Advertisement
Available languages
Available languages
This range is designed to hang from the countertop.
It
does not rest on the floor.
Be sure the bottom of any wall cabinets are a minimum
of 30" (76.2 cm) above the rangetop area.
To eliminate the hazard or reaching over heated
surface units, cabinet storage space located above the
surface units should be avoided. If cabinet storage is to
be provided, the hazard can be reduced by installing a
range hood that projects horizontally a minimum of 5"
(12.7 cm) beyond the bottom front edge of the
cabinets.
Important
Note: Door removal is not a requirement for
installation of the range, but is an added convenience.
Refer to the Use and Care Guide for oven door removal
instructions.
1.
Install base cabinets 30" (76.2 cm) apart, and be
sure they are plumb and level before attaching to
cou ntertop.
2.
Cut countertop
exactly as shown in Figure I. Shave
raised edge level to clear 31 I/2"
(81 cm) wide rim
on rolled edge styled countertops.
3.
Install the wiring junction box in an adjoining
cabinet or under the floor (range has 48"/122 cm of
conduit). Cut 1-I/4"
(3.2 cm) hole to bring conduit
to the junction box.
4.
To provide an optimum installation, tile top surface
of the countertop
must be level and flat (lie on the
same plane) around the 3 sides that are adjacent to
range cooktop. Proper adjustments to make the top
flat should be made or gaps between the
countertop may occur.
5.
_
To reduce the risk of damaging your
appliance, do not handle or manipulate it by the
ceramic: glass. Manipulate with care.
6.
Move range in front of cabinet opening.
7.
Push the electric conduit through the hole and
attach it to the junction box. Leave enough slack in
the conduit to allow the range to be pulled forward
several inches for service if necessary.
8.
Oven door is heavy. It is advisable
to remove
door and eliminate
its weight
as range is tifted
into position.
See oven door removal
instructions
in the Use and Care Guide. Lift the
range into position
on the countertop
and
make sure the appliance
is centered
in the
cutout
opening
to be sure that the flanges
of
the upper side paneJ are sitting
on the
countertop
to avoid gJass breakage.
Ranges with
Ceramic Ghss Cooktop
9.
This range is equipped with an anti-tip bracket
attached to the back of tile range with two screws.
If countertop thickness is greater than I/2" (1.3 cm),
relocate anti-tip bracket to tile lower position 1/4"
(6.4 ram) below (see Figure 1, page 1).
10. Anti-slide brackets Installtion (Figure 6):
1. Place the range so that it is about 6" ou of the
cabinet.
2. Insert from below the shoulder screws in the side
panel (one on each side)
3. Slide the range into its final position.
4. Position the "L" bracket against the side of tile
cabinet so that it is retained by the shoulder
screws, hold bracket and mark the holes on the
inside of tile cabinet. Drill pilot holes into cabinet
where you just marked (Caution should be take to
avoid drilling throught the opposite side of the
cabinet). Attach the "L" bracket to the cabinet
with the screws provided (don't forget to insert
the shoulder screw into tile bracket).
5. Repeat steps 4 on the other side.
11. Install the decorative lower trim under tile door using
tile screws provided with tile range.
Figure 6
Ranges with a lift-up
cooktop:
9.
Anti-tip/anti-slide
screws installation:
1. Slide the range to its final postion.
2. Lift the cooktop and secure range burner box to
cabinet with screws supplied to prevent range
from tipping (Figure 7).
10. Install tile decorative lower trim under the door
using
tile screws provided with the range.
Advertisement
