When unpacking the S5U1C60N08E, check that the following goods are present: (1) S5U1C60N08E main unit ..................1 (2) LCD connection cable and connector (60-pin flat type) ........1 set (3) I/O connection cable and connector (50-pin flat type) ........ -
Page 8: Product Specifications
2 PRODUCT SPECIFICATIONS 2 PRODUCT SPECIFICATIONS The components specifications of the S5U1C60N08E are listed below. S5U1C60N08E 203 mm (width) × 275 mm (depth) × 65 mm (height) (Including rubber feet) Dimensions: Weight: About 2.04 kg (main unit only) Color: Cygnus white Power supply: 5 V (±10%) DC, 3 A or more... -
Page 9: Names And Functions Of Parts
Install the EPROM containing the application program and execute the program. Interface with ICE The S5U1C60N08E can interface with the ICE so that a higher level debugging environment may be established. Setting hardware options by installing function option and segment option ROMs Hardware options, i.e., I/O ports and segments, can be specified by writing option data for the... -
Page 10: Board (Under Top Cover)
CR oscillation is selected for the OSC3 oscillator type by mask option. The CR oscillation frequency can be checked with an oscilloscope or other instrument by connecting to pin 10 of the sub-board connector. Turning clockwise: High frequency Turning counterclockwise: Low frequency EPSON S5U1C60N08E MANUAL (EVALUATION BOARD FOR S1C60N08) - Page 11 "0". • LED9 (DONE) This LED lights when the S5U1C60N08E has completed configuration at power-on and is ready for debugging. If this LED does not light several seconds after power- on, turn the power off and then on again.
-
Page 12: S5U1C60N08E I/O, Lcd And Sub-Board Connectors
3 NAMES AND FUNCTIONS OF PARTS 3.3 S5U1C60N08E I/O, LCD and Sub-board Connectors Table 3.3.1 I/O #0 connector pins Table 3.3.2 I/O #1 connector pins Pin No. Signal name Pin No. Signal name Pin No. Signal name Pin No. Signal name... -
Page 13: Cable Connection
Note: Turn the power of all equipment off before connecting or disconnecting cables. 4.1 Connection to ICE The S5U1C60N08E is connected to the ICE by connecting the two interface cables (F1 and F5). Use S5U1C60N08E connectors F1 and F5 with the projections facing outwards. Use ICE connectors F1 and F5 with the projections facing inwards (cable side). -
Page 14: Power Cable Connection
4 CABLE CONNECTION 4.2 Power Cable Connection When using the S5U1C60N08E on its own, it must be supplied with power (5 V DC, 3 A or more) from an external source through the power cable. When the S5U1C60N08E is connected to the ICE, power is supplied by the ICE; therefore, the power cable is not necessary. -
Page 15: Operation Method Of S5U1C60N08E
Mount the LCD panel, keys, and switches on the board to build a target system. Use the I/O connector and LCD connector supplied with the S5U1C60N08E to connect the S5U1C60N08E to the target system. (For the pin layout of each connector, refer to Section 3.3, "S5U1C60N08E I/O, LCD and Sub-board Connectors".) Note: There is some difference in specifications between the S5U1C60N08E and the actual CPU. -
Page 16: Independent Use Of S5U1C60N08E
(2) Keep on turning the POWER switch off. 5.3.1 Power on/off Power to the S5U1C60N08E is supplied by the ICE, and the power is switched on and off by pressing the POWER switch of the ICE. Keep the POWER switch of the S5U1C60N08E off. -
Page 17: Precautions
6.1 Precautions for Operation • Turn the power of all equipment off before connecting or disconnecting cables. • To turn the POWER switch of the S5U1C60N08E off, then on again, wait for at least 10 seconds after turning off before turning on. - Page 18 OSC3. The same applies when turning the OSC1 oscillation off after switching the clock from OSC3 to OSC1. The S5U1C60N08E may operate if this processing is performed at the same time. Be sure to use separate instructions according to the actual IC when creating the program.
- Page 19 Central Phone: +852-2585-4600 Fax: +852-2827-4346 101 Virginia Street, Suite 290 Telex: 65542 EPSCO HX Crystal Lake, IL 60014, U.S.A. EPSON TAIWAN TECHNOLOGY & TRADING LTD. Phone: +1-815-455-7630 Fax: +1-815-455-7633 10F, No. 287, Nanking East Road, Sec. 3 Northeast Taipei 301 Edgewater Place, Suite 120...
- Page 20 S5U1C60N08E Manual (Evaluation Board for S1C60N08) ELECTRONIC DEVICES MARKETING DIVISION EPSON Electronic Devices Website http://www.epsondevice.com First issue April, 1999 Printed March, 2001 in Japan...