Related Manuals for Epson S5U1C62N51E1
Summary of Contents for Epson S5U1C62N51E1
- Page 1 CMOS 4-BIT SINGLE CHIP MICROCOMPUTER S5U1C62N51E1 Manual (Evaluation Board for S1C60N01/60N02/60N05/62N51/6S3N7) Rev.1.0...
- Page 2 Seiko Epson. Seiko Epson reserves the right to make changes to this material without notice. Seiko Epson does not assume any liability of any kind arising out of any inaccuracies contained in this material or due to its application or use in any product or circuit and, further, there is no representation that this material is applicable to products requiring high level reliability, such as, medical products.
- Page 3 The information of the product number change Starting April 1, 2001, the product number will be changed as listed below. To order from April 1, 2001 please use the new product number. For further information, please contact Epson sales representative.
-
Page 4: Table Of Contents
S5U1C62N51E1 Manual (Evaluation Board for S1C60N01/60N02/60N05/62N51/6S3N7) This manual describes how to operate the S5U1C62N51E1, a debugging tool for the S1C62N51, S1C6S3N7, S1C60N01, S1C60N02 and S1C60N05 4-bit single-chip microcomputer. Refer to the Technical Manual of each model for details of the S1C62N51, S1C6S3N7, S1C60N01, S1C60N02 and S1C60N0, and the "S5U1C62000A Manual"... -
Page 5: Introduction
∗ The name 'EVA6251R' on the development tool is the old name of the product. 1.2 S5U1C62N51E1 Components When unpacking the S5U1C62N51E1, check that the following goods are present: (1) S5U1C62N51E1 main unit ................1 (2) LCD connection cable and connector (60-pin flat type) ......1 set (3) I/O connection cable and connector (50-pin flat type) ....... -
Page 6: Product Specifications
2. PRODUCT SPECIFICATIONS 2. PRODUCT SPECIFICATIONS The components specifications of the S5U1C62N51E1 are listed below. S5U1C62N51E1 203 mm (width) × 275 mm (depth) × 65 mm (height) (Including rubber feet) Dimensions: Weight: About 2.04 kg (main unit only) Color: Cygnus white Power supply: 5 V (±10%) DC, 3 A or more... -
Page 7: Names And Functions Of Parts
Install the EPROM containing the application program and execute the program. Interface with ICE The S5U1C62N51E1 can interface with the ICE so that a higher level debugging environment may be estab- lished. Setting hardware options by installing function option and segment option ROMs Hardware options, i.e., I/O ports and segments, can be specified by writing option data for the function option... -
Page 8: Board (Under Top Cover)
Note: Do not use the option data generated by the function and segment option generators for an Evaluation Board other than the S5U1C62N51E1. Data created by the old function and segment option generators cannot be used. It will cause a malfunction. - Page 9 • POWER This LED lights when the S5U1C62N51E1 turns on. • HLT/SLP This LED lights when the CPU enters HALT or SLEEP status. (The S5U1C62N51E1 does not support SLEEP mode.) • AD0 This LED indicates the status of the address 0 (AD0) signal. It can be used to check whether or not the S5U1C62N51E1 works.
-
Page 10: S5U1C62N51E1 I/O And Lcd Connectors
This pin is used for monitoring the signal (analog waveform) input to the CS pins while the R/F converter is operating. (The R/F converter function is available when the S5U1C62N51E1 is set for S1C62N51, 60N02 or 60N05.) The frequency in each mode can be measured without affecting the R/F conversion accuracy. -
Page 11: Cable Connection
4. CABLE CONNECTION 4. CABLE CONNECTION This section describes how to connect the power cable to the S5U1C62N51E1, and the S5U1C62N51E1 to the ICE and the target system. Note: Turn the power of all equipment off before connecting or disconnecting cables. -
Page 12: Operation Method Of S5U1C62N51E1
Section 3.3, "S5U1C62N51E1 I/O and LCD Connectors".) Note: There is some difference in specifications between the S5U1C62N51E1 and the actual CPU. Refer to Section 6.2, "Differences from Actual IC" when building a target system. -
Page 13: Independent Use Of S5U1C62N51E1
This section describes operation when using the S5U1C62N51E1 by itself. The S5U1C62N51E1 may be used independently by connecting a power supply to it. Use a 5 V DC regulator (more than 3 A) as an external power supply. Connect it with the correct polarity (+ and -). -
Page 14: Precautions
6S37, 6001, 6002 and 6005 must never been used. • Turn the power of all equipment off before connecting or disconnecting cables. • To turn the POWER switch of the S5U1C62N51E1 off, then on again, wait for at least 10 seconds after turning off before turning on. - Page 15 6. PRECAUTIONS • The oscillation start and stop times are different from those of the IC. Because the logic level of S5U1C62N51E1 is higher than it of the actual IC. R/F converter set for the (when S1C62N51, 60N02 or 60N05 is selected by function option) •...
- Page 16 Phone: +49-89-14005-0 FAX: +49-89-14005-110 12/F, Dawning Mansion, Keji South 12th Road, Hi- Tech Park, Shenzhen Phone: +86-755-2699-3828 FAX: +86-755-2699-3838 EPSON TAIWAN TECHNOLOGY & TRADING LTD. 14F, No. 7, Song Ren Road, Taipei 110 Phone: +886-2-8786-6688 FAX: +886-2-8786-6660 EPSON SINGAPORE PTE., LTD.