Download Print this page

Electrical Requirements; Adjusting Oven Height - Frigidaire FGEW2765KFB Installation Instructions Manual

27" (68.6 cm), 30" (76.2 cm) electric wall oven
Hide thumbs

Advertisement

important
Notes
to the
Installer
1.
Read all instructions contained in these installation
instructions before installing the wall oven.
2.
Remove all packing material from the oven
compartments before connecting the electrical supply
to the wall oven.
3.
Observe all governing codes and ordinances.
4.
Be sure to leave these instructions with the consumer.
5.
Oven door may be removed to facilitate installation.
6.
THESE OVENS ARE NOT APPROVED FOR
STACKABLE OR SIDE-BY-SIDE INSTALLATION.
important
Note
to the
Consumer
Keep these instructions with your Owner's Guide for the
local electrical inspector's use and future reference.
IMPORTANT
SAFETY
INSTRUCTIONS
• Be sure your wall oven is installed
and grounded
properly
by a qualified
installer
or service
technician.
This wall oven must be electrically
grounded
in
accordance
with
local codes or, in their absence,
with the National
Electrical
Code ANSI/NFPA
No.70= latest edition
in United Sates, or with CSA
Standard
C22.1, Canadian
Electrical
Code, Part 1,
in Canada.
Stepping,
leaning
or sitting
on the
door of this wall oven can result in serious injuries
and can also cause damage
to the wall oven.
Never use your wall oven for warming
or heating
the room. Prolonged use of the wall oven without
adequate ventilation can be dangerous.
The electrical power to the oven must
be shut off while line connections
are being made.
Failure to do so could result in serious injury or death.
1. Carpentry
Refer to figure 1 or 2 for the dimensions applicable to
your appliance, and the space necessary to receive the
oven. The oven support surface may be solid plywood or
similar material, however the surface must be level from
side to side and from front to rear.
2. Adjusting
Oven Height
Oven height can be adjusted with 2" (Scm) wide wood
shims when needed to fit into an existing cabinet cutout
opening, when cutout height exceeds 281/8"(71.4cm) for
the single wall oven or 491/2"(125.7cm) for the double
wall oven (see Figure 1 or 2). Place shims of appropriate
height beneath the oven side rails.
3. Electrical
Requirements
This appliance must be supplied with the proper voltage
and frequency, and connected to an individual, properly
grounded branch circuit, protected by a circuit breaker
or fuse. To know the circuit breaker or fuse required
by your model, see the serial plate to find the wattage
consumption and refer to table A to get the circuit
breaker or fuse amperage.
App
lance
protection
App lance
Protection
Rating Watts
circuit
Rating Watts
Circuit
240V
Recommended
208V
Recommended
Less than 4800W
20A
Less than 4100W
20A
4800W- 7200W
30A
4100W- 6200W
30A
7200W- g600W
40A
6200W- 8300W
40A
9600W and +
B0A
8300W and+
B0A
Table A
Observe all governing
codes and local ordinances
1.A 3-wire or 4-wire single phase 120/240 or 120/208
Volt, 60 Hz AC only electrical supply is required on a
separate circuit fused on both sides of the line (red
and black wires). A time-delay fuse or circuit breaker is
recommended. DO NOT fuse neutral (white wire). Only
certain cooktop models may be installed over certain
built-in electric oven models. Approved cooktops and
built-in ovens are listed by the MFG ID number (see the
insert sheet included in the literature package).
NOTE: Wire sizes and connections must conform with
the fuse size and rating of the appliance in accordance
with the American National Electrical Code ANSI/NFPA
No. 70-latest edition, or with Canadian CSA Standard
C22.1, Canadian Electrical Code, Part 1, and local codes
and ordinances.
An extension
cord should
not be used
with this appliance.
Such use may result in a fire,
electrical
shock, or other
personal
injury. If you need
a longer power cord you can purchase a 10' (3 m) power
cord kit #903056-9010
by calling the Service Center.
2.
These appliances should be connected to the fused
disconnect (or circuit breaker) box through flexible
armored or nonmetallic sheathed cable. The flexible
armored cable extending from the appliance should
be connected directly to the junction box. The
junction box should be located as shown in Figure
1 or Figure 2 and with as much slack as possible
remaining in the cable between the box and the
appliance, so it can be moved if servicing is ever
necessary.
3.
A suitable strain relief must be provided to attach
the flexible armored cable to the junction box.
S

Hide quick links:

Advertisement

loading

  Also See for Frigidaire FGEW2765KFB

  Related Manuals for Frigidaire FGEW2765KFB