Subscribe to Our Youtube Channel
Related Manuals for Excalibur Water Systems 2.0” High Capacity Premium Flow Series
Summary of Contents for Excalibur Water Systems 2.0” High Capacity Premium Flow Series
- Page 1 Excalibur WatEr SyStEmS 2.0” HiGH caPacity SuPEr FlOW SEriES DuPlEx WatEr SOFtENEr installation and Operations manual 142 Commerce Park Drive, Units M-O, Barrie ON L4N 8W8 www.excaliburwater.com...
- Page 2 2.0” High Capacity Premium Flow Series Water Softener: Premium flow water softener AC adapter for European use. 1. Water softener 220 - 240 VAC 50Hz input 24.0 VAC 750 MA output. 2. Water softener cable should be one unshielded pair of 22 AWG, UV Resistant UL2464 compliant wire.
- Page 3 Water Softener Custom Meter Wiring: 1. Water softener terminate end with a Molex series 2695 housing, Pin 22-01-3037 and (3) Molex series 41572 (or 40445) Pins, Pin 08-65-0805 (or 97-00-44). 2. Water auxiliary meter must be able to operate on 5VDC. Water softener Pin 1 = + 5VDC Water softener Pin 2 (centre) = SIGNAL Water softener Pin 3 = GROUND...
- Page 4 Water Softener Optional System Board: Water softener system board required for relay output and separate source inlet. 1) Water softener relay outlets 1 and 2 are normally open SPST dry contacts. 2) Water softener maximum power through water softener relays to be a) 1A, 30VDC b) 1A, 30VAC 3) Water softener separate souce inlet dreives require connection to a P/N 3063 or P/N 3063...
- Page 5 Water Softener Motorized Drive Operation: Viewing the water softener piston rod through the clear water softener clear dome is a visual indicator of the water softener drives current position. On the water softener motorized bypass drive, viewing the rod indicates that the water softener is in service. Viewing the water softener rod as shown on the water softener MAV indicates that the water softener common port is currently connected to the water softener “B”...
- Page 6 Water Softener Reversing Motorized Drive Direction: Water softener motorized bypass and water softener MAV drives are factory wired with the white wire on the right when viewing the water softener wiring harness as shown, reversing the water softener wires reverses the logic of the drive. The water softener wires can be removed from the housing by holding down the water softener locking tab in the small window while applying light pressure to the wire, being careful not to disengage the wire from its crimped on connector.
- Page 7 Water Softener Wiring Diagram Examples 2 Water Softener System: Water softener dual system with optional system optional system board for water softener relays outputs and separate source inlet.
- Page 8 Water softener 3 and 4 unit systems with no optional system boards (4 water softener shown)
- Page 10 Water softener 3 and 4 unit systems with optional systems boards for water softener relay outputs and separate inlet (4 water softeners shown)
- Page 11 Water Softener Programming Screen Quick Reference: 1. Water softener individual screen descriptions are detailed on the following pages. 2. Some water softener screens have been omitted for clarity. 1 10...
- Page 12 1 11...
- Page 13 1 12...
- Page 14 Water Softener Setting Time of Day: Water softener set time accessed by pressing set lock while in the water softener user screen. Use the up and down water softener arrows to scroll hours. This water softener AM/PM alternates at midnight. Water softener count error and the water softener number will flash when it is not detected.
- Page 15 Water Softener Typical User Screens: Water softener regen today wil display Water softener user 1 displays capacity when a regeneration is scheduled or remaining. Does not display if volumetric flash for a manually set regeneration. capacity is set to OFF. Water softener capacity remaining can be adjusted in 10 gallon increments by holding the water softener down arrow for >...
- Page 16 Water Softener Typical User Screens Continued: Water softener displays total water softener volume since install/reset individually re-settable using history reset sequence. Water softener displays the water softeners current system flow rate. The water softener does not display on single tank water softeners.
- Page 17 Water Softener System Set Up Screens: Water softener accessed by pressing next and down simultaneously for > 3 seconds. Water softener select country US or SI. This sets the water softener use of 12 or 24 hour clock and the water softener display of gallons or litres.
- Page 18 Single water softeners have a selection of hard water bypass, no hard water bypass or water softener relay operation. When the water softeners start to regenerate, the water softener hard water bypass will allow hard water bypass, no hard water bypass or water softener relay and two water softeners alternators have an additional selection of ALT-A setting the water softener no hard...
- Page 19 Water Softener Installer Setup Service Returns to Normal Operation After 5 Minutes: The water softener is accessed by pressing the water softener next and down simultaneously for > 3 seconds. Installer 1: Set water softener volumetric capacity or OFF. OFF will not be an option if the water softener day control is set to OFF.
- Page 20 Installer 4: Select water softener time of regen. Use water softener up and down arrows to scroll minutes. Installer 5: Select water softener time of 2nd water softener regen (if configured as a multiple regenerating water softener). Installer 2: Water softener 7 day time clock option to set water softener current day of the week.
- Page 21 Water Softener Setup Screens Continued: System Setup 6: Select water softener regeneration type Water softener delayed (DEL-1) Water softener delayed (DEL-2) Water softener delayed (DEL-3) Water softener delayed (DEL-4) Water softener delayed with multiple regenerations allowed per day would be used either to reduce the water softener reverse volume, or to accommodate a small water softener system relative to the treatment...
- Page 22 System Setup 9: Select water softener meter type or pulses. Water softener 2.0 meter (type) Water softener 1.5 meter (type) Water softener system pulses. System Setup 9B: Select water softener meter type pulses. Water softener screen does not show if pulses or water softener system pulses is not selected in the previous water softener screen.
- Page 23 Water Softener Time Screens Water Softener Returns to Normal Operation After 5 Minutes: Water softener is accessed by pressing the water softener next and down simultaneously for > 3 seconds, then by pressing next and down simultaneously again for > 3 seconds. Timer 1 - A: Select water softener time of cycle 1.
- Page 24 Timer 1 - B2 Select water softener timer of alternate regen cycle 2. 1 23...
- Page 25 Water Softener Timer Screens Continued: Timer 2: Set water softener output 1, these water softener settings will only be allowed with water softener system board installed. Time: Water softener relay is turned on after the water softener specified time from the start of the water softener regeneration and is left on for a specified time.
- Page 26 Water Softener Timer Screens Continued: Timer 3: Set water softener output 2, these water softener settings will only be allowed with water softener system board installed. Time: The water softener relay is turned on after the water softener starts on a specified time from the start of water softener regeneration and is left on for a specified time.
- Page 27 Water Softener Timer Screens Continued: Timer 4: Select water softener output 1. On water softener trigger set point per water softener previously selected. This water softener screen will not display if the water softener does not have a water softener system board, or if the water softener STBY was selected as the trigger.
- Page 28 Water Softener Timer Screens Continued: Timer 6: Select water softener output 2, on water softener trigger set point, per water softener previously selected. This water softener screen will not display if the water softener does not have a water softener system board, or if STBY was selected as the water softener trigger.
- Page 29 Water Softener Timer Screens Continued: Timer 7: Select water softener output 2 on duration before turning off. This water softener screen will not display if the water softener does not have a water softener system board. 1 28...
- Page 30 Water Softener Cycle Setup Screens: Water softener returns to normal operation after 5 minutes. Water softener is accessed by pressing water softener next and down buttons simultaneously for > 3 seconds, then by pressing water softener next and down buttons simultaneously again for >...
- Page 31 Water Softener Cycle Setup Screens Continued: Water softener cycle setup 2. Water softener select regeneration repeats, 1 - 10 or OFF. Water softener repeats regeneration cycle sequence 1 as selected number of times before water softener regenerates a single time with sequence 2. The following watre softener screens only show if the water softener is programmed for multiiple water softener regenerations in the previous water softener...
- Page 32 Water Softener Diagnostic Screens: Return water softener to normal operation after 5 minutes. Water softener is accessed by pressing water softener next and down buttons simultaneously for > 3 seconds. All water softener diagnostic history screens are resettable with the water softener history reset sequence while in the water softener diagnostics 1 screen.
- Page 33 Water Softener Diagnostic Screens Continued: Water softener diagnostics 4 Water softener history of volume used Use water softener arrows to select A day 0 = today 1 = yesterday 63 = 63 days ago (MAX) Water softener regen will display if a water softener regeneration occurs that day.
- Page 34 Water Softener Diagnostic Screens Continued: Water softener diagnostics 5 The water softener maximum flow rate for the last 28 days. The water softener maximum flow rate of the day. Water softener automatically toggles Simultaneously press the water softener up and down buttons.
- Page 35 Water Softener Diagnostic Screens Continued: Water softener diagnostics 6 Water softener total volume through the water softener. Water softener diagnostics 7 Water softener system totalizer for the last 63 days. Water softener only displays in a mater system. Water softener use for that day Water softener automatically toggles Simultaneously press water softener up and down.
- Page 36 Water Softener Diagnostic Screens Continued: Water softener total system flow for the selected hour Water softener automatically toggles 1 35...
- Page 37 Water Softener Valve History: Water softener returns to normal operation after 5 minutes non resettable Water softener accessed by pressing water softener up and down buttons simultaneously for > 3 seconds, then by pressing water softener up and down buttons simultaneously again for >...
- Page 38 Water Softener Error Codes: 1 37...
Need help?
Do you have a question about the 2.0” High Capacity Premium Flow Series and is the answer not in the manual?
Questions and answers