Table of Contents
Advertisement
Quick Links
.46-Size Nitro Powered Air Boat
Owner's Manual
Specifications
Length .................................................................................................31 in (787mm)
Beam ...................................................................................................15 in (381mm)
Engine ...................................................................................... Evolution .46 (7.6cc)
Radio System ...........................................................Pro Boat AM 27MHz 2-Stick
Advertisement
Table of Contents
Related Manuals for Pro Boat Vortex 46 Airboat
Summary of Contents for Pro Boat Vortex 46 Airboat
- Page 1 .46-Size Nitro Powered Air Boat Owner's Manual Specifications Length ....................31 in (787mm) Beam ....................15 in (381mm) Engine ..................Evolution .46 (7.6cc) Radio System ............Pro Boat AM 27MHz 2-Stick...
-
Page 2: Introduction
It is preferable to operate the Pro Boat Vortex 46 only in calm water. We also suggest that you do not run the Vortex 46 in salt water. -
Page 3: Table Of Contents
Section 2: Rudder Installation ....................5 Section 3: Installation of Receiver and Transmitter Batteries ..........6 Section 4: Range Checking the Pro Boat Radio System ............7 Section 5: Evolution Power System ..................8 Section 6: Starting the Evolution Engine ................9 Section 7: Engine Adjustments .................... -
Page 4: Warranty Information
Warranty Information Pro Boat™ guarantees this kit to be free from defects in both material and workmanship at the date of purchase. This warranty does not cover any parts damaged by use or modification. In no case shall Horizon Hobby’s liability exceed the original cost of the purchased kit. Further, Horizon Hobby reserves the right to change or modify this warranty without notice. -
Page 5: Section 1: Building The Boat Stand
Section 1: Building the Boat Stand 1. There are 4 plywood pieces. The 2 short plywood pieces are the ends of the boat stand. 2. Attach the 2 long plywood pieces of the interlocking boat stand to one end of the short plywood pieces. -
Page 6: Section 3: Installation Of Receiver And Transmitter Batteries
Section 3: Installation of Receiver and Transmitter Batteries Receiver Batteries 3. Remove the dry cell battery holder from the radio box and unwrap the foam from around the 1. Remove the knurled aluminum nut that dry cell battery holder. Install 4 “AA” alkaline secures the cockpit. -
Page 7: Section 4: Range Checking The Pro Boat Radio System
Likewise, the boat of fresh batteries. should be turned off first before the transmitter. Section 4: Range Checking the Pro Boat Radio System Before the first run of the Vortex 46, you should 3. If everything appears to be operating... -
Page 8: Section 5: Evolution Power System
Section 5: Evolution Power System The Evolution Power System has been specifically • Only use a “Start Stick” or electric starter to start designed with the first-time modeler in mind. the engine. The engine and special three blade propeller have been designed to give your Vortex 46 optimum performance. -
Page 9: Section 6: Starting The Evolution Engine
Section 6: Starting the Evolution Engine Field Equipment Required The following are included in the Hangar 9® Start- Up Field Accessory Pack (HANSTART) • Sturdy cardboard construction tote box • Manual fuel pump • Hangar 9 glow plugs (2) • 4-way wrench •... -
Page 10: Section 7: Engine Adjustments
Section 7: Engine Adjustments Fine-Tuning the High-Speed Needle Model engines run on a mixture of fuel and air. The high-speed and low-speed needle valves control Start your engine and advance the throttle to full, the ratio of fuel to air that the engine receives. If then pinch the fuel line going to the engine. -
Page 11: Troubleshooting Guide
Glow plug failed due to lean engine setting: richen carburetor settings and replace glow plug Section 8: Maintenance The Pro Boat™ Vortex 46 should provide many When refueling, always wipe away any excess fuel hours of exciting high-speed racing fun with just that may have spilled into or on the boat. -
Page 12: Section 9: Vortex 46 Replacement Parts
Section 9: Vortex 46 Replacement Parts In the event that you need to purchase replacement parts for your engine or the Vortex 46 please see your local hobby store. You can also purchase them from Horizon Hobby by calling 1-800-338-4639 or shop online @ www.horizonhobby.com Part # Description... -
Page 13: Appendix
Appendix Engine and fuel line installation (viewed from top). Servo linkage setup. Rudder linkage setup. Checking the fuel level from rear of engine pod. -
Page 14: Parts Diagram
Parts Diagram PRB2705 PRB2706 PRB2713 PRB2711 EVOE100P PRB2704 PRB2703 EVOE100S PRB2701 PRB2710 PRB2709 PRB2708 PRB2707 PRB2712 PRB2716 PRB2702 PRB2714... -
Page 15: Notes
Notes... -
Page 16: Champaign, Illinois
© 2005, Horizon Hobby, Inc. 4105 Fieldstone Road Champaign, Illinois 61822 (877) 504-0233 www.horizonhobby.com 05482 98133 This article corresponds to the EU-regulations and can be sold in all EU-countries. 0682 Printed in China 7713...
Need help?
Do you have a question about the Vortex 46 Airboat and is the answer not in the manual?
Questions and answers