Tools Needed - KitchenAid YKERC608LS0 Installation Instructions Manual

Before you start...
Your safety and the safety of
others are very important.
We have provided many important safety
messages in this manual and on your
appliance. Always read and obey all
safety messages.
This is the safety alert symbol.
This symbol alerts you to
potential hazards that can kill
or hurt you and others.
All safety messages will follow the safety
alert symbol and either the word
"DANGER" or "WARNING." These
words mean:
You can be ki!led or seriously injured
if you don't immediately follow
instructions.
You can be killed or seriously injured
if you don't follow instructions.
All safety messages will tell you what the
potential hazard is, tell you how to
reduce the chance of injury, and tell you
what can happen if the instructions are
not followed.
IMPORTANT: Observe all governing codes
and ordinances.
Earthed/grounded electrical outlet is
required.
Cabinet opening dimensions that are
shown must be used.
Do not pinch the power supply cord
between the range and the wall.
Do not seal range to side cabinets.
Read electrical and carpentry instructions.
Proper installation is your responsibility.
A qualified technician must install this
range. Make sure you have everything
necessary for correct installation, it is the
customer's responsibility to make sure
that the countertop has been properly
prepared and that the installation
clearances specified on the model/serial
rating plate are met.The model/serial
rating plate is located on the frame
behind the drawer.
To eliminate the risk of burns or fire by
reaching over heated surface units,
cabinet storage space located above the
surface units should be avoided. If
cabinet storage is to be provided, the risk
can be reduced by installing a range
hood that projects horizontally a
minimum of 5 inches beyond the bottom
of the cabinets.
All openings in the wall or floor where
range is to be installed must be sealed.
IMPORTANT: Some cabinet and building
materials are not designed to withstand
the heat produced by the oven for baking
and self-cleaning. Check with your
builder or cabinet supplier to make sure
that the materials used will not discolor,
delaminate or sustain other damage.
it is the customer's responsibility:
To contact a qualified electrical installer.
To assure that the electrical installation is
adequate and in conformance with
National Electrical Code, ANSI/NFPA 70
-- latest edition x-, or CSA Standard C22.1,
Canadian Electrical Code, Part 1 -- latest
edition x-s, and all local codes and
ordinances.
NOTE:The metal chassis of the range
must be earthed/grounded in order for
the control panel to work. If the metal
chassis of the range is not earthed/
grounded, no keypads will operate.
Check with a qualified electrician if you
are not sure the range is earthed/
grounded.
Mobile home installation
The installation of this range must
conform with the Manufactured Home
Construction and Safety Standard,Title
24 CFR, Part 3280 [formerly the Federal
Standard for Mobile Home Construction
and Safety, Title 24, HUD (Part 280)] or,
when such standard is not applicable, the
Standard for Manufactured Home
Installations, ANSI A225.1/NFPA 501A*,
or with local codes.
In Canada, the installation of this range
must conform with the current standards
CAN/CSA-Z240 -- latest edition **, or
with local codes.
When this range is installed in a mobile
home, it must be secured to the floor
during transit. Any method of securing
the range is adequate as long as it
conforms to the standards listed above.
Four-wire power supply cord or cable
must be used in a mobile home
installation.The appliance wiring will
need to be revised.
Copies of the standards listed may be obtained
from:
* National Fire Protection Association
One Batterymarch Park
Quincy, Massachusetts, 02269
** CSA International
8501 East Pleasant Valley Rd.
Cleveland, Ohio 44131-5575
Tools needed:
Assemble the required tools and parts
before starting installation. Read and
follow the instructions provided with any
tools listed here.
level
flat-blade screwdriver
Phillips screwdriver
3/8" drive ratchet
3/8" and 5/16" nut drivers
pliers
adjustable wrench
measuring tape or ruler
hand or electric drill
wood floors: 1/8" drill bit
concrete/ceramic floors:
3/16" carbide-tipped masonry drill bit
(Hammer may be needed for anchors.)
Parts suppfied:
anti-tip bracket
2 plastic
anchors
2 screws
(#10 x 1-1/2")
Brackets must be securely mounted to sub-floor.
Thickness of flooring may require longer screws to
anchor bracket to sub-floor. Longer screws are
available from your local hardware store.