Washing Sequence - Haier AWT-80LI User Manual

Washing sequence

Wash timer Wash selector
(To set to below 2 minute,
(Strong current,
first set to 5 minute then
standard current)
turn it back. it can increase
the service life of the timer).
STRONG STRONG
STANDARD STANDARD
3 3
15 15
12 12 6 6
WASH TIMER WASH TIMER
9 9
Âé
Wash
1 Inlet selector
(1) Set inlet selector to Wash
(2 )Adjust water level rod to a position as needed.
2. Fill the water and add the dissolved washing
powder to make the water level reach the preset
position. (Figure 2)
Run washing program for some time to stir and
dissolve the powder completely.
3.Put in the laundries. If the water quantity is
insufficient, please add water.
4.Select the current.
Select the strength of the current according to
the laundries. (Figure 3)
5.Select the washing time
Select the washing time according to the
laundries. (Figure 4)
6.After washing,the buzzer will ring .Set
the "WASH SELECTOR" at "DRAIN".
(Figure 5).
8 8
Spin timer
(to set to below 1 minute,
first set to 2 minute then
turn it back. it can increase
the service life of the timer).
5 5 1 1
DRAIN DRAIN
4 4 2 2
SPIN TIMER SPIN TIMER
WASH SELECTOR WASH SELECTOR
3 3
side. Figure 1
SPIN
WASH
Figure 1
Figure 2
STRONG STRONG
STANDARD STANDARD
DRAIN DRAIN
Figure 3
3 3
15 15
12 12 6 6
Figure 4
9 9
STRONG STRONG
STANDARD STANDARD
DRAIN DRAIN
Figure 5
How to change the direction of the drain hoses
Figure 1 indicates the ex factory installation
position of the drain hose.
Extend the drain hose from the side of spin tub.
Take off the drain hose from the hanging
hole of the cabinet. Pull the drain hose
fixing hook outwards gently to take out
the drain hose from the two fixing hooks.
(As per Figure 2)
Rotate the drain hose fixing hook for 90
to take it out from the installation hole
(As per Figure 3).
Install the two drain hose fixing hooks taken
out into the installation hole at the other side of
the base frame (to aim at the installation hole
accurately you can lean the washing machine
forward slightly).Then rotatefor 90 (As per Figure 4).
Pull the fixing hook outwards slightly. Inlay the drain
hose into the fixing hooks reliably along the groove
at spin tub side, and make it extend towards spin
tub side..
Then hang the drain hose into the hanging hole at
the spin tub side. (As per Figure 5).
Extend the drain hose from the back side
Take out the drain hose from the two fixing hooks.
make it extend towards back side.(Extend the drain
hose from the side of back, hang the drain hose in
to the hanging hole at the both sides) . (As per Figure 6).
Install the water inlet hose; Select the water level
Insert the water inlet hose into the water-filling
entrance on the control panel directly.(pull it
out to dismantle it)
Select water level according to the
quantity of the laundries.
Set the water level adjusting lever
to needed line.
Use the new water inlet hose provided
with the machine to connect to the
water faucet.Old hose sets should
not be reused.
Side sectional view
Drain hose Fixing hook
fixing hook installation hole
Pull outwards
slightly
Take off
the drain hose
Drain hose
Figure 1
Figure 2
fixing hook
Rotate the fixing
Rotate the fixing
hook for 90
hook for 90
to fix it
Take off the fixing
Insert the fixing hook into the
hook downwards
installation hole upwards
Figure 4
Figure 3
Figure 5
Figure 6
Water inlet hose
Water level
indicator
Maximum Max.
Med
Medium
Min
Minimum
5
Drain hose